ASTM E1425-2014 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗户 门 天窗以及玻璃幕墙系统的标准实施规程》.pdf

《ASTM E1425-2014 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗户 门 天窗以及玻璃幕墙系统的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1425-2014 Standard Practice for Determining the Acoustical Performance of Windows Doors Skylight and Glazed Wall Systems《测定窗户 门 天窗以及玻璃幕墙系统的标准实施规程》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1425 07E1425 14Standard Practice forDetermining the Acoustical Performance of Windows,Doors, Skylight, and Glazed Wall Systems1This standard is issued under the fixed designation E1425; the number immediately following the designation indicates the year oforiginal adoption or, in the c

2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice establishes requirements for testing and rating acoustical performance of w

3、indow, door, skylight, and glazedwall systems, regardless of their method or materials of manufacture.1.1.1 Operating force, latching force, and air leakage are integral elements of the acoustical performance of window, door,skylight, and glazed wall systems. This practice requires (when applicable)

4、 the concurrent testing of operating force, latching force,and air leakage, in addition to the sound transmission loss test.1.2 This practice establishes the test methodology, specimen criteria, and classification rating system for purposes ofdetermining the acoustical performance levels of window,

5、door, skylight, and glazed wall systems only, and not through openingsbetween such assemblies and adjacent construction.1.3 The values stated in SIinch-pound units are to be regarded as the standard. The values given in parentheses are forinformation only.mathematical conversions to SI units that ar

6、e provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the appli

7、cability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C634 Terminology Relating to Building and Environmental AcousticsE90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and ElementsE283 Test Method for Determinin

8、g Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under SpecifiedPressure Differences Across the SpecimenE413 Classification for Rating Sound InsulationE631 Terminology of Building ConstructionsE1332 Classification for Rating Outdoor-Indoor Sound AttenuationE2068 Test Method f

9、or Determination of Operating Force of Sliding Windows and Doors2.2 Other Standards:28 CFR Part 36 ADA Standards for Accessible Design3AAMA/WDMA/CSA 101I.S.2A440 Standard Specification for Windows, Doors, and Unit Skylights4,5AAMA 501 Methods of Tests for Exterior Walls4NFRC 100 Procedure for Determ

10、ining Fenestration Product U Factors61 This practice is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.51 on Performanceof Windows, Doors, Skylights and Curtain Walls.Current edition approved Oct. 1, 2007Sept. 1, 2014. Pu

11、blished November 2007September 2014. Originally approved in 1991. Last previous edition approved in 19992007as E1827 91 (1999).E1425 07. DOI: 10.1520/E1425-07.10.1520/E1425-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For

12、 Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA19111-5098, http:/www.dodssp.da

13、ps.mil. 19111-5094, http:/quicksearch.dla.mil.4 Available from the American Architectural Manufacturers Association (AAMA), 1827 Walden Office Square, Suite 550, Schaumburg, Illinois 60173-4268. IL60173-4268, http:/www.aamanet.org.5 Available from Canadian Standards Association (CSA), 5060 Spectrum

14、Way, Mississauga, ON L4W 5N6, Canada, http:/www.csa.ca.6 Available from the National Fenestration Rating Council (NFRC), 6305 Ivy Lane, Suite 140 Greenbelt, MD 20770.20770, http:/www.nfrc.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indica

15、tion of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be con

16、sidered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1ISO 140 AcousticsMeasurement of sound insulation in buildings and of building elements73. Terminology3.1 DefinitionsFor definitions of terms used in this pr

17、actice, refer to Terminologies C634 and E631, unless otherwiseindicated.4. Significance and Use4.1 Air Leakage Relative to Sound TransmissionCertain frequencies are more susceptible to sound transmission throughcavities or discontinuities in the test specimen; therefore, the air leakage of the test

18、specimen is reported to allow the approvingauthority information relative to air tightness.NOTE 1The AAMA/WDMA/CSA 101 I.S.2 A440 document provides air leakage acceptance criteria for these products based on their performanceclass. Acoustical products could require a lower air leakage rate than what

19、 is required in this standard in order to achieve the desired acousticalperformance.4.2 Operating Force Relative to Sound TransmissionThe use of specific sealing components to achieve a given sound ratingcould affect operating force of the vertical or horizontal sliding sash or panels of the assembl

20、y; therefore, operating force is reportedto allow the approving authority information relative to sash or panel operating forces.NOTE 2The opening force in 28 CFR Part 36 ADA for interior hinged doors and sliding doors is limited to 22.2 N (5 lbf).5 lbf (22.2 N). TheAAMA/WDMA/CSA 101 I.S.2 A440 docu

