ASTM G148-1997(2011) Standard Practice for Evaluation of Hydrogen Uptake Permeation and Transport in Metals by an Electrochemical Technique《用电化学技术评价金属中氢吸取 渗透和运输的标准操作规程》.pdf

《ASTM G148-1997(2011) Standard Practice for Evaluation of Hydrogen Uptake Permeation and Transport in Metals by an Electrochemical Technique《用电化学技术评价金属中氢吸取 渗透和运输的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM G148-1997(2011) Standard Practice for Evaluation of Hydrogen Uptake Permeation and Transport in Metals by an Electrochemical Technique《用电化学技术评价金属中氢吸取 渗透和运输的标准操作规程》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: G148 97 (Reapproved 2011)Standard Practice forEvaluation of Hydrogen Uptake, Permeation, and Transportin Metals by an Electrochemical Technique1This standard is issued under the fixed designation G148; the number immediately following the designation indicates the year oforiginal adopti

2、on or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice gives a procedure for the evaluation ofhydrogen uptake, perm

3、eation, and transport in metals using anelectrochemical technique which was developed by Devana-than and Stachurski.2While this practice is primarily intendedfor laboratory use, such measurements have been conducted infield or plant applications. Therefore, with proper adaptations,this practice can

4、also be applied to such situations.1.2 This practice describes calculation of an effective diffu-sivity of hydrogen atoms in a metal and for distinguishingreversible and irreversible trapping.1.3 This practice specifies the method for evaluating hydro-gen uptake in metals based on the steady-state h

5、ydrogen flux.1.4 This practice gives guidance on preparation of speci-mens, control and monitoring of the environmental variables,test procedures, and possible analyses of results.1.5 This practice can be applied in principle to all metalsand alloys which have a high solubility for hydrogen, and for

6、which the hydrogen permeation is measurable. This methodcan be used to rank the relative aggressivity of differentenvironments in terms of the hydrogen uptake of the exposedmetal.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is therespon

7、sibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3G96 Guide for Online Monitoring of Corrosion in PlantEquipment (Electrical and Electrochemica

8、l Methods)3. Terminology3.1 Definitions:3.1.1 charging, nmethod of introducing atomic hydrogeninto the metal by galvanostatic charging (constant chargingcurrent), potentiostatic charging (constant electrode potential),free corrosion, or gaseous exposure.3.1.2 charging cell, ncompartment in which hyd

9、rogenatoms are generated on the specimen surface. This includesboth aqueous and gaseous charging.3.1.3 decay current, ndecay of the hydrogen atom oxida-tion current due to a decrease in charging current.3.1.4 Ficks second law, nsecond order differential equa-tion describing the concentration of diff

10、using specie as afunction of position and time. The equation is of the formCx,t!/t 5/xD1/xCx,t!# for lattice diffusion in onedimension where diffusivity is independent of concentration.See 3.2 for symbols.3.1.5 hydrogen flux, nthe amount of hydrogen passingthrough the metal specimen per unit area as

11、 a function of time.The units are typically concentration per unit area per unittime.3.1.6 hydrogen uptake, nthe concentration of hydrogenabsorbed into the metal (for example, g/cm3or mol/cm3).3.1.7 irreversible trap, nmicrostructural site at which ahydrogen atom has a infinite or extremely long res

12、idence timecompared to the time-scale for permeation testing at therelevant temperature, as a result of a binding energy which islarge relative to the migration energy for diffusion.3.1.8 mobile hydrogen atoms, nhydrogen atoms that areassociated with sites within the lattice.3.1.9 oxidation cell, nc

13、ompartment in which hydrogenatoms exiting from the metal specimen are oxidized.3.1.10 permeation current, ncurrent measured in oxida-tion cell associated with oxidation of hydrogen atoms.3.1.11 permeation transient, nthe increase of the perme-ation current with time from commencement of charging to

14、theattainment of steady state, or modification of charging condi-tions (that is, rise transient). The decrease of the permeation1This practice is under the jurisdiction of ASTM Committee G01 on Corrosionof Metals and is the direct responsibility of Subcommittee G01.11 on Electrochemi-cal Measurement

15、s in Corrosion Testing.Current edition approved May 1, 2011. Published May 2011. Last previousedition approved in 2003 as G149-97(2003). DOI:10.1520/G0148-97R11.2Devanathan, M.A.V., and Stachurski, Z., Proceedings of Royal Society, A270,90102, 1962.3For referenced ASTM standards, visit the ASTM webs

