ASTM E2129-2018 Standard Practice for Data Collection for Sustainability Assessment of Building Products.pdf

《ASTM E2129-2018 Standard Practice for Data Collection for Sustainability Assessment of Building Products.pdf》由会员分享，可在线阅读，更多相关《ASTM E2129-2018 Standard Practice for Data Collection for Sustainability Assessment of Building Products.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2129 18Standard Practice forData Collection for Sustainability Assessment of BuildingProducts1This standard is issued under the fixed designation E2129; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last

2、 revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a set of instructions for collectingdata to be used in assessing the sustainability of buildingproduc

3、ts for use in both commercial and residential buildings.1.1.1 There are many features of a building that contributeto sustainability; one of them is the selection of products foruse in a building. Other key features influencing sustainabilityinclude, but are not limited to: overall efficiency of the

4、 designof the building, the impact the building has on the habits of theoccupants, and the impact the building has on the microclimateand macroclimate. This practice addresses sustainability issuesrelated to building products. This practice does not addresssustainability issues related to overall bu

5、ilding design, siteselection, building operations, or other features influencingsustainability.1.1.2 While it is recommended that users rely on profes-sional judgment informed by both environmental expertise andspecific knowledge of the intended use of the product, thispractice provides no instructi

6、on as to interpretation of the dataobtained. Interpretation of the data obtained is the responsibil-ity of the user of this practice.1.1.3 This document cannot replace education or experienceand should be used in conjunction with professional judgment.Not all aspects of this practice may be applicab

7、le in allcircumstances. This practice is not intended to represent orreplace the standard of care by which the adequacy of a givenprofessional service must be judged, nor should this documentbe applied without consideration of a projects many uniqueaspects. The word “standard” in the title means onl

8、y that thedocument has been approved through the ASTM consensusprocess.1.2 This practice is organized according to the ConstructionSpecifications Institutes (CSI) MasterFormat2sections to pro-mote consistency in the evaluation of building products.1.2.1 CSI MasterFormat version 1995 is used to organ

9、izeinformation in Table 2. Appendix X1 provides a cross refer-ence comparison to CSI MasterFormat 2004.1.3 This practice includes general, comprehensive datarequirements. Depending upon the building product, certaindata requirements may not apply given the unique character-istics of the product and

10、the potential environmental impactsrelated to the intended use of the product. Depending upon thebuilding product, certain data requirements may need to beadded as appropriate to the unique characteristics of theproduct and the potential environmental impacts related to theintended use of the produc

11、t.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to u

12、se.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers

13、 to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3C618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC989/C989M Specification for Slag Cement for Use inConcrete and MortarsC1240 Specification for Silica Fume Used in CementitiousMixturesD5359

14、 Specification for Glass Cullet Recovered from Wastefor Use in Manufacture of Glass FiberD6400 Specification for Labeling of Plastics Designed to beAerobically Composted in Municipal or Industrial Facili-ties1This practice is under the jurisdiction of ASTM Committee E60 on Sustain-ability and is the

15、 direct responsibility of Subcommittee E60.01 on Buildings andConstruction.Current edition approved June 1, 2018. Published June 2018. Originallyapproved in 2001. Last previous edition approved in 2010 as E2129 10. DOI:10.1520/E2129-18.2The term “MasterFormat” and the MasterFormat logo are trademark

16、s ofConstruction Specifications Institute (CSI).3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright AST

17、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Stan

18、dards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1TABLE 1 General QuestionsQuestion Yes or No N/A U/K CommentsDIVISION 1GENERAL REQUIREMENTSCriterion No. 1Materials (Product Feedstock)1.1 Have efforts (such as mining management, sit

19、e restoration, and so forth) been made tominimize or avoid negative environmental impacts, or both, (such as impact to rare orendangered resources or species, releases of toxic chemicals or hazardous airpollutants, and so forth) in obtaining raw materials for this product? If yes, describethese effo

20、rts.1.2 Is the product a recycled content product? If YES, indicate what percentage of theproduct is recycled and differentiate between pre-consumer and post-consumerrecycled content.1.3 If applicable, does the recycled content product contain the percentage of recoveredmaterials recommended by the

