ASTM F685-1996(2011) Standard Practice for Determining Toner Usage Efficiency and Dusting Nonheat Fixing Copiers Using Single-Component Toner Systems《测定在使用单一成分调色剂系统的非加热固定复印机中调色剂的使用.pdf

《ASTM F685-1996(2011) Standard Practice for Determining Toner Usage Efficiency and Dusting Nonheat Fixing Copiers Using Single-Component Toner Systems《测定在使用单一成分调色剂系统的非加热固定复印机中调色剂的使用.pdf》由会员分享，可在线阅读，更多相关《ASTM F685-1996(2011) Standard Practice for Determining Toner Usage Efficiency and Dusting Nonheat Fixing Copiers Using Single-Component Toner Systems《测定在使用单一成分调色剂系统的非加热固定复印机中调色剂的使用.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F685 96 (Reapproved 2011)Standard Practice forDetermining Toner Usage, Efficiency, and Dusting NonheatFixing Copiers Using Single-Component Toner Systems1This standard is issued under the fixed designation F685; the number immediately following the designation indicates the year of orig

2、inaladoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the determination of toner usage,efficiency

3、 of toner deposition on an imaged copy, and dustingin those nonheat fixing copiers utilizing a single-componenttoner.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priat

4、e safety and health practices and determine the applica-bility of regulatory limitations prior to use. See Section 8 and10.19.2 for specific precautions and warnings.2. Referenced Documents2.1 ASTM Standards:2F335 Terminology Relating to Electrostatic ImagingF875 Test Method for Evaluation of LargeA

5、rea Density andBackground on Office Copiers2.2 ASTM Adjuncts:Density Target Test Sheets33. Descriptions of Terms Specific to this Standard3.1 single-component toneralso described commerciallyas single-component developer.3.2 toner usageamount of toner (milligrams per copy)removed from the toner hopp

6、er during the copying process.3.3 effciencythe ratio of the weight of toner developed onthe image copy to the weight of the toner used.3.4 toner dustingloss of toner other than to the imagedcopies and therefore the difference between toner usage and theweight of the toner developed on the imaged cop

7、y. Dusting isusually found deposited either inside the copier componentssuch as cleaning subsystems and filters or surrounding thecopier externally, specifically the table top, wall, and so forth.4. Summary of Practice4.1 Afull roll or quantity of sheets together with a sample oftoner are both weigh

8、ed and placed into a copier. Copies areimaged to a predetermined end point and weighed. Tonerusage, dusting, and copier efficiency are subsequently calcu-lated from values obtained from the imaged copy weights andinitial toner weights.5. Significance and Use5.1 Many dry electrostatic developers cons

9、ist of toners andcarriers and only the toner portion of which forms the visibleimage on the copy. Single-component toner (or developer)does not contain a carrier, and in theory, when properly used,is consumed at a rate proportional to the image area anddensity. As with all dry developers, single-com

10、ponent toners(or developers) are not 100 % efficient. Some toner is lost tothe surroundings (inside or outside of the copiers). This loss isalso dependent on copier adjustments and may be significantenough to affect the total number of copies capable of beingproduced by a specific amount of toner.6.

11、 Apparatus6.1 Balance,4capable of a precision of 60.1 g and readableto 0.1 g.6.2 Model Copier, operated in accordance with the manu-facturers instructions.7. Reagents and Materials7.1 A supply of specified type or lot of appropriate papersufficient to complete the test.7.2 A supply of recommended ty

12、pe or lot of dry single-component toner sufficient to complete the test.1This practice is under the jurisdiction of ASTM Committee F05 on BusinessImaging Products and is the direct responsibility of Subcommittee F05.04 onElectrostatic Imaging Products.Current edition approved Oct. 1, 2011. Published

13、 March 2012. Originallyapproved in 1980. Last previous edition approved in 2006 as F68596 (2006). DOI:10.1520/F0685-96R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, ref

14、er to the standards Document Summary page onthe ASTM website.3Available from ASTM International Headquarters. Order Adjunct No.ADJF0875.4A Mettler P5N balance (or equivalent alternative) has been found acceptableand has a reported precision of 60.05 g.1Copyright ASTM International, 100 Barr Harbor D

15、rive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.3 A black target larger than the size of the test target theuser elects to use.8. Precautions8.1 This procedure is not applicable to those single compo-nent toner copiers utilizing either heat or a combination ofpressure and heat f

16、ixing methods because of the possibleweight loss of the paper due to the heat fixing.8.2 If any jams or paper roll splices are encountered duringthis procedure, the test should be discontinued and repeated.8.3 During this procedure, all copier conditions, specificallyline voltage, should be held con

17、stant.8.4 The user should be aware that variables such as relativehumidity, supplies (between lots, within lots, or manufacturersof), copiers, or the interaction of the variables can alter the finalresults.9. Calibration and Standardization9.1 All supplies to be utilized should be preconditioned tot

18、he Technical Association of the Pulp and Paper Industry(TAPPI) conditions of 23.0 6 1.0C and 50.0 6 2.0 % relativehumidity for 24 h prior to evaluation. Evaluate this test underthose same conditions.10. Procedure10.1 Clean the copier and empty the toner from the tonerhopper by any suitable means.10.

