ASTM D6085-1997(2006) Standard Practice for Sampling in Rubber Testing-Terminology and Basic Concepts《橡胶测试中取样的标准实施规程 术语和基本概念》.pdf

《ASTM D6085-1997(2006) Standard Practice for Sampling in Rubber Testing-Terminology and Basic Concepts《橡胶测试中取样的标准实施规程 术语和基本概念》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6085-1997(2006) Standard Practice for Sampling in Rubber Testing-Terminology and Basic Concepts《橡胶测试中取样的标准实施规程 术语和基本概念》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 6085 97 (Reapproved 2006)Standard Practice forSampling in Rubber TestingTerminology and BasicConcepts1This standard is issued under the fixed designation D 6085; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the ye

2、ar of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers a standardized terminology andsome basic concepts for testing and sampling across the broa

3、drange of chemical and physical testing operations characteristicof the rubber and carbon black manufacturing industries.1.2 In addition to the basic concepts and terminology, amodel for the test measurement process is given in Annex A1.This serves as a mathematical foundation for the terms andother

4、 testing concepts. It may also find use for further devel-opment of this practice to address more complex samplingoperations.1.3 This general topic requires a comprehensive treatmentwith a sequential or hierarchical development of terms withsubstantial background discussion.Anumber of ancillary term

5、sare also given that make for a more self-contained document.This cannot be accommodated in Terminology D 1566.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safe

6、ty and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1566 Terminology Relating to RubberD 4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustriesD 54

7、06 Practice for RubberCalculation of ProducersProcess Performance Indexes3. Terminology3.1 Definitions:3.2 Despite the adoption of standard test methods, test resultvariation influences the data generated in all testing programs.As outlined in Annex A1, there are two main categories: (1)variation in

8、herent in the production process for a material orclass of objects, and (2) variation due to the measurementoperation itself. Each of these two sources may be furtherdivided into two types of variation: (1) systematic or biasvariation, and (2) random error variation. Both types can existsimultaneous

9、ly for either of the main categories.3.3 Random variation can be reduced to a low level byappropriate replication and sampling procedures, but biasvariation cannot be so reduced. However, bias variation can bereduced or eliminated by comprehensive programs to sort outthe causes of such perturbations

10、 and eliminate these causes.3.4 Elementary Testing Terms:3.4.1 lot, na specified mass of material or number ofobjects, generated by an identifiable process, with a recognizedcomposition or property range.3.4.1.1 DiscussionA lot is frequently generated by acommon production process in a restricted ti

11、me period andusually consists of a finite size or number. A lot may be afractional part of a population (Interpretation 2 of population).3.4.2 material, na specific entity that exists in bulk form(solid, powder, liquid).3.4.2.1 DiscussionA material may or may not be homo-geneous. Typical materials a

12、re individual rubbers, compounds,accelerators, carbon blacks, etc.3.4.3 object, na discrete item or piece with a specifiedshape and size.3.4.3.1 DiscussionUsually an object is an entity that isready for testing.Atypical object is an o-ring, dumbbell, pellet,or hose assembly.3.4.4 object class (or cl

13、ass of objects), na number ofobjects, with a recognized property range, generated by acommon process, the objects are usually characterized by thevalue(s) of a unique property.3.4.4.1 DiscussionIn any testing program the phrase “arecognized property range” implies that the tester is aware ofthe appr

14、oximate value of this range. At one extreme, thisrecognized range may denote “essentially identical propertyvalues;” at the opposite extreme this recognized range maydenote “widely varying property values.” The range applies to1This practice is under the jurisdiction of Committee D11 on Rubber and i

15、s thedirect responsibility of Subcommittee D11.16 onApplication of Statistical Methods.Current edition approved Oct. 1, 2006. Published November 2006. Originallyapproved in 1997. Last previous edition approved in 2002 as D 6085 97 (2002).2For referenced ASTM standards, visit the ASTM website, www.as

16、tm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.both mat

17、erials and object classes, and testing programs willdiffer in regard to the extent of variation under consideration.3.4.5 population, na generic term used in testing opera-tions that may refer to any one of the following: (1) a singleobject or a very limited mass of material, (2) a finite (but large

