ASTM E1289-2008(2016) Standard Specification for Reference Specimen for Sound Transmission Loss《用于声音传输损失的参考试样的标准规格》.pdf

《ASTM E1289-2008(2016) Standard Specification for Reference Specimen for Sound Transmission Loss《用于声音传输损失的参考试样的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1289-2008(2016) Standard Specification for Reference Specimen for Sound Transmission Loss《用于声音传输损失的参考试样的标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1289 08 (Reapproved 2016)Standard Specification forReference Specimen for Sound Transmission Loss1This standard is issued under the fixed designation E1289; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification describes the construction and instal-lation of standard reference specimens for quality control of

3、laboratory sound transmission loss measurements using TestMethod E90.1.2 Laboratories may choose to construct and test all of thereference specimens described here or only a subset. Specificspecimens may be required by a test method or an accreditingagency.1.3 The values stated in SI units are to be

4、 regarded asstandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2C634 Terminology Relating to Building and EnvironmentalAcousticsE90 Test Method for Laboratory Measurement of AirborneSound Transmission Loss of Building Partitions andElements3.

5、Terminology3.1 DefinitionsFor definitions of terms used in thisspecification, see Terminology C634.4. Construction of Reference Specimen4.1 General:4.1.1 The reference specimen is composed of framed steelpanels. The required materials for fabrication and installationare as follows:Galvanized steel s

6、heetswidth, 1220 mm (4 ft); nominal thickness, 0.63 mm(24 gauge). The weight of the sheets shall be 5.1 0.7 kg/m2(1.05 0.15 lb/ft2).Steel right angles with 25-mm (1-in.) flangesmetal thickness, 3.2 mm (18 in.).Blind rivetsdiameter, 3.2 mm (18 in. ).Duct tape, 50 mm (2 in.) wide.Drywall screws, Type

7、Wlength, 32 mm (1.25 in.).Bolts #1024 25 mm (1 in.) long with appropriate nuts and washers.Fasteners, to hold wood frame to the perimeter of the test opening.Non-hardening, caulking,Nominal 2 by 4 in. wood framing, approximately 40 by 90 mm.NOTE 1The quantity and length of each component needed depe

8、ndson the size of the laboratory test opening.NOTE 1To simplify cleaning, the wood framing used to support thesteel panels may be painted.4.1.2 The weight of each component of the referencespecimen and the assembled specimen shall be measured andkept on record. In addition, the thickness of each of

9、the steelpanels shall be measured in six locations. (See Appendix X1.)4.2 Assembly:4.2.1 Galvanized SheetsThe length of each galvanizedsheet shall be a few millimetres less than the height of thelaboratory test opening. The total width of all the sheets shallbe a few millimetres less than the width

10、of the laboratory testopening. This may require that one or more sheets be cutlengthwise. The intent is that, when installed, the panels fill thetest opening completely.4.2.2 FrameCut steel right angles to size to form a framefor each sheet; the frame shall have the same outside dimen-sions as the s

11、heets. Notch and weld the steel angles to form thefour corners of the frame as shown in Fig. 1. Alternatively,miter the angles and weld similarly. Smooth corners afterwelding.4.2.3 PanelsConstruct a panel by riveting steel sheets tothe frames as follows:04.2.3.1 Drill holes at 100 mm (4 in.) on-cent

12、er around theperimeter of the sheets for the installation of the blind rivets. Toensure proper alignment of the sheets with the frame, it isrecommended to drill a few holes and then install rivets to holdthe sheet in place. Once this is done, the remaining holes maybe drilled and the rivets installe

13、d. Position these holes to avoidconflict with the clearance holes described in 4.2.3.2.4.2.3.2 Drill 4 mm (532 inch) diameter holes through thehorizontal members of the frame and sheet as shown in Fig. 2.These are clearance holes for the drywall screws used to attachthe panel to the wood plate (see

14、5.4). Drill similar holesthrough the vertical members of the panels that will be used toattach the assembled specimen to the vertical wood plates. Thespacing between these holes is not important.1This specification is under the jurisdiction of ASTM Committee E33 onBuilding and Environmental Acoustic

15、s and is the direct responsibility of Subcom-mittee E33.03 on Sound Transmission.Current edition approved May 1, 2016. Published May 2016. Originallyapproved in 1989. Last previous edition approved in 2008 as E1289 08. DOI:10.1520/E1289-08R16.2For referenced ASTM standards, visit the ASTM website, w

16、ww.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.2.

