ASTM F993-1986(2006) Standard Specification for Valve Locking Devices《阀门锁紧装置标准规范》.pdf

《ASTM F993-1986(2006) Standard Specification for Valve Locking Devices《阀门锁紧装置标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F993-1986(2006) Standard Specification for Valve Locking Devices《阀门锁紧装置标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 993 86 (Reapproved 2006)An American National StandardStandard Specification forValve Locking Devices1This standard is issued under the fixed designation F 993; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification2covers the ap

3、plication, design, andmaterials for valve locking devices.1.2 Locking devices Types I and II described in thisspecification are designed to secure the valve in a fully openedor completely closed position.1.3 This specification does not apply to valves equippedwith locking devices from the valve manu

4、facturer, unless thisstandard is invoked in the procurement ordering data for thevalve or its locking device, or both.1.4 This specification is intended to supercede NASEAdrawing S4824-1385509. However, cancellation of that draw-ing and adoption of this specification can only be effected bythe navy.

5、2. Referenced Documents2.1 ASTM Standards:3A 36/A 36M Specification for Carbon Structural SteelA 167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and StripA 492 Specification for Stainless Steel Rope WireA 668/A 668M Specification for Steel Forgings, Carbonand Al

6、loy, for General Industrial UseB 209 Specification for Aluminum and Aluminum-AlloySheet and PlateB 580 Specification for Anodic Oxide Coatings on Alumi-numF 708 Practice for Design and Installation of Rigid PipeHangers2.2 Other Documents:ANSI B18.1 Small Solid Rivets4American Welding Society D1.1 on

7、 Steel53. Classification3.1 Valve locking devices shall be classified by the follow-ing types and grades in accordance with the method of lockingand material used.3.2 Types:3.2.1 Type IWire rope assembly (see Fig. 1 Fig. 2).3.2.2 Type IIHandwheel latch (see Fig. 3 Fig. 4).3.2.3 Type IIILocking shiel

8、d (see Fig. 5).3.3 Grades:3.3.1 Grade AStainless steel, Specification A 167, Type316.3.3.2 Grade BAnodized aluminum, Specification B 209,Alloy 5052.3.3.3 Grade CCarbon steel, commercial quality steel (seeSpecification A 36/A 36M).4. Ordering Information4.1 Orders for material under this specificatio

9、n shall includethe following:4.2 ASTM Designation and year of issue.4.3 Type.4.4 Grade.4.5 Padlock Size (if necessary).4.6 Rubber Coating (if necessary).4.7 Necessary Dimensions:4.7.1 Type I:4.7.1.1 Length of wire strand.4.7.1.2 Diameter of pipe.4.7.2 Type II:4.7.2.1 Maximum height (fully opened).4.

10、7.2.2 Minimum height (fully closed).4.7.2.3 Handwheel thickness.4.7.2.4 Handwheel depth.4.7.2.5 Diameter at location of attachment.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and

11、 Piping Systems.Current edition approved Feb. 1, 2006. Published February 2006. Originallyapproved in 1986. Last previous edition approved in 2001 as F 993 86 (2001).2This specification is intended to supersede NAVSEADrawing S4824-1385509.However, cancellation of that drawing and adoption of this sp

12、ecification can only beeffected by the Navy.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from A

13、merican National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.5Available from American Welding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.7.3 Type III:4.7.

14、3.1 Depth.4.7.3.2 Height.4.7.3.3 Width.4.7.3.4 Outside diameter (OD) of pipe.FIG. 1 Type IWire Rope AssemblyFIG. 2 Miscellaneous Type I DetailsF 993 86 (2006)25. Materials and Manufacture5.1 Materials:5.1.1 Type I Materials:5.1.1.1 Pipe ClampIndicate diameter, similar to PracticeF 708, Fig. 1, mater