18、)number of objects or large mass of material, or (3) a hypo-thetical infinite number of objects or mass of material; all threeinterpretations imply that the objects or material are generatedby some identifiable process and have recognized propertyrange.3.4.5.1 DiscussionTesting programs may vary fro

19、m avery limited focus of attention (Interpretation 1) to an extremeor broad focus of attention (Interpretation 3). The focus ofattention is determined by the testing and the samplingprogram.3.4.6 test (or testing), na technical procedure performedon a material or object class using specified equipme

20、nt thatproduces data unique to the material or object class; the dataare used to evaluate or model selected properties or character-istics.3.4.6.1 DiscussionTesting can be conducted on a narrowor broad basis, depending on the decisions to be made for anyprogram. Sampling and replication plans (see 3

21、.5) need to bespecified for a complete program description. Testing may bedivided into two major categories:3.4.6.2 global testing, ntesting that is conducted at two ormore locations or laboratories for the purpose of comparingmaterials or object classes at each location for selectedcharacteristic p

22、roperties.3.4.6.3 DiscussionTypical global testing applications areproducer-user testing and interlaboratory comparisons such asprecision evaluation. These may be conducted on a worldwidebasis.3.4.6.4 local testing, ntesting that is conducted at onelocation or laboratory for the purpose of comparing

23、 a numberof materials or object classes for some selected characteristicproperties.3.4.6.5 DiscussionQuality control and internal develop-ment programs are typical local testing.3.5 Sampling and Related Testing Terms:3.5.1 random sample, none of a sequence of samples (orsub-samples) taken on a rando

24、m basis from a lot or population.3.5.2 replicate, na generic term used in testing operationsthat denotes one of a selected number of fractional parts orobjects taken from a sample; each fractional part or object istested.3.5.3 replication, nthe act of selecting replicates.3.5.3.1 DiscussionThe prima

25、ry purpose of replication isthe reduction of random test measurement variation. SeeAnnex A1 for additional discussion on types of replication.3.5.4 sample, na small fractional part of a material or aspecified number of objects that are selected from a lot fortesting, inspection, or specific observat

26、ions of particular char-acteristics.3.5.4.1 DiscussionA sample may be obtained from thecombination of a series of incremental parts, each part obtainedin one step of a particular sampling process (see sub-sample).3.5.5 sampling, nthe act of selecting samples of any type.3.5.5.1 DiscussionThe goals o

27、f sampling are (1) an accu-rate or representative evaluation of the characteristic propertiesof the lot or population, and (2) an accurate estimate of thevariation of properties within the lot or population.3.5.6 sub-sample, none of a sequence of intermediatefractional parts or intermediate sets of

28、objects taken from a lotor population that usually will be combined in a prescribedprotocol to form a sample.3.5.7 systematic sample, none of a sequence of samples(or sub-samples), each taken from a particular location orregion of a lot or population according to a prescribed plan; theusual goal is

29、to determine if the lot or population is homoge-neous.3.5.7.1 DiscussionNon-homogeneity may be of a randomnature or it may be systematic (variation), which is frequentlyreferred to as “stratification.”3.5.8 test piece, nsee test specimen, the preferred term.3.5.9 test portion, nsee test sample, the

30、preferred term.3.5.10 test sample, nthat part of a sample of any typetaken (usually with a prescribed blending or other protocol) forchemical or other analytical testing.3.5.10.1 DiscussionA test sample may be a replicate or itmay be subdivided into n replicates; these n replicates arefrequently cal

31、led “laboratory samples.” Test samples are typi-cally drawn to represent materials such as rubbers, pigments,chemicals, etc.3.5.11 test specimen, nan object (appropriately shapedand prepared) taken from a sample for physical or mechanicaltesting.3.5.11.1 DiscussionA test specimen is usually a replic

32、ate.Test specimens are typically prepared by a rubber processing(and curing) operation to evaluate characteristic properties ofdevelopment compounds and the compounds used in manufac-tured rubber products. They may also be manufactured rubberparts such as o-rings, motor mounts, etc.3.6 Testing Varia

33、tion TermsAnnex A1 defines a numberof test data variation terms (see A1.4). Some additional terms,as given below, apply to typical development testing as well asquality control and quality assurance.3.6.1 common cause variation, nthat residual variationinherent in any process that (1) is operating i