21、ment provides operating force acceptance criteria for products based on their performance class.4.3 Latching forceForce Relative to Sound TransmissionLatching force can affect the compression of seals and the amountof damping applied to the system that in turn affects the air leakage and the acousti

22、cal performance. The use of specific sealingcomponents and latching/locking hardware can affect the force required to close and latch the door under test. The latching forceis reported to allow the approving authority information relative to sash or panel latching conditions.NOTE 3The AAMA/WDMA/CSA

23、101 I.S.2 A440 document states that the latchingmaximum force shall not exceed 65 N (15 lbf).to latch shall bemeasured and reported.5. Test Specimen5.1 Assemblies to be tested in accordance with this practice shall be representative of those produced by the manufacturer orfabricator. Test specimens

24、shall be sealed, painted or otherwise finished or prepared only as they would normally be prepared foractual installation and use. Test specimens shall be mounted for testing as specified by each applicable test method.5.1.1 Test specimens shall not be modified with supplementary adhesives, sealants

25、, tapes, or clamping devices not normally apart of the product.5.2 The test specimen size for window, door, skylight, and glazed wall systems are listed below in Table 1.The . The window,sliding door, glazed wall system, sloped glazing system, skylight, and roof window test specimen size shall not v

26、ary by more than25 mm (i in.)1 in. (25 mm) for either dimension. The single and double hinged door test specimen width shall not vary by morethan 50 mm (2 in.)2 in. (50 mm) and the height shall not vary by more than 75 mm (3 in.).3 in. (75 mm).6. Test Methods6.1 The sequence of testing shall be: ope

27、rating force (if applicable); followed by latching force (if applicable); followed by airleakage; and ending with sound transmission loss. If additional sash or panels are tested in the same specimen frame, the completesequence of tests shall be repeated for each set of sash or panels. The specimen

28、shall be opened and closed (where applicable) atleast five times prior to conducting the operating, latching force and air leakage tests.6.2 Operating forceForceThe operating force test shall be conducted on horizontal or vertical operating windows andsliding doors in accordance with ASTM E2068. For

29、 dual windows or doors, the operating force shall be measured on both setsof sash or panels. The operating force of rotary operators shall be determined in accordance with the procedures contained in theAAMA/WDMA/CSA 101I.S.2A440 standard.6.2.1 The operating force shall not exceed the maximum force

30、to initiate motion and the maximum force to maintain motioncriteria contained in the AAMA/WDMA/CSA 101I.S.2A440 standard. If adjustments need to be made, the operating force shallbe remeasured.6.3 Latching forceForceLatching force tests shall be conducted on swinging (side-hinged) doors with latches

31、. The latchingforce test shall be conducted in accordance with procedures contained in the AAMA/WDMA/CSA 101I.S.2A440 standard. Formultiple doors, such as dual doors (back to back) or double doors (side by side) the latching force shall be conducted on all panelscontaining latching hardware.7 Availa

32、ble from International Organization for Standardization (ISO), 1 rue de Varemb, Case postale 56, CH-1211,1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva20, Switzerland, http:/www.iso.ch.http:/www.iso.org.E1425 1426.3.1 The maximum latching force shall not exceed the maximum latching force requiremen

33、t be reported as required in theAAMA/WDMA/CSA 101I.S.2A440 standard. If adjustments need to be made, the operating force and latching force must beremeasured.NOTE 4A swinging door is defined as closed when the latch is fully secured in the strike plate and the door remains in the closed position.6.4

34、 Air leakage testLeakage TestThe air leakage test shall be performed in accordance with Test Method E283. The airleakage test pressure for windows, doors, and skylights shall be as specified in theAAMA/WDMA/CSA 101I.S.2A440 standard.The air leakage test for glazed wall and sloped glazing systems sha

35、ll be initially conducted at a test pressure of 75 Pa (1.57 psf)1.57psf (75 Pa) and then at a test pressure 300 Pa (6.24 psf).6.24 psf (300 Pa).TABLE 1 Test Specimen SizeWindow Descriptions Width (mm) Height (mm) Width (in.) Height (in.)basement window 900 600 35.4 23.6casement window 600 1500 23.6

36、59.1compositefixed beside operable 1500 1200 59.1 47.2compositefixed over/under operable 1200 1500 47.2 59.1dual action window (tilt/turn window) 1200 1500 47.2 59.1fixed window (picture window) 1200 1500 47.2 59.1greenhouse/garden window 900 900 300 35.4 35.4 11.8horizontal sliding window 1500 1200

