ASTM D4814-2016 Standard Specification for Automotive Spark-Ignition Engine Fuel.pdf

《ASTM D4814-2016 Standard Specification for Automotive Spark-Ignition Engine Fuel.pdf》由会员分享，可在线阅读，更多相关《ASTM D4814-2016 Standard Specification for Automotive Spark-Ignition Engine Fuel.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4814 15aD4814 16Standard Specification forAutomotive Spark-Ignition Engine Fuel1This standard is issued under the fixed designation D4814; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A n

2、umber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers the establishment of re

3、quirements of liquid automotive fuels for ground vehicles equipped withspark-ignition engines.1.2 This specification describes various characteristics of automotive fuels for use over a wide range of operating conditions.It provides for a variation of the volatility and water tolerance of automotive

4、 fuel in accordance with seasonal climatic changesat the locality where the fuel is used. For the period May 1 through Sept. 15, the maximum vapor pressure limits issued by theUnited States (U.S.) Environmental Protection Agency (EPA) are specified for each geographical area except Alaska and Hawaii

5、.Variation of the antiknock index with seasonal climatic changes and altitude is discussed in Appendix X1.This specification neithernecessarily includes all types of fuels that are satisfactory for automotive vehicles, nor necessarily excludes fuels that can performunsatisfactorily under certain ope

6、rating conditions or in certain equipment. The significance of each of the properties of thisspecification is shown in Appendix X1.1.3 The spark-ignition engine fuels covered in this specification are gasoline and its blends with oxygenates, such as alcoholsand ethers. This specification does not ap

7、ply to fuels that contain an oxygenate as the primary component, such as Fuel Methanol(M85). The concentrations and types of oxygenates are not specifically limited in this specification. However, depending onoxygenate type, as oxygenate content increases above some threshold level, the likelihood f

8、or vehicle problems also increases. Thecomposition of both unleaded and leaded fuel is limited by economic, legal, and technical consideration, but their properties,including volatility, are defined by this specification. In addition, the composition of unleaded fuel is subject to the rules,regulati

9、ons, and Clean Air Act waivers of the U.S. Environmental Protection Agency (EPA). With regard to fuel properties,including volatility, this specification can be more or less restrictive than the EPA rules, regulations, and waivers. Refer toAppendix X3 for discussions of EPA rules relating to fuel vo

10、latility, lead and phosphorous contents, deposit control additivecertification, and use of oxygenates in blends with unleaded gasoline. Contact the EPA for the latest versions of the rules andadditional requirements.1.4 This specification does not address the emission characteristics of reformulated

11、 spark-ignition engine fuel. Reformulatedspark-ignition engine fuel is required in some areas to lower emissions from automotive vehicles, and its characteristics aredescribed in the research report on reformulated spark-ignition engine fuel.2 However, in addition to the legal requirements foundin t

12、his research report, reformulated spark-ignition engine fuel should meet the performance requirements found in thisspecification.1.5 This specification represents a description of automotive fuel as of the date of publication. The specification is undercontinuous review, which can result in revision

13、s based on changes in fuel, automotive requirements, or test methods, or acombination thereof. All users of this specification, therefore, should refer to the latest edition.NOTE 1If there is any doubt as to the latest edition of Specification D4814, contact ASTM International Headquarters.1.6 Tests

14、 applicable to gasoline are not necessarily applicable to its blends with oxygenates. Consequently, the type of fuel underconsideration must first be identified in order to select applicable tests. Test Method D4815 provides a procedure for determiningoxygenate concentration in mass percent. Test Me

15、thod D4815 also includes procedures for calculating mass oxygen content andoxygenate concentration in volume percent. Appendix X4 provides a procedure for calculating the mass oxygen content of a fuelusing measured oxygenate type, oxygenate concentration in volume percent, and measured density or re

16、lative density of the fuel.1 This specification is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.A0.01 on Gasoline and Gasoline-Oxygenate Blends.Current edition approved July 15, 2015Jan. 1, 2016. P

