ASTM F1667-2011a Standard Specification for Driven Fasteners Nails Spikes and Staples《钉子 长钉和U型钉等锲入式紧固件的标准规格 》.pdf
《ASTM F1667-2011a Standard Specification for Driven Fasteners Nails Spikes and Staples《钉子 长钉和U型钉等锲入式紧固件的标准规格 》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1667-2011a Standard Specification for Driven Fasteners Nails Spikes and Staples《钉子 长钉和U型钉等锲入式紧固件的标准规格 》.pdf(46页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1667 11aStandard Specification forDriven Fasteners: Nails, Spikes, and Staples1This standard is issued under the fixed designation F1667; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A nu
2、mber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense. The Commercial and Government Entity (Cage)Code for ASTM: 81346.1.
3、Scope*1.1 This specification covers nails, spikes, staples, and otherdriven fasteners, as listed in Table 1.NOTE 1Fastener ductility information is presented in Table 2 anddimensional information in Tables 3-65.1.2 Fasteners described in this specification are driven byhand tool, power tool, or mech
4、anical device in single ormultiple strikes and are positioned by hand, tool, or machine.1.3 The values stated in inch-pound units are to be regardedas standard. No other units of measurement are included in thisstandard.1.4 Fasteners in this specification are sold in bulk (loose)form and are collate
5、d for loading into the magazine of anapplication tool. Other than as covered in Section 9, Workman-ship, cohering materials (including, but not limited to, plastic,adhesive bond, paper tape, plastic strip, plastic carrier, wire,etc.) and relative orientation of collated fasteners are not withinthe s
6、cope of this standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior
7、to use.2. Referenced Documents2.1 ASTM Standards:2A153/A153M Specification for Zinc Coating (Hot-Dip) onIron and Steel HardwareA510M Specification for General Requirements for WireRods and Coarse Round Wire, Carbon Steel (Metric)A641/A641M Specification for ZincCoated (Galvanized)Carbon Steel WireB6
8、95 Specification for Coatings of Zinc Mechanically De-posited on Iron and SteelF547 Terminology of Nails for Use with Wood and Wood-Base MaterialsF592 Terminology of Collated and Cohered Fasteners andTheir Application ToolsF680 Test Methods for NailsF1575 Test Method for Determining Bending Yield Mo
9、-ment of Nails3. Terminology3.1 DefinitionsThe definitions used in this specificationare those of common commercial acceptance and usage andalso appear in Terminologies F547 and F592.4. Classification4.1 The fasteners and their Table 1 classification are iden-tified as follows:NOTE 2The identificati
10、on of fasteners, classified by style and type(alpha indicators) followed by a dash number (numerical code) based onTables 3-65, identifies dimensions specifically and establishes a PIN (partidentifying number) system when preceded by the F1667 ASTM desig-nator of this specification. For example:4.2
11、The trade designation, S, pennyweight, used in commer-cial practice is referenced in Tables 3-64 wherever it applies.5. Ordering Information5.1 Orders for driven fasteners under this specification shallinclude the following information:5.1.1 Quantity or weight;1This specification is under the jurisd
12、iction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.05 on Driven andOther Fasteners.Current edition approved Nov. 1, 2011. Published November 2011. Originallyapproved in 1995. Last previous edition approved in 2011 as F1667 11. DOI:10.1520/F1667-11A.2For ref
13、erenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Co
14、pyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.2 Part identifying number (PIN) or product description(see 4.1 and appropriate table);5.1.3 Special material requirements, if specified, includingcoatings or finishes;5.1.4 ASTM design
15、ation;5.1.5 Packaging requirements;5.1.6 A producers or suppliers certification that the mate-rial and the finished fastener are in compliance with thisspecification, furnished only when specified in the purchaseorder;5.1.7 Supplementary requirements, if any; and5.1.8 Any additions agreed upon betwe
16、en the purchaser andthe supplier.6. Material Requirements6.1 Steel wire used in the manufacture of driven fastenersshall be of low carbon, medium-low carbon, or medium-highcarbon.6.2 Stainless steel wire used in the manufacture of drivenfasteners shall be of Types 302, 304, 305, or 316.6.3 Carbon st
17、eel wire for the manufacture of hardened steelnails shall be suitable for heat treatment to a minimumhardness of 37 HRC.6.4 Sheet steel used in the manufacture of cut nails (Type II)and cut spikes (Type III) shall be a medium-carbon sheet steel.6.5 Copper used in the manufacture of driven fasteners
18、shallcontain a minimum of 98 % pure copper.6.6 Copper-clad steel wire used in the manufacture ofdriven fasteners shall contain not less than 20 % copper byweight. The average thickness of copper on the steel wire shallbe not less than 10 % of the radius of the clad wire; theminimum thickness of copp
19、er on the steel wire shall be not lessthan 8 % of the radius of the clad wire.6.7 Aluminum alloy wire used in the manufacture of fas-teners shall conform to Alloy 2024, 5056, 6061, or 6110 andhave a minimum ultimate tensile strength of 60 000 psi.NOTE 3Smooth shank nails are sometimes chemically tre
20、ated toremove grease, oil, and foreign matter and to roughen the surfacemicroscopically. Mechanically deformed nails are sometimes cleaned toremove grease and foreign matter.6.8 Brass wire used in the manufacture of fasteners shall beof good commercial quality suitable for the purpose.7. Physical Pr
21、operties7.1 DuctilityThe fasteners shall be sufficiently ductile towithstand cold bending without fracture, as specified in Table2 for various materials used in the manufacture of fastenersutilizing the conventional bend test described in Test MethodsF680. Mandrel diameter used in this test shall no
22、t exceednail/wire diameter. The cold bend test shall not apply tounhardened nails with deformed shanks.TABLE 1 Classification and Identification IndexType Style Style Identification TableINails (NL) 1. Brads BR 32. Barrel BL 43. Boat BTH/BTL 54. Box A BXA 6Box B BXB 75. Broom BM 86. Casing CN 97. Co
23、oler CL 108. Sinker SK 119. Corker CK 1210. Common CMA 13Common CMC 14Common CMS 15Common CMM 1611. Concrete CTS/CTM 1712. Double-headed DH 1813. Fine FN 1914. Finishing FH 2015. Flooring FL 2116. Lath LHF 22Lath LHH 2317. Masonry MR/MRH 2418. Pallet PL 2519. Gypsum wallboard GWS 26Gypsum wallboard
24、GWM 2720. Roofing RFA 28Roofing RFS 29Roofing RFC 30Roofing RFL 31Roofing RFR 32Roofing RFD 33Roofing RFNS/RFND 3421. Shingle SHAD/SHAS 35Shingle SHSS/SHNSB 3622. Siding SDF/SDC/SDK 3723. Slating SLA/SLC/SLS 3824. Rubber heel RH 3925. Underlayment UL 4026. Square-barbed SB 4127. Masonry drive MD 422
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF16672011ASTANDARDSPECIFICATIONFORDRIVENFASTENERSNAILSSPIKESANDSTAPLES 钉子 长钉 锲入式 紧固 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-535358.html