ASTM D5094 D5094M-2009 Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures《带螺纹或焊片式密封盖容器的液体总泄漏量标准试验方法》.pdf

《ASTM D5094 D5094M-2009 Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures《带螺纹或焊片式密封盖容器的液体总泄漏量标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5094 D5094M-2009 Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures《带螺纹或焊片式密封盖容器的液体总泄漏量标准试验方法》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 5094/D 5094M 09Standard Test Methods forGross Leakage of Liquids from Containers with Threaded orLug-Style Closures1This standard is issued under the fixed designation D 5094/D 5094M; the number immediately following the designation indicates theyear of original adoption or, in the ca

2、se of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods may demonstrate container/closureintegrity with threaded or lug-style c

3、losures by the determina-tion of gross leaks in rigid and semi-rigid containers (up to 4 L1.06 g. Such tests may be used to indicate the ability of aliquid container to survive the distribution environment with-out leaking. These test methods may not be suitable todetermine the leak resistance of co

4、ntainers intended for trans-port of hazardous materials.1.2 Test Methods:1.2.1 Test Method A, Shipping Container Vibration andStorage Test, covers the ability of a shipping container and itsinterior packaging to protect the contents from leakage aftertransportation induced vibration and high-tempera

5、ture storage.1.2.2 Test Method B, Shipping Container Vibration andVacuum Chamber Test, is suitable for individual containers andis usually less severe than Test Method A. The advantage ofTest Method B is the shortness of the test.1.3 The values stated in either SI units or inch-pound unitsare to be

6、regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address the safetyc

7、onserns associated with its use. It is the responsibility of theuser of this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 996 Terminology of Packaging and Distribution

8、 Environ-mentsD 999 Test Methods for Vibration Testing of ShippingContainersD 3198 Test Method for Application and Removal Torqueof Threaded or Lug-Style ClosuresD 3474 Practice for Calibration and Use of Torque MetersUsed in Packaging ApplicationsD 4169 Practice for Performance Testing of Shipping

9、Con-tainers and SystemsD 4332 Practice for Conditioning Containers, Packages, orPackaging Components for TestingD 7386 Practice for Performance Testing of Packages forSingle Parcel Delivery Systems3. Terminology3.1 General definitions for packaging are found in Termi-nology D 996.3.2 Definitions of

10、Terms Specific to This Standard:3.2.1 gross leakany opening in the container or closureseal that produces visible leakage such that the container wouldnot be suitable for transport or subsequent distribution.3.2.2 leakany opening in a container which, contrary tointention, either lets contents escap

11、e or permits substances toenter.3.2.3 leakagethat which passes through a leak.4. Summary of Test Methods4.1 Method A, Shipping Container Vibration and StorageTestTest specimens are filled to their expected fill capacitywith product or liquid simulating product and the closure isapplied to the contai

12、ner. Closures should be applied with thesame torque as would be encountered in production. Thespecimens are packed into shipping containers and vibrated.The specimens, stored on their sides, are subjected to 40C104F (or other conditions as appropriate) for four weeks.Each specimen is examined for le

13、akage.4.2 Method B, Container Vibration and Vacuum ChamberTestTest specimens are partially filled with product or liquidsimulating product and the closure is applied to the container.Closures should be applied with the same torque as would beencountered in production. The specimens are packed into1T

14、his test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.32 on Consumer,Pharmaceutical and Medical Packaging.Current edition approved Oct. 1, 2009. Published October 2009. Originallyapproved in 1990. Last previous edition approv

15、ed in 2004 as D 5094 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Ba

16、rr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.shipping containers and vibrated. Following vibration, theindividual specimens are removed from the shipping containerand subjected to 34 kPa 10 in. Hg vacuum for 10 min andexamined for leakage.NOTE 1Other levels of vacuum

17、, or time, or both may be appropriate.5. Significance and Use5.1 These test methods are used to indicate the integrity ofthe container and closure system in the distribution environ-ment.5.2 These test methods measure the ability of the containerand closure system to prevent leakage when stored or t

18、rans-ported upright, inverted, or on the side.5.3 These test methods allow for comparison of container/closure designs of threaded and lug-style closures of similar ordifferent materials, or different manufacturers. These tests aresuitable for packaging development, engineering and toolingevaluation

19、s.6. Apparatus6.1 Method A, Shipping Container Vibration and StorageTest:6.1.1 Drying Oven, constant-temperature, equipped withmeans for ensuring adequate temperature control, 40 6 1C104 6 1.8F and air circulation, ambient humidity, or otherconditions as appropriate.6.1.2 Torque Meter, with an appro

20、priate scale which accu-rately measures within the expected torque range.6.1.3 Vibration Test Machine, the apparatus described in theApparatus section of Test Methods D 999 may be used.6.2 Method B, Shipping Container Vibration and VacuumTest:6.2.1 Vacuum Chamber, any suitable chamber capable ofwith

21、standing approximately one atmosphere pressure differen-tial, fitted with a vacuum-tight seal. A vacuum gauge, an inlettube from a source of vacuum, and an outlet tube to theatmosphere shall be sealed to the chamber. The inlet and outlettubes shall be equipped with shut-off valves. The vacuumgauge s

22、hall be laboratory quality with a full scale range of 0 to100 kPa 0 to 30 in. Hg.6.2.2 Torque Meter, with an appropriate scale which accu-rately measures within the expected torque range.6.2.3 Vibration Test Machine, the apparatus described in theApparatus section of Test Methods D 999 may be used.7

23、. Sampling7.1 The complete test unit shall consist of the shippingcontainer, with interior packaging and the actual test specimens(container(s) and closure(s).7.2 A minimum of three specimens representing each vari-able, such as cap or bottle mold from each cavity but not lessthan ten specimens are

