ASTM D6817-2007 895 Standard Specification for Rigid Cellular Polystyrene Geofoam《刚性泡沫聚苯乙烯土工泡沫材料的标准规范》.pdf

《ASTM D6817-2007 895 Standard Specification for Rigid Cellular Polystyrene Geofoam《刚性泡沫聚苯乙烯土工泡沫材料的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6817-2007 895 Standard Specification for Rigid Cellular Polystyrene Geofoam《刚性泡沫聚苯乙烯土工泡沫材料的标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6817 07Standard Specification forRigid Cellular Polystyrene Geofoam1This standard is issued under the fixed designation D 6817; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in p

2、arentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the types, physical propertiesand dimensions of rigid cellular polystyrene intended for use asgeofoam.1.2 This specific

3、ation does not cover the layout, placementand workmanship for proper installation and performance ofrigid cellular polystyrene geofoam.1.3 Rigid cellular polystyrene geofoam covered by thisspecification may need protection from certain chemicals,environmental exposure, and concentrated loads. Additi

4、onaldesign considerations may include thermal conductivity andbuoyancy. Guidelines regarding these end use considerationsare included in Appendix X1.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this s

5、tandard to establish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2C 165 Test Method for Measuring Compressive Propertiesof Thermal InsulationsC 203 Test Methods for Breaking Load and Flexu

6、ral Prop-erties of Block-Type Thermal InsulationC 303 Test Method for Dimensions and Density of Pre-formed Block and BoardType Thermal InsulationC 390 Practice for Sampling and Acceptance of ThermalInsulation LotsC 578 Specification for Rigid, Cellular PolystyreneThermalInsulationD 1621 Test Method

7、for Compressive Properties Of RigidCellular PlasticsD 1622 Test Method forApparent Density of Rigid CellularPlasticsD 2863 Test Method for Measuring the Minimum OxygenConcentration to Support Candle-Like Combustion ofPlastics (Oxygen Index)3. Terminology3.1 Definitions:3.1.1 Terms used in this speci

8、fication are defined in Termi-nology D 4439.3.1.2 geofoamblock or planar rigid cellular foam poly-meric material used in geotechnical engineering applications.3.2 Definitions of Terms Specific to This Standard:3.2.1 EPS, XXnumber designation for expanded polysty-rene geofoam Type(s) having a minimum

9、 density of XXkg/m3(lb/ft3).3.2.2 XPS, XXnumber designation for extruded polysty-rene geofoam Type(s) having a minimum density of XXkg/m3(lb/ft3).3.2.3 RCPSletter designation for EPS and XPS rigidcellular polystyrene geofoam covered by this specification.4. Ordering Information4.1 Acquisition docume

10、nts shall specify the following:4.1.1 Title, number and year of this specification.4.1.2 Type, as per Table 1, or minimum density required.4.1.3 Total product volume required of each Type, orminimum density.5. Materials and Manufacture5.1 RCPS geofoam shall be formed by the expansion ofpolystyrene r

11、esin beads or granules in a molding process (EPS)or by the expansion of polystyrene base resin in an extrusionprocess (XPS). RCPS geofoam may be manufactured withreprocessed polystyrene foam (regrind).5.2 RCPS geofoam shall be of uniform density and haveessentially closed cells. RCPS geofoam is an o

12、rganic materialand is considered combustible. It should not be exposed toflames or other ignition sources.1This specification is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.03 on Perme-ability and Filtration.Current edition approv

13、ed Dec. 1, 2007. Published December 2007. Originallyapproved in 2002. Last previous edition approved in 2006 as D 6817 06a.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, re

14、fer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Copyright by ASTM Intl (all rights reserved); Wed Sep 10 20:31:08 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to

15、 License Agreement. No further reproductions authorized.TABLE1PhysicalPropertyRequirementsofRCPSGeofoamA,BTypeEPS12EPS15EPS19EPS22EPS29EPS39EPS46XPS20XPS21XPS26XPS29XPS36XPS48Density,min.,kg/m3(lb/ft3)11.2(0.70)14.4(0.90)18.4(1.15)21.6(1.35)28.8(1.80)38.4(2.40)45.7(2.85)19.2(1.20)20.8(1.30)25.6(1.60

