ASTM F1136 F1136M-2011 Standard Specification for Zinc Aluminum Corrosion Protective Coatings for Fasteners《紧固件防腐锌 铝涂料的标准规范》.pdf
《ASTM F1136 F1136M-2011 Standard Specification for Zinc Aluminum Corrosion Protective Coatings for Fasteners《紧固件防腐锌 铝涂料的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1136 F1136M-2011 Standard Specification for Zinc Aluminum Corrosion Protective Coatings for Fasteners《紧固件防腐锌 铝涂料的标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1136/F1136M 11Standard Specification forZinc/Aluminum Corrosion Protective Coatings forFasteners1This standard is issued under the fixed designation F1136/F1136M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the ye
2、ar of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the basic requirements forwater-based zinc/aluminum dispersion inorganic basecoats an
3、doptional sealers and topcoats for fasteners. The basecoat cancontain chrome (C) or be non-chrome (NC).1.2 These coatings are applied by conventional dip-spin,dip-drain, or spray methods to ferrous parts which can behandled through a cleaning, coating, and baking operation, andwhich are not adversel
4、y affected by baking temperatures up to330C 626F.1.3 The coating process does not induce the possibility ofinternal hydrogen embrittlement providing that the fastenershave not been cleaned or pre-treated with an acid or phosphate.Alkaline cleaning or vapor degreasing is required along withshot blast
5、ing to remove rust or scale.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may re
6、sult in non-conformancewith the standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory
7、 limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusD610 Practice for Evaluating Degree of Rusting on PaintedSteel SurfacesD3359 Test Methods for Measuring Adhesion by Tape TestF606 Test Methods for Determining the Mechanical Pro
8、p-erties of Externally and Internally Threaded Fasteners,Washers, Direct Tension Indicators, and RivetsF606M Test Methods for Determining the MechanicalProperties of Externally and Internally Threaded Fasteners,Washers, and Rivets (Metric)F1624 Test Method for Measurement of Hydrogen Em-brittlement
9、Threshold in Steel by the Incremental StepLoading TechniqueF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance InspectionF1624 Test Method for Measurement of Hydrogen Em-brittlement Threshold in Steel by the Incremental StepLoading TechniqueF1789 Terminology for
10、 F16 Mechanical FastenersF1940 Test Method for Process Control Verification toPrevent Hydrogen Embrittlement in Plated or CoatedFasteners3. Classification3.1 These coatings are classified into six grades according tothe requirements in Table 1.3.1.1 Grade 1 requires a minimum basecoat thickness of4m
11、 16g/m2 or 0.16 mil (0.052 oz/ft2). This is usuallyapplied in two coats to bulk parts, or one coat to racked parts.No topcoat is applied in Grade 1.3.1.2 Grade 2 requires a minimum basecoat thickness of5m 20 g/m2 or 0.20 mil (0.066 oz/ft2). This is usuallyapplied in two coats to bulk parts, or one c
12、oat to racked parts.No topcoat is applied in Grade 2.3.1.3 Grade 3 requires a minimum basecoat thickness of5m 20 g/m2 or 0.20 mil (0.066 oz/ft2) and a single coat ofthe clear sealer. The sealer provides additional corrosionprotection and greater lubricity than Grade 2.3.1.4 Grade 4 requires a minimu
13、m basecoat thickness of8m 28 g/m2 or 0.31 mil (0.092 oz/ft2). This is usuallyapplied in three coats to bulk parts, or one to two coats toracked parts. No topcoat is applied in Grade 4.3.1.5 Grade 5 requires a minimum basecoat thickness of5m 20 g/m2 or 0.20 mil (0.066 oz/ft2) and a single coat ofthe
14、lubricated sealer. The sealer provides additional corrosionprotection than Grade 2 and greater lubricity than Grade 3.1This specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.03 on Coatings onFasteners.Current edition approv
15、ed Nov. 1, 2011. Published December 2011. Originallyapproved in 1988. Last previous edition approved in 2010 as F113610. DOI:10.1520/F1136_F1136M-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStanda
16、rds volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.6 Grade 6 requires a minimu
17、m basecoat thickness of5m 20 g/m2 or 0.20 mil (0.066 oz/ft2) with variouspigmented topcoats applied. The topcoats can be black orvarious other colors.4. Ordering Information4.1 Orders for parts under this specification shall include thefollowing information:4.1.1 Quantity of parts,4.1.2 Grade of coa
18、ting as given in Table 1,4.1.3 Specify chrome (C) or non-chrome (NC). Unlessotherwise specified, coating to this specification will be sup-plied with chrome,4.1.4 4 For Grade 6, specify the type of topcoat (that is,Grade 6; Black, Type X), and4.1.5 Any additions to the specification as agreed uponbe
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF1136F1136M2011STANDARDSPECIFICATIONFORZINCALUMINUMCORROSIONPROTECTIVECOATINGSFORFASTENERS 紧固 防腐

链接地址:http://www.mydoc123.com/p-534253.html