17、ublished August 2015February 2016. Originally approved in 1988. Last previous edition approved in 2015 asD4814 15.D4814 15a. DOI: 10.1520/D4814-15A.10.1520/D4814-16.2 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1347.This

18、 document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior edition

19、s as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. U

20、nited States11.7 The following applies to all specified limits in this standard: For purposes of determining conformance with thesespecifications, an observed value or a calculated value shall be rounded “to the nearest unit” in the right-most significant digit usedin expressing the specification li

21、mit, in accordance with the rounding method of Practice E29. For a specification limit expressedas an integer, a trailing zero is significant only if the decimal point is specified. For a specified limit expressed as an integer, andthe right-most digit is non-zero, the right-most digit is significan

22、t without a decimal point being specified. This convention appliesto specified limits in Tables 1, 3, and Table X8.1,X8.1, and it will not be observed in the remainder of this specification.1.8 The values stated in SI units are the standard, except when other units are specified by U.S. federal regu

23、lation. Values givenin parentheses are provided for information only.NOTE 2Many of the values shown in Table 1 were originally developed using U.S. customary units and were subsequently soft-converted to SI values.As a result, conversion of the SI values will sometimes differ slightly from the U.S.

24、customary values shown because of round-off. In some cases, U.S.federal regulations specify non-SI units.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and

25、 health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric PressureD130 Test Method for Corrosiveness to Copper from Petroleum Products by Co

26、pper Strip TestD287 Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)D381 Test Method for Gum Content in Fuels by Jet EvaporationD439 Specification for Automotive Gasoline (Withdrawn 1990)4D525 Test Method for Oxidation Stability of Gasoline (Induction Period

27、Method)D1266 Test Method for Sulfur in Petroleum Products (Lamp Method)D1298 Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products byHydrometer MethodD2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Sp

28、ectrometryD2699 Test Method for Research Octane Number of Spark-Ignition Engine Fuel3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary pa

29、ge on the ASTM website.4 The last approved version of this historical standard is referenced on www.astm.org.TABLE 1 Vapor Pressure and Distillation Class RequirementsAVapor Pressure/Distillation Class ASTM Test MethodAA A B C D EVapor Pressure,B at 37.8 C (100 F) max, kPa (psi) 54 (7.8) 62 (9.0) 69

30、 (10.0) 79 (11.5) 93 (13.5) 103 (15.0) D4953, D5191,D5482, or D6378Distillation Temperatures, C (F), at % EvaporatedC D8610 volume %, max 70. (158) 70. (158) 65 (149) 60. (140.) 55 (131) 50. (122)50 volume %minD 77 (170.) 77 (170.) 77 (170.) 77 (170.) 77 (170.)E 77 (170.)Emax 121 (250.) 121 (250.) 1

31、18 (245) 116 (240.) 113 (235) 110. (230.)90 volume %, max 190. (374) 190. (374) 190. (374) 185 (365) 185 (365) 185 (365)End Point, max 225 (437) 225 (437) 225 (437) 225 (437) 225 (437) 225 (437)Distillation Residue, volume %, max 2 2 2 2 2 2 D86Driveability Index,F max, C (F) 597 (1250.) 597 (1250.)

32、 591 (1240.) 586 (1230.) 580. (1220.) 569 (1200.) DerivedG,HA See 1.7 for determining conformance with specification limits in this table. When using this table to determine the conformance of gasoline volatility, the reader is advisedto review other applicable national, state, provincial, or local

33、requirements. (For example, in the U.S. these may include the EPA Substantially Similar rule, California AirResources Board (CARB), Clean Burning Gasoline (CBG), other state or local and pipeline specifications). See Appendix X3 for a summary of applicable U.S. EPAregulations for spark-ignition engi

34、ne fuels.B Consult EPA for approved test methods for compliance with EPA vapor pressure regulations.C At 101.3 kPa pressure (760 mm Hg).D Gasolines that may be blended with 1 to 10 volume percent ethanol or all other gasolines whose disposition with ethanol blending is not known shall meet a minimum