16、ite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United Stat

17、es.current with time resulting from a decrease in charging current(that is, decay transient).3.1.12 recombination poison, nchemical specie presentwithin the test environment in the charging cell which en-hances hydrogen absorption by retarding the recombination ofhydrogen atoms adsorbed onto the met

18、al surface into hydrogengas.3.1.13 reversible trap, nmicrostructural site at which ahydrogen atom has a residence time which is greater than thatfor the lattice site but is small in relation to the time to attainsteady-state permeation, as a result of low binding energy.3.2 Symbols:3.2.1 For the pur

19、poses of this practice the following sym-bols apply:A = exposed area of specimen in the oxidation cell(cm2)C(x,t) = lattice concentration of hydrogen as a function ofposition and time (mol/cm3)C0= sub-surface concentration of atomic hydrogen atthe charging side of the specimen (mol/cm3)Deff= effecti

20、ve diffusivity of atomic hydrogen, takinginto account the presence of reversible and irre-versible trapping (cm2/s)Dl= lattice diffusion coefficient of atomic hydrogen(cm2/s)F = faradays constant (9.6485 3 104coulombs/mol)I(t) = time dependent atomic hydrogen permeation cur-rent (A)Iss= steady-state

21、 atomic hydrogen permeation current(A)J(t) = time-dependent atomic hydrogen permeation fluxas measured on the oxidation side of the specimen(mol/s/cm2)Jss= atomic hydrogen permeation flux at steady-state(mol/s/cm2)J(t)/Jss= normalized flux of atomic hydrogenL = specimen thickness (cm)t = time elapse

22、d from commencement of hydrogencharging (s)tb= elapsed time measured extrapolating the linearportion of the rising permeation current transientto J(t) =O(s)tlag= time to achieve a value of J(t)/Jss= 0.63 (s)x = distance into specimen from the charging surfacemeasured in the thickness direction (cm2)

23、.t = normalized time (D1t/L2)tlag= Normalized time to achieve a value of j(t)/Jss=0.63 (s)4. Summary of Practice4.1 The technique involves locating the metal membrane(that is, specimen) of interest between the hydrogen chargingand oxidation cells. In the laboratory, the charging cell containsthe env

24、ironment of interest. Hydrogen atoms are generated onthe membrane surface exposed to this environment. In field orplant measurements, the wall of the pipe or vessel can be usedas the membrane through which measurement of hydrogen fluxare made. The actual process environment is on the chargingside of

25、 the membrane which eliminates the need for a chargingcell. See 7.1 for guidance on various specimen configurations.4.2 In gaseous environments, the hydrogen atoms are gen-erated by adsorption and dissociation of the gaseous species. Inaqueous environments, hydrogen atoms are produced by elec-troche

26、mical reactions. In both cases, some of the hydrogenatoms diffuse through the membrane and are then oxidized onexiting from the other side of the metal in the oxidation cell.4.3 The conditions (for example, environment and theelectrode potential) on the oxidation side of the membrane arecontrolled s

27、o that the metal surface is either passive or immuneto corrosion. The background current established under theseconditions prior to hydrogen transport should be relativelyconstant and small compared to that of the hydrogen atomoxidation current.4.4 The electrode potential of the specimen in the oxid

28、ationcell is controlled at a value sufficiently positive to ensure thatthe kinetics of oxidation of hydrogen atoms are limited by theflux of hydrogen atoms, that is, the oxidation current density isdiffusion limited.4.5 The total oxidation current is monitored as a function oftime. The total oxidati

29、on current comprises the backgroundcurrent and the current resulting from oxidation of hydrogenatoms. The latter is the permeation current.4.6 The thickness of the specimen is selected usually toensure that the measured flux reflects volume (bulk) controlledhydrogen atom transport. Thin specimens ma

30、y be used forevaluation of the effect of surface processes on hydrogen entryor exit (absorption kinetics or transport in oxide films).4.7 In reasonably pure, defect-free metals (for example,single crystals) with a sufficiently low density of microstruc-tural trap sites, atomic hydrogen transport thr

31、ough the materialis controlled by lattice diffusion.4.8 Alloying and microstructural features such as disloca-tions, grain boundaries, inclusions, and precipitate particlesmay act as trap sites for hydrogen thus delaying hydrogentransport. These traps may be reversible or irreversible depend-ing on

32、the binding energy associated with the particular trapsites compared to the energy associated with migration forhydrogen in the metal lattice.4.9 The rate of hydrogen atom transport through the metalduring the first permeation may be affected by both irreversibleand reversible trapping as well as by