19、2 Remove any residual toner within the copier, load thecopier with the appropriate paper, and copy the black test targetuntil the imaged copies are substantially free of toner.10.3 Distribute a weighed sample of toner (40 to 50 6 0.1g) in the hopper. If the mechanics of the copier permit, coverthe h

20、opper with an appropriately cut sheet (or equivalent).Record the weight of the toner. Note the amount (height) oftoner in the hopper as this influences the results.10.4 Place or insert a suitable test target (configuration isleft to the discretion of the evaluator, refer to Note 1) into thecopier an

21、d image several copies. Set the exposure dial for theoptimum copy (the best possible contrast between the back-ground and image). The area of image coverage must beconstant for comparable results.NOTE 1The Test Method F875 adjunct/Test Target for Office Copiersis available.310.5 Image a number of co

22、pies until the copies start to showcopy image deterioration due to the initial exhaustion of thetoner (the images will start to be broken up or incompletelyreproduced). Record the number of copies. All copies shouldbe of the same length and width throughout this test.10.6 Image the black test target

23、 until the imaged copies aresubstantially free of toner. In some copiers this may appear asa background-free area in the center of the imaged copy withtoner deposits along the edge of the copy running in themachine direction. (This end point requires some judgment andmay vary from one copier type to

24、 another.)10.7 Remove the paper supply from the copier and weigh to60.1 g the TAPPI conditioned paper. Record this weight as W1.NOTE 2A variance of 60.1 g is based on the paper supply weighingat least 1000 g. The weight limit of the Mettler P5N balance is 6000 gmaximum.10.8 Weigh a sample of dry sin

25、gle-component toner to60.1 g approximately equal to the amount weighed in 10.3 anddistribute this weighed sample equally in the hopper. Recordthis weight as W2.NOTE 3The user may wish to alter the recommended toner weightsample to suit his test requirements.10.9 Set the exposure dial for the optimum

26、 copy (as foundin 10.4) and insert or place the same test target as used in 10.4into the copier.10.10 Load the conditioned paper supply into the copier.10.11 Image a number N of copies. N should approach butnot exceed the number of copies required to show copy defectsdue to the exhaustion of toner (

27、refer to 10.5). Remove the papersupply from the copier.10.12 Weigh all N copies plus the remainder of the papersupply just removed from the copier. Record the weight as W3.10.13 Calculate the weight of toner W4on N copies by:W45 W32 W1(1)10.14 Remove N copies from the balance and weigh theremainder

28、of the paper and record as W5. Count the number ofN copies and record.10.15 Return the paper to the copier and image the blacktest target until the same endpoint is reached as found in 10.6.Record the copies required to do this as N8. Remove theremaining paper from the copier.10.16 Weigh the copies

29、from 10.15 plus the remainingpaper. Record as weight W6.10.17 Calculate the weight of toner W7on the copiesobtained from 10.15 by:W75 W62 W5(2)10.18 Calculate the total weight of toner W8put on allimaged copies by:W85 W71 W4(3)10.19 Since passage of the paper through the copier maycause a weight cha

30、nge due to a gain or loss of moisture, a blankdetermination should be carried out as described in thefollowing:10.19.1 Weigh the unimaged paper from 10.16 and recordthe weight as W10. This paper supply should contain enoughpaper to yield approximately 200 copies.10.19.2 Empty the toner hopper and di

31、sconnect the corona.(WarningUnplug the machine first.)10.19.3 Using an all-white original, process approximately200 copies through the completely clean copier. Count thenumber of copies made and record as n.10.19.4 Weigh the copies and the remainder of the unim-aged paper and record this weight as W

32、11.10.19.5 Calculate the paper weight change per copy (W12)by the following:W125 W102 W11!/n (4)F685 96 (2011)211. Calculation11.1 Effciency:E 5 W81 N 1 N8!W12!/W2(5)Refer to 10.15 for N8.11.2 Toner Usage or Consumption:U 5 W41 NW12!/NE (6)Refer to 10.14 for N.11.3 Toner Dusting:D 5 U1$ E! (7)12. Re

33、port12.1 Report all test conditions (temperature and humidity),toner and paper lot number designations if available, and allmeasured and calculated weights. The report must include thetarget used.13. Keywords13.1 development efficiency; non-heat fixing; single-component toner; toner dusting; toner u

34、sageASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights,

35、 are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional sta

36、ndardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Com

37、mittee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F685 96 (2011)3