ASTM D5749-2001(2006) Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing《密封和保险用增强和普通纸胶带的标准规范》.pdf
《ASTM D5749-2001(2006) Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing《密封和保险用增强和普通纸胶带的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D5749-2001(2006) Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing《密封和保险用增强和普通纸胶带的标准规范》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 5749 01 (Reapproved 2006)Standard Specification forReinforced and Plain Gummed Tape for Sealing andSecuring1This standard is issued under the fixed designation D 5749; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,
2、the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers plain and reinforced papergummed adhesive tapes suitable for securing and bandi
3、ngpaper products and closing fiberboard boxes.1.2 This specification is intended to replace Fed. Specs. CIDA-A-1492, CID A-A-1671, and PPP-T-45 in part.1.3 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.4 The following safety ha
4、zards caveat pertains only to thetest methods portion, Section 11, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and
5、determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 685 Practice for Conditioning Paper and Paper Productsfor TestingD 828 Test Method for Tensile Properties of Paper andPaperboard Using Constant-Rate-of-Elongation ApparatusD 996 Terminolo
6、gy of Packaging and Distribution Environ-mentsD 1974 Practice for Methods of Closing, Sealing, andReinforcing Fiberboard BoxesD 3951 Practice for Commercial Packaging2.2 TAPPI Standards:T 401 Fiber Analysis of Paper and Paperboard3T 410 Weight per Unit Area (Basis Weight or Substance)3T 414 Internal
7、 Tearing Resistance of Paper (Elmendorf-Type Method)3UM 575 Water Resistance of Adhesive Bond in LaminatedPaper and Paperboard32.3 ANSI/ASQC Standards:ANSI/ASQC Z 1.4 Sampling Procedures and Tables forInspection by Attributes4ANSI/ASQC Z 1.9 Sampling Procedures and Tables forInspection by Variables
8、for Percent Defective42.4 Federal Specifications:PPP-T-45 Tape, Gummed, Paper, Reinforced and Plain, forSealing and Securing5PPP-T-681 Tape, Gummed, Packaging and Packing of5CID A-A-1492 Commercial Item Description Tape,Gummed, Paper, Plain5CID A-A-1671 Commercial Item Description Tape,Gummed, (Pape
9、r, Reinforced, Laminated)52.5 ISO Standard:ISO 9002 Quality Systems Model for Quality Assurance inProduction and Installations43. Terminology3.1 DefinitionsGeneral definitions for packaging and dis-tribution environments are found in Terminology D 996.4. Classification4.1 Type I Reinforced, Laminate
10、d:4.1.1 Class 1Strippable.4.1.2 Class 2Nonstrippable.4.2 Type II Plain, Single Ply, Strippable:4.2.1 Grade ALight duty, for lightweight packages.4.2.2 Grade BMedium duty, for medium-sized packages.4.2.3 Grade CHeavy duty, for heavy-duty packages.1This specification is under the jurisdiction of ASTM
11、Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved April 1, 2006. Published April 2006. Originallyapproved in 1995. Last previous edition approved in 2001 as D 5749 01.2For referenced ASTM standards, visit the ASTM website, ww
12、w.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Technical Association of the Pulp and Paper Industry (TAPPI),P.O. Box 105113,Atlanta, GA30348; 15 Techn
13、ology Parkway South, Norcross, GA30092.4Available from American National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.5Available from Superintendent of Documents, U.S Government Printing Office,Washington, DC 20402.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C70
14、0, West Conshohocken, PA 19428-2959, United States.5. Significance and Use5.1 Type I is a reinforced gummed tape which may bestrippable (Class 1) or nonstrippable (Class 2). It is intendedfor use in Methods 2C2, 2C3, and any other methods inPractice D 1974.5.2 Type II is a plain paper-backed nonstri
15、ppable gummedtape. It is intended for use in Methods 2C4, 2C5, and othermethods in Practice D 1974.6. Ordering Information6.1 The inquiry or order shall include the following:6.1.1 ASTM designation and date of issue,6.1.2 Type, class, and grade required (5.1),6.1.3 When core plugs are required (7.7)
16、,6.1.4 If tape is to be wound gummed side out (7.7),6.1.5 Roll width and length (9.1 and 9.2),6.1.6 Acceptance sampling plan and desired acceptancequality level (Section 12),6.1.7 When backing certification is required (15.1),6.1.8 When testing and inspection certification is required(15.1),6.1.9 Le
17、vel of packaging and packing if other than commer-cial (Section 17), and6.1.10 When packaging for shipments to the U.S. Govern-ment (17.2).7. Materials and Manufacture7.1 The materials used in the construction of the tape shallbe such as to ensure performance of the tape over the range of55 to +71C
18、( 65 to +160F) and shall conform to therequirements of this specification.7.2 Paper:7.2.1 StockThe paper used in the fabrication of the tapeshall be a kraft paper. The use of recycled pulp in the paper isencouraged.7.2.2 WeightThe weight of the paper prior to gummingshall conform to the requirement
19、of Table 1, when tested asdescribed in TAPPI T 410.7.3 AdhesivesThe adhesives used shall not have an offen-sive odor (dry or wet) and shall meet the environmentalconsiderations of 16.1.7.3.1 Type I, Class 1 adhesive shall be capable of beingquickly activated with water. The wetted adhesive shall sho
20、wpronounced tackiness and shall cause the tape to remain sofirmly affixed that it cannot be removed without leaving a thinfilm of paper from the tape on the test paper, when tested inaccordance with 13.6.1.7.3.2 Type I, Class 2, and Type II adhesive shall be capableof being quickly activated with wa
21、ter. The wetted adhesiveshall show pronounced tackiness and shall cause the tape toremain so firmly affixed that it cannot be removed withoutfailure of either the tape or paper when tested in accordancewith 13.6.1.7.4 Reinforcing MaterialsThe reinforcing fibers used infabricating Type I tapes shall
22、be composed of glass of such sizeas to permit the reinforced tape to meet the requirements setforth in Table 2 when tested as described in 13.5.7.5 Laminating MaterialsThe laminating material forType I tape shall be non-asphaltic, water resistant, flexible, andnon-staining. Water resistance of the f
23、inished tape shall betested in accordance with TAPPI UM 575.7.6 ConstructionType I tape shall consist of two strips ofpaper in roll form, securely laminated together with reinforcingfibers embedded in the laminate. The reinforcing laminatedtape shall be completely and uniformly coated on one side wi
24、than adhesive.7.6.1 The tape shall be reinforced by crosswise reinforcingfibers spaced not less than 2 fibers/50 mm (1 in.) on averageand by lengthwise fibers spaced not more than an average of 25mm (12 in.) apart. If a diamond pattern is employed forcrosswise reinforcement, the spacing between the
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD574920012006STANDARDSPECIFICATIONFORREINFORCEDANDPLAINGUMMEDTAPEFORSEALINGANDSECURING 密封 保险 增强 普通
链接地址:http://www.mydoc123.com/p-520573.html