24、to be selected. The total number ofspecimens may need to be increased to completely fill theshipping container. More than one shipping container may berequired.7.3 Select unused closures and unused containers that arewithin specifications.8. Test Specimens8.1 Test Method AAspecimen shall be one cont

25、ainer filledto expected fill capacity with product or liquid simulatingproduct. The closure is secured in accordance with 11.1.8.2 Test Method BA specimen shall be one containerone-third filled with product or liquid simulating product. Theclosure is secured in accordance with 11.1.8.3 Colorant shou

26、ld be added to the contents when neces-sary to give permanent indication where there is leakage.9. Calibration9.1 Calibrate the torque meter in accordance with PracticeD 3474.10. Conditioning10.1 Store the shipping container components at ambientlaboratory conditions for at least 4 h before testing,

27、 or otherconditions in accordance with Practice D 4332.10.2 Store the torqued container/closure test specimensupright at least 24 h at ambient conditions before commencingthe test.11. Procedure11.1 Apply closures to the containers according to theApplication Torque Measurement section of the procedu

28、re inTest Method D 3198.11.2 Test Method A, Shipping Container Vibration andStorage Test:11.2.1 Place the filled specimens in their shipping containeror in an appropriate carton so that they will remain firmly inplace during vibration.11.2.2 Proceed as directed according to Test Methods D 999(Method

29、 A 1 or A 2) 20 min each on bottom, top, and one side,or run an entire shipping cycle in accordance with PracticeD 4169 (for multiple parcel shipments) or with Practice D 7386(for single parcel shipments).11.2.3 Remove the specimens from the shipping containeror carton. Examine all specimens for vis

30、ible leakage withoutremoving or disturbing the closure. Note the location(s) ofleakage.11.2.4 Place the test specimens on their sides (liquid incontact with finish/closure) in a container capable of holdingthe liquid should a leak develop. It is recommended thatabsorbent blotting paper be placed ben

31、eath the samples to moreeasily detect leakage. Store the test specimens at 40 6 1C104 6 1.8F, or other appropriate temperature, ambienthumidity (see the Preferred Atmospheres listing in PracticeD 4332) and inspect for liquid leakage at 24 h and at one-weekintervals for four weeks. Note location(s) o

32、f leakage.11.2.5 At the conclusion of the test, remove the closure andinspect the threads for signs of leakage or crusting from partialleakage.11.3 Test Method B, Shipping Container Vibration andVacuum Chamber Test:11.3.1 Place the partially filled specimens in their shippingcontainer or in an appro

33、priate carton so that they will remainfirmly in place during vibration.11.3.2 Proceed as directed according to Test Methods D 999(Method A 1 or A 2) 20 min each on bottom, top, and one side,D 5094/D 5094M 092or run an entire shipping cycle in accordance with PracticeD 4169 (for multiple parcel shipm

34、ents) or with Practice D 7386(for single parcel shipments) as desired.11.3.3 Remove the specimens from the shipping containersor carton. Examine all specimens for visible leakage withoutremoving or disturbing the closure. Note location(s) of leakage.11.3.4 Place the partially filled specimens invert

35、ed in abeaker or other receptable to contain leakage.NOTE 2Other orientations of the specimens may be appropriate.Orientation of the container should be such that suspected leak areas arecovered with the liquid inside the container.11.3.5 Place specimens in the vacuum chamber and closethe vacuum cha

36、mber.11.3.6 Close the chamber inlet valve.11.3.7 Open the chamber outlet valve and turn on vacuumsource so that the gauge rises slowly (from 30 s to 1 min) to34 kPa 10 in. Hg and close the outlet valve.11.3.8 Maintain the vacuum for 10 min.11.3.9 Partially open the chamber inlet valve and release th

37、evacuum slowly (30 s to 1 min).11.3.10 Open the chamber.11.3.11 Remove the specimens and examine for leakage,cracks, or other visible damage. Record the results of thisexamination. Note location(s) of leakage.12. Interpretation of Results12.1 If there is leakage to the outside of the specimen, thepa

38、ckage fails the test.12.2 If there is no leakage to the outside of the specimen thepackage passes the test.12.3 If there is leakage to the threads but not to the outside,the specimen may or may not be acceptable. This effect may beused as a comparative evaluation between closures and moldcavities.13

39、. Report13.1 Report the following information:13.1.1 Statement that testing was done in accordance withASTM Test Method D 5094, Test Method A or Test Method B,or that the testing was done with indicated changes.13.1.2 Description of shipping cycle(s) used: per PracticeD 4169 or Practice D 7386, or b

40、oth.13.1.3 Materials of construction of the closure, liner andcontainer including finish and manufacturers designation.13.1.4 Description of the shipping container and interiorpackaging, the test frequencies, intensities, and durations used.13.1.5 Product or substitute used and fill level.13.1.6 Sta

41、tement whether or not leakage occurred and, ifpossible, a report of the location of each leak.13.1.7 Statement of the number of specimens included inthe test and the number of failures, if any.13.1.8 Conditioning time, temperature, and relative humid-ity.13.1.9 Temperature and relative humidity of t

42、he test area.13.1.10 Time between application and removal of closures.13.1.11 Compilation of measured torques.13.1.12 If Test Method B is used, a statement of vacuum andduration.13.1.13 Statement of observations that may lead to im-provements.14. Precision and Bias14.1 No statement is made about eit

43、her the precision or biasof this test method since the result merely states whether thereis conformance to the criteria for success specified in theprocedure.15. Keywords15.1 closure leakage; container leakage; leak; leakage; liq-uid leakage; vacuumASTM International takes no position respecting the

44、 validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

45、 subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Hea

46、dquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This st

47、andard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 5094/D 5094M 093