34、n a state ofstatistical control, and (2) is operating at some recognized orascertained level of technological competence (PracticeD 5406).3.6.2 special cause variation, nthat variation attributableto certain specific or assignable sources that have been (or maybe) discovered through an investigation

35、 of the process (PracticeD 5406).3.6.2.1 DiscussionBoth common and special cause varia-tion may contain bias as well as random variation components.A synonym for common cause variation is non-assignablevariation; a synonym for special cause variation is assignablevariation.3.6.3 total process variat

36、ion, na range, along the mea-sured property scale, defined as six times the standard devia-tion (determined under specified process conditions); thevariation may contain either common or combined commonand special cause sources (Practice D 5406).D 6085 97 (2006)23.6.3.1 DiscussionAlthough this is de

37、fined in terms ofquality control operations, it applies equally to general testing.For this general testing, the “process” and the “standarddeviation” refer to the total (testing and sampling) operation.4. Significance and Use4.1 This practice provides a standardized terminology and areview of some

38、basic concepts for elementary sampling andtesting. These operations are important for: (1) local orintralaboratory testing that generally applies to internal qualitycontrol, process capability or performance evaluation, as wellas development programs, and (2) global or interlaboratorytesting that ap

39、plies to producer-user and other testing programsthat have industry-wide or worldwide scope. It is recognizedthat certain test methods may require more detailed andspecialized sampling operations than the generic ones asdescribed herein. These specialized sampling proceduresshould utilize, as far as

40、 possible, the basic concepts as given inthis practice.4.2 This practice provides a list of terms and concepts thatmay be used in numerous test methods used by CommitteesD11 and D24. It improves communication among those thatconduct testing in the rubber and carbon black manufacturingindustries and

41、those that use such testing and test results fortechnical decisions.5. Elementary Sampling Concepts5.1 The purpose of testing is the production of test data to beused to make technical decisions. Test data are the end result ofa three-step process: (1) test program organization, (2) sam-pling, and (

42、3) testing. Test data quality depend on the organi-zation and the sampling for any program.5.2 Types of Sampling Plans:5.2.1 Intuitive SamplingThis is a plan organized on thebasis of the developed skill and judgment of the sampler.General information of the lot or population as well as pastsampling

43、and testing experience are used to make samplingdecisions. The decisions made on the data generated by such aplan are based on a combination of the skill and experience ofthe tester buttressed by limited statistical conclusions. Strictprobabilistic conclusions usually are not warranted.5.2.2 Statist

44、ical SamplingThis is based on strict statisticalsampling and such a plan provides the basis for authenticprobabilistic conclusions. Hypothesis testing may be con-ducted, inferences drawn, and predictions made about futuresystem or process behavior. Usually a large number of samplesare needed if the

45、significance of small differences is ofimportance. Conclusions from this type of sampling usually arenot controversial. The statistical model chosen is important.When the number of samples required is large and this imposesa testing burden, hybrid plans using some simplifying intuitiveassumptions ar

46、e frequently employed.5.2.3 Protocol SamplingThese are specified plans usedfor decision purposes in a given situation. Regulations (of theprotocol) usually specify the type, size, frequency, and periodof sampling in addition to the test methods to be used and otherimportant sampling issues. The prot

47、ocol may be based on acombination of intuitive and statistical considerations. Testingfor conformance with producer-user specifications for com-mercial transactions is typical for this approach.5.3 Ensuring the Quality of Samples and Testing:5.3.1 Only the most elementary sampling issues are ad-dres

48、sed in this section. For more detailed information, standardtexts on sampling and sampling theory should be consulted.Well defined sampling operations must be conducted to ensurethat high quality samples are used for any testing program.Quality is ensured when the samples are drawn in accordancewith

49、 a prescribed procedure. This ensures that they accuratelyrepresent the lot or population. Such issues as sample homo-geneity (or unintended stratification) and sample stability(conditioning or storage changes in the sample prior to testing)must be addressed. The sampling procedures, holding time,and other handling operations should be well documented. Thetest methods used for any program should be stable or in a stateof statistical control and have demonstrated sensitivity as wellas good precision in regard to the measured parameter.5.3.2