21、United States Environmental Protection Agencys (EPA)Comprehensive Procurement Guidelines?1.4 Is the product 100% recyclable? If NO, please indicate what percentage of the productis recyclable.1.5 Is the product a biobased product (that is, agricultural or forestry material)? If YES,please indicate t

22、he source and biobased content percentage. If percentage refers to acomponent rather than the entire product, please specify.1.6 Is the product made from a renewable resource? If YES, indicate the renewable cycletime and what percentage of the product that resource represents.1.7 Does the product, i

23、n the specified condition of use, meet U.S. EPAs National Vola-tile Organic Compound (VOC)?1.8 Does the product in the specified condition of use, meet the requirements ofSouth Coast Air Quality Management District for content of VOCs?1.9 Is this product covered by an environmental product declarati

24、on (EPD) that conforms toISO 14025, ISO 14040, ISO 14044, and EN 15804 or ISO 21930 and does it have atleast a cradle-to-gate scope? If YES, please indicate if EPD is product specific and howthe sender of this questionnaire could obtain a copy of the EPD.Criterion No. 2Manufacturing2.1 Has the manuf

25、acturer taken steps to minimize the use of nonrenewable energy fromthe point at which raw materials are gathered to the point at which the final product istransported to the building site? If yes, describe these measures.2.2 Is any of the waste produced in making this product reclaimed on-site? If y

26、es, whatpercentage of the waste is reclaimed? Of the waste that is not reclaimed on-site, howis that waste handled?2.3 Does the process for manufacturing this product avoid the use of listed substancesabove the levels that would require reporting under the U.S. EPAs Toxics Release In-ventory?AIf NO,

27、 indicate how much of each substance is released per unit of product.2.4a Does the process for manufacturing the product avoid the addition of substances listedin the National Toxicology Programs (NTP) Report on Carcinogens?B2.4b If substances listed in the NTPs Report on Carcinogens are added direc

28、tly in themanufacturing process or are reported by suppliers on Material Safety Data Sheets(MSDS), do the concentrations fall below levels required to be reported under federalregulations on the products MSDS? If NO, indicate the substance, classification andconcentration per unit of product.2.5 Hav

29、e any recent improvements been made to limit negative environmental impacts re-lating to the manufacturing process? If YES, describe the benchmark against which theimprovements are measured and the degree of improvement.2.6 If water is used during the production process, have water conservation or r

30、ecyclingmeasures, or both, been initiated? If yes, describe the measures and what percentageof the total water usage they address.2.7 Has the manufacturer undertaken any of the following actions? If yes, indicate whenthe action(s) was (were) taken and describe the benchmark against which the improve

31、-ments are measured and the degree of improvement.2.7a Redesigned a production process to decrease greenhouse gas emissions?2.7b Redesigned a production process to decrease liquid effluents?2.7c Redesigned a production process to utilize less toxic materials?2.7d Substituted safer solvents in a prod

32、uction process?2.7e Instituted more stringent dust controls?2.7f Installed smoke-stack particulate collectors or gas scrubbers?2.7g Installed or improved in-plant solid and toxic waste reduction programs?2.8 Does the manufacturing facility comply with or exceed applicable occupational, health,and sa

33、fety requirements?Criterion No. 3Operational Performance of Installed Product3.1 If applicable, does the product qualify for an EPA ENERGY STARCProgram rating ormeet the energy efficiency recommendations of the Department of Energys (DOE)Federal Energy Management Program?D3.2 Describe the products e

34、nergy efficiency impacts.3.3 Describe routine maintenance procedures for the product.3.4 How long will the product last in the building if maintained properly with routine mainte-nance procedures?3.5 Does the manufacturer provide detailed instructions with the product upon delivery tothe job site fo

35、r the proper use and maintenance required in order to ensure that thisproduct will last this long?E2129 182E631 Terminology of Building ConstructionsE1480 Terminology of Facility Management (Building-Related)E2114 Terminology for Sustainability Relative to the Perfor-mance of Buildings2.2 ANSI Stand

