ASTM D7174-2005(2011) 0000 Standard Specification for Preformed Closed-Cell Polyolefin Expansion Joint Fillers for Concrete Paving and Structural Construction《铺筑混凝土路面和结构建筑用预制封闭气室式聚.pdf

《ASTM D7174-2005(2011) 0000 Standard Specification for Preformed Closed-Cell Polyolefin Expansion Joint Fillers for Concrete Paving and Structural Construction《铺筑混凝土路面和结构建筑用预制封闭气室式聚.pdf》由会员分享，可在线阅读，更多相关《ASTM D7174-2005(2011) 0000 Standard Specification for Preformed Closed-Cell Polyolefin Expansion Joint Fillers for Concrete Paving and Structural Construction《铺筑混凝土路面和结构建筑用预制封闭气室式聚.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7174 05 (Reapproved 2011)Standard Specification forPreformed Closed-Cell Polyolefin Expansion Joint Fillers forConcrete Paving and Structural Construction1This standard is issued under the fixed designation D7174; the number immediately following the designation indicates the year ofor

2、iginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers preformed expansion jointfillers ma

3、de from closed-cell polyolefin materials having suit-able compressibility and nonextruding characteristics.1.1.1 Type I, closed-cell polyethylene or blended polyeth-ylene.1.2 These joint fillers are intended for use in concretepavements in full-depth joints. There are several variations insize. A ty

4、pical size measures 0.5-in. (12.7-mm) in thickness,4.0-in. (101.6-mm) in width, and 10-ft (3.048-m) in length andwill relieve stress or avoid potential distress in adjacentstructures or pavements.1.3 The values stated in inch-pound units are to be regardedas the standard.1.4 This standard does not p

5、urport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2

6、D545 Test Methods for Preformed Expansion Joint Fillersfor Concrete Construction (Nonextruding and ResilientTypes)3. Materials and Manufacture3.1 Type I, Closed-Cell Polyethylene or BlendedPolyethyleneThese fillers shall be made from foamed poly-ethylene or blended polyethylene, and their preformed

7、crosssection shall be closed-cell.4. Physical Properties4.1 Compressive Strength:4.1.1 MinimumLoad required to compress test specimenby 25 % (to 75 % of original thickness) shall not be less than5 psi (35 kPa).4.1.2 MaximumLoad required to compress test specimenby 85 % (to 15 % of original thickness

8、) shall not be greaterthan 300 psi (2070 kPa).4.2 RecoveryAfter compressing the test specimen to 50 %of its thickness before test, the load shall be released; and 10min after release of the load, the specimen shall have recoveredto at least 95 % of its thickness before test.4.3 ExtrusionWhen a 1.0-i

9、n. (25.4-mm) thick test speci-men is compressed to 50 % of its original thickness with threeof its edges restrained, the free edge shall extrude not morethan 0.5-in. (12.7-mm).4.4 Structural CharacteristicsClosed-cell expansion jointfiller units shall have sufficient strength and resiliency towithst

10、and on-the-job handling without breakage or permanentdeformation.5. Dimensions, Mass, and Permissible Variations5.1 Expansion joint filler units shall conform to dimensionsas specified:5.1.1 Thickness, +10, 0 %.5.1.2 Width, +0.8, 0 in. (+20.3, 0 mm).5.1.3 Length, +3.0, 0 in. (+76.2, 0 mm).6. Samplin

11、g6.1 Size of SamplesEach sample shall consist of sufficientmaterial to provide at least ten test specimens measuring 4.5 by4.5 in. (114.3 by 114.3 mm), or as required by the user agency.Unless otherwise specified under applicable test method, testspecimens shall be the same thickness as the expansio

12、n jointfiller units to be installed.1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.34 onPreformed Joint Fillers, Sealers and Sealing Systems.Current edition approved June 1, 2011. Published July 201

13、1. Originally pub-lished 2005. Last previous edition approved 2005 as D717405. DOI: 10.1520/D7174-05R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standard

14、s Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.2 Number of SamplesSelect one representative samplefrom each shipment of material capable of filling 5000 linear ft(1524 m) of expansion joi

15、nt filler.7. Test Methods7.1 ScopeDetermine the physical requirements prescribedin this specification under 4.2 and 4.3, in accordance with TestMethod D545.7.2 Compressive Strength (see 4.1)Determine in accor-dance with Method D545 with the following exception: Thecompressive strength shall be deter

16、mined at deflections of 25and 85 %.8. Inspection8.1 Inspection of the material and selection of sample orsamples to be tested may be made either at the point ofshipment or at the point of delivery, as agreed upon.9. Rejection and Rehearing9.1 If a selected sample fails to conform to any of therequir

17、ements of this specification, select two additionalsamples from the same lot and test. Both retest samples shallmeet the requirements of this specification or the lot will berejected.10. Precision and Bias10.1 Precision and bias statements for the tests in sections4.2 and 7.2 have not been developed

18、 at this time. Therefore,this standard should not be used for acceptance or rejection ofa material for purchasing purposes.11. Keywords11.1 cellular plastic; closed-cell; expansion joint; filler;joint; polyethylene; polyolefin; preformedASTM International takes no position respecting the validity of

19、 any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to

20、revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Y

21、our comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is co

22、pyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D7174 05 (2011)2