ASTM D7613-2010 3125 Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes《柔性聚丙烯增强(fPP-R)与非增强(fPP)土工薄膜的标准规范》.pdf
《ASTM D7613-2010 3125 Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes《柔性聚丙烯增强(fPP-R)与非增强(fPP)土工薄膜的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D7613-2010 3125 Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes《柔性聚丙烯增强(fPP-R)与非增强(fPP)土工薄膜的标准规范》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D7613 10Standard Specification forFlexible Polypropylene Reinforced (fPP-R) andNonreinforced (fPP) Geomembranes1This standard is issued under the fixed designation D7613; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,
2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers flexible polypropylene rein-forced (fPP-R) and nonreinforced (fPP) geomembranes
3、 madefrom flexible polypropylene as the principal polymer preparedby the polymerization of propylene with or without other alphaolefin monomers.1.2 The tests and property limits used to characterize thesheet are values intended to ensure minimum quality. In-placesystem design criteria, such as field
4、-seaming strength andmaterial compatibility among others, are factors that should beconsidered but are beyond the scope of this specification.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport
5、 to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D573 T
6、est Method for RubberDeterioration in an AirOvenD751 Test Methods for Coated FabricsD883 Terminology Relating to PlasticsD1004 Test Method for Tear Resistance (Graves Tear) ofPlastic Film and SheetingD1204 Test Method for Linear Dimensional Changes ofNonrigid Thermoplastic Sheeting or Film at Elevat
7、edTemperatureD2136 Test Method for Coated FabricsLow-TemperatureBend TestD4439 Terminology for GeosyntheticsD4833 Test Method for Index Puncture Resistance ofGeomembranes and Related ProductsD5199 Test Method for Measuring the Nominal Thicknessof GeosyntheticsD5538 Practice for Thermoplastic Elastom
8、ersTerminology and AbbreviationsD5884 Test Method for Determining Tearing Strength ofInternally Reinforced GeomembranesD6636 Test Method for Determination of Ply AdhesionStrength of Reinforced GeomembranesD6693 Test Method for Determining Tensile Properties ofNonreinforced Polyethylene and Nonreinfo
9、rced FlexiblePolypropylene GeomembranesD7004 Test Method for Grab Tensile Properties of Rein-forced GeomembranesG151 Practice for Exposing Nonmetallic Materials in Ac-celerated Test Devices that Use Laboratory Light SourcesG154 Practice for Operating Fluorescent Light Apparatusfor UV Exposure of Non
10、metallic MaterialsG155 Practice for Operating XenonArc LightApparatus forExposure of Non-Metallic Materials3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminologies D883 and D4439 and PracticeD5538.4. Materials and Manufacture4.1 The sheet shall be cap
11、able of being heat welded, fused,or adhesively bonded to itself for making watertight fieldsplices and repairs.4.2 Geomembrane can be nonreinforced or reinforced withfabric or scrim.5. Chemical Composition5.1 The geomembrane shall be formulated from virginflexible polypropylene, in amounts greater t
12、han 85 %, byweight of the total polymer content. The remaining 15 % shall1This specification is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.10 on Geomem-branes.Current edition approved Sept. 15, 2010. Published October 2010. DOI:1
13、0.1520/D7613-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the specifications Document Summary pageon the ASTM website.1Copyright ASTM International, 100 Barr
14、Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.be comprised of compatible polymers or pigments or both,stabilizers, and colorants that are suitably compounded tosatisfy the physical requirements in the specification (seePractice D5538 for definitions).NOTE 1The compound s
15、hall not contain postconsumer (PCR) com-ponents containing bitumen or any other ingredients that could interferewith the long-term stability of the geomembrane. No more than 10 %rework resin is allowed for the production of the membrane and shall befully compatible with the parent material.6. Physic
16、al Properties6.1 Each sheet specimen shall meet or exceed the physicalrequirements prescribed in Table 1.6.2 The tolerance for time conditions (aging, weathering,and so forth) is 615 min or 61 % of the period, whichever isgreater, unless otherwise specified.6.3 The tolerance for temperature conditio
17、ns (aging and soforth) is 62C of the specified temperature, unless otherwisespecified.7. Dimensions, Mass, and Permissible Variations7.1 The width and length of the sheet shall be agreed uponbetween the purchaser and the supplier.7.2 The tolerance for both width and length shall be +3 %,-1 %.7.3 The
18、 thickness tolerance shall be +15 %, 10 % ofthickness agreed upon by the purchaser and supplier, but in nocase shall the thickness be less than the minimum in Table 1.8. Workmanship, Finish and Appearance8.1 The sheet, including factory seams, if present, shall bewatertight and free of pinholes, par
19、ticles of foreign matter,protruding fibers or reinforcement, undispersed raw material,nicks and cuts, voids, thin areas, delaminations, or othermanufacturing defects that might adversely affect serviceabil-ity.9. Test Methods9.1 DimensionsTest Methods D751, after permitting thesheet to relax at 23C
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD761320103125STANDARDSPECIFICATIONFORFLEXIBLEPOLYPROPYLENEREINFORCEDFPPRANDNONREINFORCEDFPPGEOMEMBRANES

链接地址:http://www.mydoc123.com/p-525952.html