35、50 % evaporated distillation temperature of 77 C (170. F) prior to blending with ethanol. Gasoline-ethanol blends that contain 1 to 10 volume percent ethanol shall meeta minimum 50 % evaporated distillation temperature of 66 C (150. F) after blending.E Gasolines known from the origin to retail that

36、will not be blended with ethanol may meet a minimum 50 % evaporated distillation temperature of 66 C (150. F) for volatilityclasses D and E only. Gasolines meeting these limits are not suitable for blending with ethanol.F Driveability Index (DI) = 1.5 T10 + 3.0 T50 + 1.0 T90 + 1.33 C (2.4 F) Ethanol

37、 Volume %, where T10 = distillation temperature, C (F), at 10 % evaporated, T50 =distillation temperature, C (F), at 50 % evaporated,T90 = distillation temperature, C (F), at 90 % evaporated, and 1.33 is the coefficient for the volume % ethanol presentwhen the distillation results are determined in

38、degrees Celsius and 2.4 is the coefficient when distillation results are determined in degrees Fahrenheit.G The DI specification limits are applicable at the refinery or import facility as defined by 40 CFR Part 80.2 and are not subject to correction for precision of the test method.H Since DI is an

39、 index and has no units, the standard temperature conversion from U.S. customary to SI units is not appropriate. The following equation is to be used tomake the conversion: DIC5sDIF2176d/1.8D4814 162D2700 Test Method for Motor Octane Number of Spark-Ignition Engine FuelD2885 Test Method for Determin

40、ation of Octane Number of Spark-Ignition Engine Fuels by On-Line Direct ComparisonTechniqueD3120 Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative MicrocoulometryD3231 Test Method for Phosphorus in GasolineD3237 Test Method for Lead in Gasoline by Atomic

41、Absorption SpectroscopyD3341 Test Method for Lead in GasolineIodine Monochloride MethodD4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density MeterD4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4175 Terminology Relating to Petroleum Pro

42、ducts, Liquid Fuels, and LubricantsD4176 Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures)D4177 Practice for Automatic Sampling of Petroleum and Petroleum ProductsD4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace

43、ContaminationD4806 Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use asAutomotive Spark-Ignition Engine FuelD4815 Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C1 to C4 Alcohols inGasoline by Gas ChromatographyD4953 Test Method for Vapo

44、r Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)D5059 Test Methods for Lead in Gasoline by X-Ray SpectroscopyD5188 Test Method for Vapor-Liquid Ratio Temperature Determination of Fuels (Evacuated Chamber and Piston BasedMethod)D5191 Test Method for Vapor Pressure of Petroleum Produc

45、ts (Mini Method)D5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel,and Engine Oil by Ultraviolet FluorescenceD5482 Test Method for Vapor Pressure of Petroleum Products (Mini MethodAtmospheric)D5500 Test Method for Vehicle Evaluat

46、ion of Unleaded Automotive Spark-Ignition Engine Fuel for Intake Valve DepositFormationD5598 Test Method for Evaluating Unleaded Automotive Spark-Ignition Engine Fuel for Electronic Port Fuel Injector FoulingD5599 Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxyg

47、en Selective FlameIonization DetectionD5842 Practice for Sampling and Handling of Fuels for Volatility MeasurementD5845 Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and tert-Butanol in Gasoline byInfrared SpectroscopyD5854 Practice for Mixing and Handling of Liquid Samp

48、les of Petroleum and Petroleum ProductsD6378 Test Method for Determination of Vapor Pressure (VPX) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method)D6469 Guide for Microbial Contamination in Fuels and Fuel SystemsD6920 Test Method for Total Sulfur in N

49、aphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels byOxidative Combustion and Electrochemical DetectionD7039 Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-EthanolBlends by Monochromatic Wavelength Dispersive X-ray Fluorescence SpectrometryD7220 Test Method for Sulfur inAutomotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray FluorescenceSpectrometryD7667 Test Method for Determination of Corrosiveness to Silver byAutomotive Spark-Ignition