ASTM F1933-1998(2004) Standard Specification for Illustrating the Footprint of a Backpacking or Mountaineering Tent《插图说明背包式或登山用帐蓬触地面积的标准规范》.pdf

《ASTM F1933-1998(2004) Standard Specification for Illustrating the Footprint of a Backpacking or Mountaineering Tent《插图说明背包式或登山用帐蓬触地面积的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1933-1998(2004) Standard Specification for Illustrating the Footprint of a Backpacking or Mountaineering Tent《插图说明背包式或登山用帐蓬触地面积的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1933 98 (Reapproved 2004)An American National StandardStandard Specification forIllustrating the Footprint of a Backpacking orMountaineering Tent1This standard is issued under the fixed designation F 1933; the number immediately following the designation indicates the year oforiginal

2、adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements for illustratingthe floorpla

3、n, and marking of tents for use in the sports ofbackpacking and mountaineering.1.2 The values stated in inch-pound units are to be regardedas the standard.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 footprint, nthe size of the tent floor illustratedgraphically as a scaled

4、and dimensioned outline.2.1.2 tent, na portable shelter made primarily of fabricweighing less than 3 oz/yd2, designed to be carried by theoccupants while backpacking or mountaineering.3. Product Marking3.1 Markings, if included in the tent or marketing literature,shall be presented as follows:3.1.1

5、Graphic illustrations of the footprint shall be accu-rately scaled by the same percentage in both length and width.At a minimum, two dimensions, preferably at 90 to each other,shall be provided. Lengths shall be shown to the nearest wholeinch (centimetre). Angles shall be shown to the nearest 5 (see

6、Fig. 1).3.1.2 Graphic illustrations of sleeping bags and pads shallbe scaled to the footprint and may be included in the floorplanillustration assuming they conform to the following:3.1.2.1 Sleeping bags for adults must measure 80 in. inlength. The width at the shoulder must be 24 in., and the width

7、at the foot no less than 16 in., and3.1.2.2 Full length sleeping pads must measure 72 by 20 in.3.1.3 Markings, if included in the tent or marketing litera-ture, shall reference this specification.4. Keywords4.1 backpacking and mountaineering; floorplan size; tents1This specification is under the jur

8、isdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.22 onCamping Softgoods.Current edition approved May 1, 2004. Published May 2004. Originallyapproved in 1998. Last previous edition approved in 1998 as F 1933 - 98.NOTE 1Scale =125FI

9、G. 1 ExampleGraphic Illustration of the Footprint1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this

10、standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be r

11、eviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespon

12、sible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West

13、 Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 1933 98 (2004)2