36、ard:4ANSI A208.2 Medium Density Fiberboard2.3 ASHRAE Standards:5ASHRAE 90.1 Energy Efficient Design of New BuildingsExcept Low-Rise Residential BuildingsASHRAE 62 Ventilation for Acceptable Indoor Air QualityASHRAE 5276 Gravimetric and Dust-Spot Procedures forTesting Air-Cleaning Devices Used in Gen

37、eral Ventilationfor Removing Particulate Matter2.4 ASME Standard:6ASME A112.18.1M-1989 Plumbing Fixture Fittings2.5 CSI Program:7MasterFormat 2004 Edition2.6 EN Standard:8EN 15804 (2012 Amd 1) Sustainability of constructionworks - Environmental product declarations - Core rulesfor the product catego

38、ry of construction products2.7 EPA Standards:9ENERGY STAR ProgramComprehensive Procurement GuidelinesNational Volatile Organic Compound (VOC) EmissionStandards2.8 HUD Standards:1024 CFR Pt. 3280 Manufactured Home Construction andSafety Standards4Available from American National Standards Institute (

39、ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from American Society of Heating, Refrigerating, and Air-Conditioning Engineers, Inc. (ASHRAE), 1791 Tullie Circle, NE, Atlanta, GA30329, http:/www.ashrae.org.6Available from American Society of Mechanical Engineers (

40、ASME), ASMEInternational Headquarters, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.7Available from Construction Specifications Institute (CSI), 110 S. Union St.,Suite 100, Alexandria VA 22314, http:/www.csiresources.org.8Available from European Standards (EN), Krimicka 134, 318 13 Pil

41、sen, CzechRepublic, https:/www.en-standard.eu.9Available from U.S. Environmental Protection Agency (EPA), William Jeffer-son Clinton Bldg., 1200 Pennsylvania Ave., NW, Washington, DC 20460, http:/www.epa.gov.10Available from U.S. Department of Housing and Urban Development (HUD),451 7th Street S.W.,

42、 Washington, DC 20410, http:/www.hud.gov.TABLE 1 ContinuedQuestion Yes or No N/A U/K CommentsCriterion No. 4Indoor Environmental QualityE4.1 Is there any other information about how this product contributes to indoorenvironmental quality (positively or negatively, for example, acoustical properties,

43、lighting, potential risks to workers during application, and so forth) that has not alreadybeen reported, but that sender of this questionnaire should know? If YES, describe. (Ifthis product is not intended to be used in the indoor environment or to interface withthe occupants, indicate N/A.)Criteri

44、on No. 5Corporate Environmental Policy5.1 Does the manufacturer have a written environmental policy? If YES, indicate how thesender of this questionnaire could obtain a copy of this policy upon request.5.2 Does the manufacturer have a reclamation program or any other program in place tofacilitate th

45、e recycling or reuse of its product by accepting return of the product at theend of its useful life? If NO, comment on the environmental impact of the product as awaste material. If yes, comment on how much of the product is actually reused orrecycled at the end of the products useful life.5.3 Does

46、the manufacturer have a program in place to reduce the amount of the productspackaging? If YES, describe.5.4 Does the manufacturer have a program in place to facilitate the return, reuse, recycling,or composting of the products packaging? If YES, describe.5.5 Does the manufacturer provide informatio

47、n on the service life of the product orencourage the use of professional guidelines to determine the service life of theproduct?5.6 Does the manufacturer provide information regarding natural disaster mitigation, suchas performance of the product during a natural disaster or appropriate response aft

48、er anatural disaster?5.7 Is documentation available to support the products environmental claims? If YES,please indicate how copies may be obtained upon request.5.8 Is there other information, for which you could provide objective evidence, about theenvironmental quality of the building product you

49、offer that you would like taken intoconsideration? If YES, describe the information and indicate how copies of thisevidence could be obtained upon request.AFor additional information, visit http:/www.epa.gov/tri.BNTP (National Toxicology Program). 2016. Report on Carcinogens, Fourteenth Edition.; Research Triangle Park, NC: U.S. Department of Health and Human Services,Public Health Service. https:/ntp.niehs.nih.gov/go/roc14.CThe term “ENERGY STAR” and the ENERGY STAR logo are trademarks of the U.S. Environmental Protection Agency (EPA).DAdditional inform