ASTM D3748-2014 Standard Practice for Evaluating High-Density Rigid Cellular Plastics《评价高密度硬质泡沫塑料的标准操作规程》.pdf

《ASTM D3748-2014 Standard Practice for Evaluating High-Density Rigid Cellular Plastics《评价高密度硬质泡沫塑料的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3748-2014 Standard Practice for Evaluating High-Density Rigid Cellular Plastics《评价高密度硬质泡沫塑料的标准操作规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D3748 14Standard Practice forEvaluating High-Density Rigid Cellular Plastics1This standard is issued under the fixed designation D3748; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This practice covers the basic test procedures for deter-mination of the physical properties and reporting of data forhigh-density rigid ce

3、llular plastics.1.2 The values stated in SI units are to be regarded asstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and det

4、ermine the applica-bility of regulatory limitations prior to use.NOTE 1This standard and ISO 9054 address the same subject matter,but differ in technical content.2. Referenced Documents2.1 ASTM Standards:2C177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties b

5、y Means ofthe Guarded-Hot-Plate ApparatusC518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusD149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Electrical Insulating Materialsat Commercial Power FrequenciesD570 Test

6、 Method for Water Absorption of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD695 Test Method for Compressive Properties of RigidPlastic

7、sD696 Test Method for Coefficient of Linear Thermal Expan-sion of Plastics Between 30C and 30C with a VitreousSilica DilatometerD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD883 Terminology Relating to PlasticsD1622 Test Method

8、for Apparent Density of Rigid CellularPlastics3. Terminology3.1 Definitions:3.1.1 high densitygreater than 320 kg/m3(0.32 g/cm3)or20 lb/ft3apparent density.3.1.2 For definitions of other terms used in this practice,refer to Terminology D883.4. Significance and Use4.1 This practice provides appropria

9、te testing methods, anda specific data reporting procedure for high-density rigidcellular plastics.5. Sample Preparation5.1 Prepare samples in one of two ways:(a) process samples directly into proper size specimens, or(b) prepare samples from larger sections as specified ineach individual test.5.2 R

10、eport the precise manner of sample preparation.6. Conditioning6.1 Condition specimens prior to testing in accordance withProcedure A of Practice D618.7. Number of Test Specimens7.1 Cellular plastics are often nonuniform in density distri-bution; therefore, a minimum of five specimens needs to betest

11、ed per testing method to obtain representative values.8. Test Methods8.1 Where technically suitable, reference is made to existingASTM test methods. Otherwise, comments or changes areoutlined in accordance with this practice.8.2 Apparent DensityTest Method D1622.8.3 Compressive StrengthTest Method D

12、695.8.4 Tensile PropertiesTest Method D638.1This practice is under the jurisdiction ofASTM Committee D20 on Plastics andis the direct responsibility of Subcommittee D20.22 on Cellular Materials - Plasticsand Elastomers.Current edition approved March 1, 2014. Published March 2014. Originallyapproved

13、in 1978. Last previous edition approved in 2009 as D3748 09. DOI:10.1520/D3748-14.2For referenced ASTM standards, visit the ASTM Web Site, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary pa

14、ge onthe ASTM web site.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States18.5 Coeffcient of Linear Thermal ExpansionTest MethodD696.8.6 Apparent Flexural PropertiesTest Met

15、hods D790.8.7 Deflection TemperatureTest Method D648.8.8 Dielectric Breakdown Voltage and Dielectric StrengthTest Methods D1498.9 Thermal ConductivityTest Methods C177 or C518.NOTE 2UseTest Method C518 only for materials having densities lessthan 900 kg/m3.8.10 Water Absorption RateTest Method D570.

16、9. Report9.1 Report the following information:9.1.1 Complete identification of the tested material as tomaterial supplier and nomenclature, source of samples, lot orrun number, and type of part.9.1.2 Type of manufacturing process used to make the part,for example, extrusion, injection molding, casti

17、ng, etc.9.1.3 Technique used to prepare the test specimens, forexample, directly-molded or extruded, cut from larger part andedges tensile cut, etc.9.1.4 Number of uncut skins on the specimen when in test(refers to skins not cut in sample preparation).9.1.5 Location of skins (cut and uncut) while th

18、e specimenis in test, that is, horizontal, vertical, none, etc.9.1.6 Dimensions (length, width, thickness) of the speci-men.9.1.7 Apparent density. If the apparent density varies, reportthe maximum, minimum, average, and density within 12.7 mm(0.5 in.) of the test area.9.1.8 Conditioning temperature

19、 and time.9.1.9 Date of the test.10. Keywords10.1 high density; rigid cellular plasticsSUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue (D3748 - 09)that may impact the use of this standard. (March 1, 2014)(1) Revised Section 3.ASTM

20、 International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are ent

21、irely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsan

22、d should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee o

23、n Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D3748 142