15、ial specified by grade.5.1.1.2 Ring LinkSize to be not less than clearance shownin Practice F 708, Table 3, Column F, material specified bygrade.5.1.1.3 Common Wire Strand316-in. diameter, sevenstrands of seven wires each, stainless steel, SpecificationA 492, Alloy 316.5.1.1.4 Tiller Rope Clamp316-i

16、n. cable size, manufac-turer, stainless steel (optional).5.1.1.5 Rigid Eye Spring Hook58-in. eye diameter,12-in.snap opening, plated forged steel, Specification A 668/A 668M, Class D.5.1.1.6 SleeveSwaging, oval, for316-in. diameter wirerope, copper.5.1.2 Type II Materials:5.1.2.1 Modified Pipe Clamp

17、Indicate diameter, similar toPractice F 708, Fig. 1, material specified by grade.5.1.2.2 Flat Head Rivet14-in. nominal size, ANSI B18.1,material specified by grade.5.1.2.3 Single Acting Quick Release Pin14-in. nominalsize by510-in. grip, stainless steel, Specification A 167, Type316.5.1.2.4 LanyardW

18、ire rope,18-in. diameter, seven strandsof seven wires each, 12 in. long, stainless steel SpecificationA 492, Alloy 316.5.1.2.5 SleeveSwaging, oval, for18-in. diameter wirerope, copper.5.1.2.6 Lanyard ClipFlatbar,116 in. thick by 1 in. wide by112 in. long, stainless steel, Specification A 167, Alloy

19、316.5.1.2.7 Lever ArmSize to suit, 16-gage material specifiedby grade.5.1.3 Type III Materials:5.1.3.1 PlateIndicate size, 16 gage, material specified bygrade.5.1.3.2 Single-Acting Quick Release Pin14-in. nominalsize by12-in. grip, stainless steel, Specification A 167, Type316.5.1.3.3 LanyardWire ro

20、pe,18-in. diameter, seven strandsof seven wires each, 12 in. long, stainless steel, SpecificationA 492, Alloy 316.5.1.3.4 SleeveSwaging, oval, for18-in. diameter wirerope, copper.5.1.3.5 Lanyard ClipFlatbar,116 in. thick by 1 in. wide by112 in. long, stainless steel, Specification A 167, Alloy 316.5

21、.1.3.6 Lockbar78 in. wide by length to suit by116 in.thick, material specified by grade.5.2 Manufacture:5.2.1 Edges of the locking device shall be smooth. Thedevices shall also be free of defects and burrs.5.2.2 Welds shall be done in accordance with AmericanWelding Society D1.1.6. General Requireme

22、nts General Requirements6.1 A label plate shall be installed on or near the lockingdevice to instruct the operator on usage.6.2 When noise reduction is necessary, the contacting partsof the locking device shall have a rubber coating or lining.6.3 The locking device must be able to lock the valve inb

23、oth the fully opened and completely closed positions.6.4 When using Type I, the cable shall be installed suffi-ciently tight to prevent more than slight movement of thehandwheel in a direction opposite of the designed position butnot so tight as to place the cable in tension.FIG. 3 Type IIHandwheel

24、LatchF 993 86 (2006)36.5 The position of the locking device on the handwheelshall be as to resist movement of the valve stem.6.6 Type II dimensions shall be used to determine the size ofthe lever arm, extension on pipe hanger, and the position of thelocking holes and slot.6.7 When specified by the p

25、urchaser, a padlock can be usedinstead of the quick release pin or spring hook.7. Dimensions and Tolerances7.1 Dimensions shall be as specified in the figures shown.7.2 Tolerances are 6116 in. except for drilled hole diameterfor pin which shall be +132 in., 0 in.8. Keywords8.1 locking device; marine

26、 technology; ship; valve; valvelocking deviceFIG. 4 Miscellaneous Type II DetailsF 993 86 (2006)4FIG. 5 Type IIIValve Cover BoxF 993 86 (2006)5ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of th

27、is standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five ye

28、ars andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical commi

29、ttee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 993 86 (2006)6