33、 the reduction of anyoxides present on the charging surface.At steady state all of theirreversible traps are occupied. If the mobile hydrogen atomsare then removed and a subsequent permeation test conductedon the specimen the difference between the first and secondpermeation transients can be used t

34、o evaluate the influence ofirreversible trapping on transport, assuming a negligible role ofoxide reduction.4.10 For some environments, the conditions on the chargingside of the specimen may be suitably altered to induce a decayof the oxidation current after attainment of steady state. Therate of de

35、cay will be determined by diffusion and reversibletrapping only and, hence, can also be used to evaluate the effectof irreversible trapping on transport during the first transient.G148 97 (2011)24.11 Comparison of repeated permeation transients withthose obtained for the pure metal can be used in pr

36、inciple toevaluate the effect of reversible trapping on atomic hydrogentransport.4.12 This practice is suitable for systems in which hydrogenatoms are generated uniformly over the charging surface of themembrane. It is not usually applicable for evaluation ofcorroding systems in which pitting attack

37、 occurs unless thecharging cell environment is designed to simulate the localizedpit environment and the entire metal charging surface is active.4.13 This practice can be used for stressed and unstressedspecimens but testing of stressed specimens requires consider-ation of loading procedures.5. Sign

38、ificance and Use5.1 The procedures described, herein, can be used to evalu-ate the severity of hydrogen charging of a material produced byexposure to corrosive environments or by cathodic polariza-tion. It can also be used to determine fundamental properties ofmaterials in terms of hydrogen diffusio

39、n (for example, diffu-sivity of hydrogen) and the effects of metallurgical, processing,and environmental variables on diffusion of hydrogen inmetals.5.2 The data obtained from hydrogen permeation tests canbe combined with other tests related to hydrogen embrittlementor hydrogen induced cracking to a

40、scertain critical levels ofhydrogen flux or hydrogen content in the material for crackingto occur.6. Apparatus6.1 The experimental set-up shall consist of a separatecharging and oxidation cell of a form similar to Fig. 1. Sealedoxidation cells, in which an additional material (usually palla-dium), e

41、ither plated or sputter deposited onto or clampedagainst the specimen and the flux exiting this additionalmaterial is measured may be used provided that it is demon-strated that the introduction of this additional interface has noeffect on the calculated diffusivity. The clamping of thisadditional m

42、aterial may provide inaccurate permeation currentsin some systems due to the barrier effect at the interface (thatis, oxides, air gaps and so forth will act as a diffusion barrier).6.2 Non-metallic materials which are inert to the test envi-ronment should be used for cell construction.6.2.1 At tempe

43、ratures above 50C, leaching from the cellmaterial (for example, silica dissolution from glass in someenvironments) can modify the solution chemistry and mayinfluence hydrogen permeation.6.2.2 Polytetrafluoroethylene (PTFE) is an example of amaterial suitable for elevated temperatures up to about 90C

44、.6.2.3 Where metallic chambers are necessary (for contain-ment of high pressure environments), the materials chosenshall have a very low passive current to ensure minimal effecton the solution composition and shall be electrically isolatedfrom the membrane.6.3 The O-ring seal material should be sele

45、cted to minimizepossible degradation products from the seals and contamina-tion of the solution. This problem is particularly of concernwith highly aggressive environments and at high test tempera-tures.6.4 Double junction reference electrodes may be used wherenecessary to avoid contamination of tes

46、t solutions. At elevatedtemperatures, the use of a solution conductivity bridge arrange-ment with suitable inert materials is recommended.6.5 The location of the reference electrode in each compart-ment shall ensure minimal potential drop between the speci-men and the reference electrode. A Luggin c

47、apillary may beuseful in cases where the solution resistivity is high, small cellvolumes are used and long tests are conducted. See Guide G96for further guidance.6.6 Recording of oxidation (and, as appropriate, charging)current shall be made using a standard resistor and a highinternal impedance dig

48、ital voltmeter or by direct measurementusing a current monitoring device.6.7 The measurement devices should be traceable to na-tional standards and calibrated prior to testing.6.8 In some cases, stirring of the solution in the chargingcell may be required. This should be performed using suitablestir

49、ring motor and apparatus.7. Specimen7.1 DesignSpecimens may be in the form of plate or pipe.The dimensions shall enable analysis of the permeation tran-sient based on one-dimensional diffusion. For example, forplates with a circular exposed area, the radius exposed to thesolution should be sufficiently large relative to thickness. Aratio of radius to thickness of 10:1, or greater, is recommended.This condition may be made less stringent if the exposed areain the oxidation side is smaller than that on the charging side.A ratio of radius to thickness of 5:1