37、 59.1 47.2jalawning window 1200 1500 47.2 59.1jalousie window 1200 1500 47.2 59.1pivoted window (vertical or horizontal) 1200 1500 47.2 59.1projected window (awning or hopper) 1500 600 59.1 23.6side-hinged window 1200 1500 47.2 59.1top-hinged window 1200 1500 47.2 59.1vertical sliding (single, doubl

38、e, and triple hung) window 1200 1500 47.2 59.1Door Descriptions and Required Elementssingle swinging (hinged) door 1000 2125 39.4 83.7double swinging (hinged) door 1900 2125 74.8 83.7sliding door 1825 2025 71.9 79.7sidelites 600 2000 23.6 78.7transoms 2000 600 78.7 23.6Glazed Wall System Description

39、scurtain walls, storefront, and so forth. 2000 2000 78.7 78.7sloped glazing system 2000 2000 78.7 78.7Skylight Descriptionsunit skylights 1200 1200 47.2 47.2roof windows 1200 1200 47.2 47.2TABLE 1 Test Specimen SizeWindow Descriptions Width (in.) Height (in.) Width (mm) Height (mm)basement window 35

40、.4 23.6 900 600casement window 23.6 59.1 600 1500compositefixed beside operable 59.1 47.2 1500 1200compositefixed over/under operable 47.2 59.1 1200 1500dual action window (tilt/turn window) 47.2 59.1 1200 1500fixed window (picture window) 47.2 59.1 1200 1500greenhouse/garden window 35.4 35.4 11.8 9

41、00 900 300horizontal sliding window 59.1 47.2 1500 1200jalawning window 47.2 59.1 1200 1500jalousie window 35.4 47.2 900 1200pivoted window (vertical or horizontal) 47.2 59.1 1200 1500projected window (awning or hopper) 59.1 23.6 1500 600side-hinged window 47.2 59.1 1200 1500top-hinged window 47.2 5

42、9.1 1200 1500vertical sliding (single, double, and triple hung) window 47.2 59.1 1200 1500Door Descriptions and Required Elementssingle swinging (hinged) door 39.4 83.7 1000 2125double swinging (hinged) door 74.8 83.7 1900 2125sliding door 71.9 79.7 1825 2025sidelites 23.6 78.7 600 2000transoms 78.7

43、 23.6 2000 600Glazed Wall System Descriptionscurtain walls, storefront, and so forth. 78.7 78.7 2000 2000sloped glazing system 78.7 78.7 2000 2000Skylight Descriptionsunit skylights 47.2 47.2 1200 1200roof windows 47.2 47.2 1200 1200E1425 1436.4.1 For windows, doors, and skylights, the air leakage s

44、hall be recorded as pass or fail in accordance with the criteriacontained in theAAMA/WDMA/CSA 101I.S.2A440 standard. For glazed wall and sloped glazing systems, report the air leakageat both test pressures. If any adjustments need to be made, the operating force, latching force and air leakage measu

45、rements (whereapplicable) shall be repeated.NOTE 5For glazed wall and sloped glazing systems, the air leakage shall not exceed 0.3 L/s m0.06 cfm/ft2 (0.06 cfm/ft(0.3 L/s m2) at both testpressures, which is an industry standard and recommended in AAMA 501.6.5 Sound transmission loss testTransmission

46、Loss TestThe sound transmission loss shall be performed in accordance withASTM Test Method E90. If any adjustments or modifications are performed, the whole sequence of tests (operating force, latchingforce, air leakage and sound transmission loss) shall be repeated, where applicable.7. Classificati

47、on7.1 Products shall be classified based on their Outdoor-Indoor Transmission Class (OITC) and/or Sound Transmission Class(STC) ratings.7.2 The OITC rating shall be calculated in accordance with Classification E1332 for exterior window, door, skylight and glazedwall sections. The STC rating shall be

48、 calculated in accordance with Classification E413 for interior window, door and glazed wallsections. For products used for both interior and exterior applications, both the OITC and STC ratings shall be reported.8. Report8.1 Report the following information (if applicable):8.1.1 Date of test and da

49、te of report.8.1.2 Identification of the specimen (manufacturer, dimensions, type, model, materials, weight, and any other pertinentinformation). It shall be noted if test specimen does not meet the size requirements in 5.2 and Table 1.8.1.3 Detailed drawings of the specimen showing dimensioned section profiles of the