16、)28.8(1.80)35.2(2.20)48.0(3.00)CompressiveResistance,min.,kPa(psi)at1%15(2.2)25(3.6)40(5.8)50(7.3)75(10.9)103(15.0)128(18.6)20(2.9)35(5.1)75(10.9)105(15.2)160(23.2)280(40.6)CompressiveResistance,min.,kPa(psi)at5%35(5.1)55(8.0)90(13.1)115(16.7)170(24.7)241(35.0)300(43.5)85(12.3)110(16.0)185(26.8)235(

17、34.1)335(48.6)535(77.6)CompressiveResistance,min.,kPa(psi)at10%A40(5.8)70(10.2)110(16.0)135(19.6)200(29.0)276(40.0)345(50)104(15.0)104(15.0)173(25.0)276(40.0)414(60.0)690(100.0)FlexuralStrength,min.,kPa(psi)69(10.0)172(25.0)207(30.0)276(40.0)345(50.0)414(60.0)517(75.0)276(40.0)276(40.0)345(50.0)414(

18、60.0)517(75.0)689(100.0)Oxygenindex,min.,volume%24.024.024.024.024.024.024.024.024.024.024.024.024.0AIfyieldoccurspriorto10%deformation,reportcompressiveresistanceanddeformationatyieldinadditiontothecompressiveresistanceat1%,5%and10%deformation.BForproductsthathaveanexternalskin,testingshallbeundert

19、akenwithskinsintact.D6817072Copyright by ASTM Intl (all rights reserved); Wed Sep 10 20:31:08 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions authorized.6. Qualification Requirements6.1 The physical properties listed in Table 1 constitute themini

20、mum product qualification requirements for commonlymanufactured types of RCPS geofoam.6.2 RCPS Geofoam TypesIt is the users responsibility tospecify the required Type as inTable 1 and to obtain supportingdocumentation regarding physical properties from the materialsupplier.6.3 Combustibility Require

21、mentsAll RCPS geofoam shallcontain sufficient flame retardants to meet a minimum OxygenIndex as required in Table 1.6.4 CuringUnless otherwise specified in the contract,RCPS geofoam shall be cured for a minimum of 24 h beforedelivery and inspection.7. Availability and Dimensional Tolerance7.1 Availa

22、bilityThe RCPS geofoam materials covered bythis specification are commonly available in the size rangeshown in Table 2. Specific RCPS geofoam block dimensionsvary by manufacturer equipment characteristics.7.2 Dimensional ToleranceUnless otherwise specified,the acceptable length, width, thickness, fl

23、atness and squarenesstolerance criteria on RCPS geofoam shall not exceed 6 0.5 %.8. Damage and Degradation8.1 DamageRCPS geofoam as delivered to the projectsite shall have no defects that will adversely affect its serviceand workability qualities. Material units that manifest unac-ceptable surface o

24、r volumetric damage shall be replaced.8.1.1 Surface DamageDamage to load bearing RCPSgeofoam surfaces shall be limited to less than 20 % of theequivalent load bearing area of the unit.8.1.2 Volume DamageVolumetric damage of RCPS geo-foam shall be limited to less than 1 % of the volume of a singleuni

25、t.8.1.3 UV (Ultra-Violet) DegradationDiscoloration anddusting of RCPS geofoam caused by the extensive exposure tosunlight is a defect that will adversely affect its service and isgrounds for rejection. Refer to X1.6.9. Inspection9.1 SamplingUnless otherwise specified in the purchaseorder or contract

26、, the material shall be sampled for inspectionin accordance with Criteria C 390.9.2 WeightDetermine the weight of selected full size unitsin accordance with Test Method D 1622, or as specified.9.3 DimensionsVerify specified dimensions and toler-ances, as prescribed in Test Method D 1622 and 7.2 of t

