ASTM D3260-2001(2005) Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products《适用于工厂的压制铝制品透明涂层的耐酸和耐灰浆标准试验方法》.pdf

《ASTM D3260-2001(2005) Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products《适用于工厂的压制铝制品透明涂层的耐酸和耐灰浆标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3260-2001(2005) Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products《适用于工厂的压制铝制品透明涂层的耐酸和耐灰浆标准试验方法》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3260 01 (Reapproved 2005)Standard Test Method forAcid and Mortar Resistance of Factory-Applied ClearCoatings on Extruded Aluminum Products1This standard is issued under the fixed designation D 3260; the number immediately following the designation indicates the year oforiginal adoptio

2、n or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the evaluation of the mortar andacid resistance of

3、 clear protective coating factory applied toextruded aluminum substrates.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its u

4、se. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 207 Specification for Hydrated Lime for Masonry Pur-posesD 823 Practices

5、 for Producing Films of Uniform Thicknessof Paint, Varnish, and Related Products on Test Panels3. Summary of Test Method3.1 Panels that have been buffed, cleaned, neutralized, andcoated with the material being evaluated are exposed to freshlyprepared mortar and to a hydrochloric acid solution.4. Sig

6、nificance and Use4.1 This test method will provide differentiation betweentypes of coatings for acid and motor resistance providing thecoating is applied in a uniform continuous film with a specifiedfilm thickness.5. Reagents5.1 AcidTen volume percent solution of commercialgrade hydrochloric acid (3

7、1.4 to 31.8 % HCl, 20B) indistilled water.5.2 Cleaning SolutionAn alkaline cleaner3in the concen-tration recommended by the manufacturer, usually 45 to 60 g/L(6 to 8 oz/gal) of water. The pH of the solution should bebetween 11.4 and 12.2.5.3 LimeBuilding lime complying with SpecificationC 207.5.4 Ne

8、utralizing SolutionPrepare from a stable free-flowing, granular material having a chromate base4as recom-mended by the supplier, usually at a concentration of 90 to 120g/L (12 to 16 oz/gal) of water.5.5 SandDry sand capable of passing through a 10-meshwire screen.6. Test Panels6.1 Panels of extruded

9、 aluminum alloy No. 6063-T5 withdimensions 150 by 75 by 6.3 mm (6 by 3 by14 in.) shall beused for the test.7. Procedure7.1 Preparation of Test Panels:7.1.1 Buff the aluminum panels and remove the buffingcompound with an organic solvent.7.1.2 Immerse the panels in cleaning solution (5.2)for1hata temp

10、erature of 93C (200F).7.1.3 Rinse the panels in tap water having a pH of 6.5 to 7.5until the surface is free of water break. Use reagent water forrinsing if the pH of the tap water is outside the specified limits.The panels shall be free from evidence of corrosion or surfaceattack.7.1.4 Immerse the

11、panels in neutralizing solution (5.4)at246 1C (75 6 2F) for 30 s to neutralize any retained alkalinityand to promote adhesion of the applied coatings.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsi

12、bility ofSubcommittee D01.55 on Factory Applied Coatings on Preformed Products.Current edition approved May 15, 2005. Published June 2005. Originallyapproved in 1982. Last previous edition approved in 2001 as D 3260 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact A

13、STM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Diversey No. 808 has been found satisfactory for this purpose.4Diversey No. 814 has been found satisfactory for this purpose.1Copyright ASTM

14、International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.1.5 Rinse the panels in reagent water and allow them todry a minimum of 1 h before coating.7.2 Coating of Test Panels:7.2.1 Apply the coatings being evaluated to the test panelsin a uniform continuou

15、s film by automatic spray equipment inaccordance with Method A of Practices D 823.7.2.2 For the mortar test, spray two panels on one side withtwo or more full wet coats to produce a minimum dry filmthickness of 15 m (0.6 mil ) and two panels with one or morefull wet coats to produce a minimum dry fi

16、lm thickness of 7.5m (0.3 mi).7.2.3 For the acid test, spray two panels with two or morefull wet coats, on both sides, to produce a minimum dry filmthickness of 0.6 mil (15 m) and two panels with one or morefull wet coats on both sides to a minimum dry film thickness of7.5 m ( 0.3 mil).7.2.4 Allow t

17、he panels to dry for 7 days at 23 6 2C (73 63.5F ) and 50 6 5 % relative humidity.7.3 Mortar Test:7.3.1 Prepare freshly mixed mortar by dry mixing 75 g ofbuilding lime (5.3) and 225 g of sand (5.5) and addingsufficient reagent water while stirring to make a soft paste thatcan be formed into a firm m

18、ortar patty approximately 40 mm(112 in.) in diameter and 6 mm (14 in.) thick.7.3.2 Apply the mortar to the top and bottom areas of thetest panels and, without drying, immediately expose them for 7days at 95 to 98 % relative humidity at a temperature of 21 62C (70 6 3.5F) in an automatically controll

19、ed cabinet.7.3.3 At the end of 7 days take the panels from the testcabinet and immediately dislodge the mortar patties from thepanels using a damp cloth to remove any residue.7.3.4 View the surface of the panels perpendicular to thesurface under a diffused light source providing a minimumlight inten

20、sity at the surface of 2150 1x (200 fc). Examine forblistering, peeling, lifting, crazing, flaking, or discoloration ofthe coating, and for corrosion of the coated part of thealuminum panel. Three observers shall evaluate each panel andthe majority assessment shall govern.7.4 Acid Test:7.4.1 Apply a

21、 mixture of 50 parts beeswax and 50 partsparaffin to protect the raw edges to a distance of 10 mm (38 in.).7.4.2 Immerse the panels in the acid bath (5.1)at216 2C(70 6 3.5F ) for 6 h. Remove the panels, rinse in water, andallow to dry.7.4.3 Examine and evaluate as in 7.3.4.8. Precision and Bias8.1 N

22、o information is presented about either the precision orbias of this test method, since the test results are nonquantitave.9. Keywords9.1 acid resistance; differentiation of coatings; extrudedaluminum parts; mortar resistance; uniform continuous filmASTM International takes no position respecting th

23、e validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard i

24、s subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International He

25、adquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This s

26、tandard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3260 01 (2005)2