17、3.3 Drill 6.4 mm (14 in.) diameter holes at 406 mm (16in.) on-center through the vertical flanges of the steel frame.These are clearance holes for the bolts used to connect thepanels together (see 5.3 and Fig. 3). The holes in adjacentvertical members should be carefully aligned with each other toea

18、se installation of the panels.5. Installation A: Single Layer Reference Specimen5.1 Using approximately 40 mm by 90 mm wood studs(nominal 2 in. by 4 in.), install a wood frame around theperimeter of the laboratory opening. Use a double bead ofcaulking between the wood frame and the surface of thelab

19、oratory opening. Use suitable fasteners no more than 305mm (12 in.) on-center.5.2 Place the reference specimen against the wood framewith the flanges of the panel frames as shown in Fig. 4.NOTE 1The panels are positioned 75 mm from the mid-plane of thelaboratory test opening to minimize changes when

20、 laboratories intend totest other reference specimens described in this document that use separateplates.NOTE 2The direction of sound transmission for these referencespecimens is not important. It can be left-to-right or right-to-left.5.3 Insert 25-mm (1-in.) long No. 10-24 bolts or equivalentthroug

21、h the holes in adjacent vertical flanges drilled accordingto 4.2.3.3. Washers may be used if desired. Tighten nut snuglyto close the gap between adjacent panels. (See Fig. 3).5.4 Fasten the test panels to the vertical and horizontalsections of the wood frame with Type W drywall screws 32mm (1.25 in.

22、) long inserted through the holes drilled accordingto 4.2.3.2.5.5 Seal the test panel joints on both sides with a singlelayer of 50-mm (2-in.) wide duct tape (centered on the joints).5.6 Seal the perimeter joint on both sides with a single layerof 50-mm (2-in.) wide duct tape (centered on the joints

23、) asshown in Fig. 4.6. Installation B: Double Layer Reference SpecimenWith a Common Plate6.1 The first layer of this double layer specimen is installedas for the single layer specimen, installation A.6.2 Once the frame and the panels on one side are in place,install the second set of panels on the o

24、pposite side of the woodframe as shown in Fig. 5. Use a similar screw pattern forattaching the panels to the wood frame as on the first side.7. Installation C: Double Layer Reference Specimen withSeparate Plates-Empty Cavity7.1 The first layer of this double layer specimen is installedas for the sin

25、gle layer specimen, installation A.FIG. 1 Notching and Welding Corners of Steel AnglesFIG. 2 Construction Details of Steel Panels (not to scale)FIG. 3 Construction Details of Steel Panels (not to scale)E1289 08 (2016)27.2 Once the frame and the panels on one side are in place,install the second wood

26、 frame and the second set of panels asshown on the right side of Fig. 6. Use a similar screw patternfor attaching the panels to the second wood frame as on the firstside.7.3 The distance between the steel sheets, measured at thewood frames, shall be 150 6 3 mm.8. Installation D: Double layer referen

27、ce specimen withSeparate Plates Sound Absorbing Material in theCavity8.1 This double layer specimen is the same as installation Cwith an added layer of sound-absorbing material in the cavity.8.2 The first layer of this double layer specimen is installedas for the single layer specimen, installation

28、A.8.3 Once the frame and the panels on one side are in place,install the second wood frame as shown on the right side ofFig. 6.8.4 Install a layer of glass fibre batts in the cavity of thespecimen. The batts shall be 150 6 5 mm thick with a densityof 10 6 1 kg/m3. This density corresponds to common