27、hisspecification.9.4 DensityCompute the density of test samples in accor-dance with Test Method D 1622.10. Acceptance or Rejection10.1 Material that fails to conform to this specification shallbe rejected promptly in writing. The manufacturer or suppliershall have the right to re-inspect the rejecte

28、d shipment andresubmit selected units for acceptance under tightened inspec-tion.11. Certification11.1 Unless otherwise specified in the purchase order orcontract, the manufacturer or supplier shall furnish third partycertification that representative material has either been testedor inspected as d

29、irected in the specification and the require-ments have been met. When specified in the purchase order orcontract, a report of the test results shall be furnished.12. Product Marking12.1 The following shall be marked on each whole unit ofproduct:12.1.1 Manufacturers Identification,12.1.2 Date of Man

30、ufacture,12.1.3 Type, (See Table 1), and12.1.4 Weight, or Density.13. Test Methods13.1 Dimensions and DensityTest in accordance with TestMethod C 303 or Test Method D 1622.13.2 Compressive ResistanceTest in accordance with TestMethod C 165 or Test Method D 1621 using 50 mm (2 in.)cubes. The rate of

31、cross-head movement shall be 5.0 6 0.5mm/min (0.2 6 0.02 in/min) equivalent to 10 % strain perminute.13.3 Flexural StrengthTest in accordance with TestMethod C 203.13.4 Oxygen IndexTest in accordance with Test MethodD 2863.14. Keywords14.1 block; board; cellular polystyrene; EPS; expandedpolystyrene

32、; extruded polystyrene; foam plastic; geofoam;RCPS; reprocessed; rigid cellular polystyrene; XPSTABLE 2 Common Manufactured Dimensions of RCPS GeofoamDimension, mm (in.) All EPS Types All XPS TypesWidth 305 to 1219 (12 to 48) 406 to 1219 (16 to 48)Length 1219 to 4877 (48 to 192) 1219 to 2743 (48 to

33、108)Thickness 25 to 1219 (1 to 48) 25 to 102 (1 to 4)D6817073Copyright by ASTM Intl (all rights reserved); Wed Sep 10 20:31:08 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions authorized.APPENDIX(Nonmandatory Information)X1. END-USE CONSIDERATIONS

34、X1.1 Thermal ResistanceX1.1.1 RCPS geofoam also functions as a thermal insula-tion.The thermal insulation properties of RCPS geofoam are asspecified in Specification C 578, and may impact the end usedesign of applications subject to different exposure conditions.Consult the RCPS geofoam manufacturer

35、 for specific recom-mendations.X1.2 Solvent ExposureX1.2.1 RCPS geofoam must be protected from petroleumbased solvents and their vapors. Examples of these solventsare: gasoline, diesel fuel, concrete curing compound, coal tarpitch, and asphaltic mastic compounds.X1.3 Equipment TrafficX1.3.1 Equipmen

36、t traffic that can impose contact pressuresin excess of the allowable design stress for RCPS geofoamshould be restricted. Protective materials such as sheathing orplanks may be placed on the material to allow light rubber-tiredequipment use.X1.4 BuoyancyX1.4.1 RCPS geofoam becomes buoyant when subme

37、rgedin water and adequate ballast must be provided to resistexpected uplift forces.X1.5 DesignX1.5.1 The design and installation of RCPS geofoam is theresponsibility of the user.X1.5.2 RCPS geofoam can be supplied precut to specifieddimensions to fit specific project needs. Desired shapes andsizes c

38、an also be field cut with a hot wire, saw, or other cuttingtool.X1.6 Ultra-Violet DegradationX1.6.1 Discoloration and dusting of load bearing surfacesof RCPS geofoam caused by extended exposure to sunlightshall be removed by pressure washing.ASTM International takes no position respecting the validi

39、ty of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subjec

40、t to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarte

41、rs. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard

42、is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D6817074Copyright by ASTM Intl (all rights reserved); Wed Sep 10 20:31:08 EDT 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproductions authorized.