BS 3087-13-1991 Pliers and nippers - Specification for dimensions and test values of carpenters pincers《夹扭钳和剪断钳 第13部分 木工用夹钳尺寸和试验值规范》.pdf

《BS 3087-13-1991 Pliers and nippers - Specification for dimensions and test values of carpenters pincers《夹扭钳和剪断钳 第13部分 木工用夹钳尺寸和试验值规范》.pdf》由会员分享，可在线阅读，更多相关《BS 3087-13-1991 Pliers and nippers - Specification for dimensions and test values of carpenters pincers《夹扭钳和剪断钳 第13部分 木工用夹钳尺寸和试验值规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS3087-13: 1991 ISO9243:1988 Pliers and nippers Part13: Specification for dimensions and test values of carpenters pincersBS3087-13:1991 This British Standard, having been prepared under the directionof the Machine, Engineers and Hand Tools Standards Policy Committee, waspublished u

2、nder the authorityof the Standards Boardand comes into effect on 28February1991 BSI10-1999 The following BSI references relate to the work on this standard: Committee reference MTE/15 Draft for comment87/72296 DC ISBN 0 580 19276 8 Committees responsible for this British Standard The preparation of

3、this British Standard was entrusted by the Machine, Engineers and Hand Tools Standards Policy Committee (MTE/-) to Technical Committee MTE/15, upon which the following bodies were represented: British Coal Corporation British Telecommunications plc Consumer Policy Committee of BSI Electricity Supply

4、 Industry in United Kingdom Federation of British Engineers Tool Manufacturers Federation of British Hand Tool Manufacturers Handle Manufacturers Association Institute of Carpenters Institute of Trading Standards Administration Institution of Production Engineers Ministry of Defence Amendments issue

5、d since publication Amd. No. Date CommentsBS3087-13:1991 BSI 10-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope 1 2 Normative references 1 3 Dimensions, hardness and test values 2 Figure 1 Carpenters pincers 2 Table 1 3 Publication(s) referred to Inside ba

6、ck coverBS3087-13:1991 ii BSI 10-1999 National foreword This Part of BS3087 has been prepared under the direction of the Machine, Engineers and Hand Tools Standards Policy Committee. It is identical with ISO9243:1988 “Pliers and nippers Carpenters pincers Dimensions and test values”, published by th

7、e International Organization for Standardization (ISO). As work continues in ISO the number of tools covered by this standard will increase. BS3087-10 covers those tools in BS3087:1959 (withdrawn) that were not standardized by ISO because their style and application were exclusive to the UK. The Tec

8、hnical Committee has reviewed the provisions of ISO5744, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard to ISO5744:1988 is BS3087-4:1988. It is recommended that pliers, pincers and nippers should

9、be legibly and indelibly marked with a name, trademark or the manufacturing code that will allow traceability. BS3087-13 1)should be marked either on the tool or on its associated packaging. A British Standard does not purport to include all the necessary provisions of a contract. Users of British S

10、tandards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to4, an inside back cover and a back cover. This s

11、tandard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Cross-references International Standard Corresponding British Standard BS3087 Pliers and nippers ISO5743:1982 Part3:1986 Specification for

12、general requirements (Identical) 1) Marking BS3087-13:1991 on or in relation to a product represents a manufacturers declaration of conformity, i.e.a claim by or on behalf of the manufacturer that the product meets the requirements of the standard. The accuracy of the claim is therefore solely the r

13、esponsibility of the person making the claim. Such a declaration is not to be confused with third party certification of conformity, which may also be desirable.BS3087-13:1991 BSI 10-1999 1 1 Scope This International Standard specifies the principle dimensions of carpenters pincers and the test valu

14、es in order to verify their aptitude to function in conformity with ISO5744. It also specifies the minimum hardness of the cutting edge. The general technical requirements are given in ISO5743. The carpenters pincers illustrated in this International Standard are examples only and are not intended t

15、o affect the manufacturers design. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and

16、parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards listed below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO5743:1982, Pliers and nippers General

17、technical requirements. ISO5744:1988, Pliers and nippers Methods of test. BS3087-13:1991 2 BSI 10-1999 3 Dimensions, hardness and test values Figure 1 Carpenters pincersBS3087-13:1991 BSI 10-1999 3 Table 1 Carpenters pincers shall have a minimum cutting edge hardness of45HRC. After the load test, th

18、e permanent set s shall not exceed the value given in Table 1. If the distance L 1is not suitable for the load test, the following formula may be applied: where F is the load which is not given in Table 1; F is the load given in Table 1; L 1is the distance from the centre of the joint rivet to the p

19、oint of application of the load given in Table 1;is the measured distance from the centre of the joint rivet to the point of application of the load. Pincers Load test type1 type2 Load Maximum permanent set s max a L L 3 w 3 T 1 w 1 G L 1 F min. min. min. max. 5 min. mm mm mm mm mm mm mm mm N mm 160

20、 8 180 9 200 10 224 10 250 10 280 15 11,2 12,5 14 16 18 20 32 36 40 45 50 56 16 18 20 22 25 28 14 16 18 20 22 25 45 45 45 48 50 53 12,5 14 16 18 20 22 106 118 132 150 170 190 710 710 800 900 1000 1120 1,2 1,4 1,6 1,8 2 2,2 a s = w 1 w 2(See ISO5744.) F FL 1 L 1 - = L 14 blankBS3087-13:1991 BSI 10-19

21、99 Publication(s) referred to See national foreword.BS3087-13: 1991 ISO9243:1988 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the internat

22、ional level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We wou

23、ld be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating se

24、rvice called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for interna

25、tional standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Techn

26、ical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive

27、 substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internatio

28、nal standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This doe

29、s not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.