29、buildinginsulation. Contact between the batts and the metal panelsshould be minimized in some convenient way.8.5 Attach the second set of panels to the second woodframe using a similar screw pattern as on the first side.9. Measurements9.1 Conduct a sound transmission loss test in accordancewith Test

30、 Method E90.9.2 The specimen area used in the calculation of transmis-sion loss shall be the area of the test opening filled by thepanels.NOTE 1Wood frame caulked, specimen joints and perimeter taped onboth sides.FIG. 4 Installation of Reference Specimen Showing Caulking ofWood Frame and the Taping

31、of the Specimen Joints and Perim-eter on Both SidesFIG. 5 Installation of Steel panels as double layer specimen on asingle wood frame. The centerline symbol, , represents the mid-plane of the test opening between two rooms.FIG. 6 Installation of Steel panels as double layer specimen on asingle wood

32、frame. The centerline symbol, , represents the mid-plane of the test opening between two rooms.E1289 08 (2016)39.3 The Test Method E90 test results for a single panelspecimen, installation A, may be compared to the values givenin Table 1, which were determined in an inter-laboratorystudy.39.4 Althou

33、gh Test Method E90 does not give results thatagree with mass law at all frequencies, test results for a singlepanel specimen may also be compared to theoretical values oftransmission loss calculated using the equation for mass law:4TL 5 20log fm 2 47.7 (1)where:TL = transmission loss, dB,f = frequen

34、cy, Hz, andm = panel mass, kg/m2.9.5 The Test Method E90 test results for a double panelspecimen, installation B, may be compared to the values givenin Table 2 which were determined in an inter-laboratory study.9.6 No interlaboratory study has yet been conducted oninstallations C and D.10. Keywords1

35、0.1 reference specimen; sound transmission loss3Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:E33-1007.4Jones, Robert E., “Intercomparisons of Laboratory Determinations of AirborneSound Transmission Loss,” Journal of the Acoust

36、ical Society of America, Vol 66,No. 1, July 1979, pp. 148164.TABLE 1 Mean and Standard Deviations of Transmission LossData on a Single Layer Specimen, Installation A.One Third OctaveBand CenterFrequency (Hz)Average LaboratoryValue of SoundTransmission Loss(dB)Standard Deviation(dB)50 12.2 1.963 12.3

37、 1.280 10.8 2.0100 11.2 1.8125 12.1 1.2160 12.9 1.3200 14.6 1.3250 15.8 1.3315 17.6 1.1400 19.1 1.2500 20.8 1.1630 22.6 1.1800 24.3 1.01000 26.0 0.91250 28.1 0.81600 29.9 0.82000 31.7 0.92500 33.6 0.83150 35.4 1.14000 37.1 1.25000 38.6 1.4STC 25.3 0.9OITC 19.0 0.7TABLE 2 Mean and Standard Deviations

38、 of Transmission LossData on a Double Layer Specimen, Installation BOne Third OctaveBand CenterFrequency (Hz)Average LaboratoryValue of SoundTransmission Loss(dB)Standard Deviation(dB)80 11.9 2.5100 10.4 2.3125 10.0 1.7160 11.6 2.0200 13.5 1.8250 15.3 2.2315 18.2 2.0400 20.9 2.1500 23.6 1.8630 27.1

39、2.0800 30.8 2.11000 34.7 2.21250 39.1 3.11600 43.5 3.02000 46.7 2.72500 50.5 2.93150 53.5 3.14000 55.0 3.75000 55.8 5.6STC 27.3 1.5OITC 19.1 1.1E1289 08 (2016)4APPENDIX(Nonmandatory Information)X1. Record FormPhysical Measurements of Steel Sheets and PanelsX1.1 Asuggested record form for physical me

40、asurements ofthe unassembled and assembled panels is shown in Fig. X1.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of

41、 any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments ar

42、e invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not rec

43、eived a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies)

44、of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ X1.1 Suggested Record FormE1289 08 (2016)5