ASTM D2555-2017a Standard Practice for Establishing Clear Wood Strength Values《用于确定清晰的木材强度值的标准实施规程》.pdf

《ASTM D2555-2017a Standard Practice for Establishing Clear Wood Strength Values《用于确定清晰的木材强度值的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D2555-2017a Standard Practice for Establishing Clear Wood Strength Values《用于确定清晰的木材强度值的标准实施规程》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D2555 17D2555 17aStandard Practice forEstablishing Clear Wood Strength Values1This standard is issued under the fixed designation D2555; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb

2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe development of safe and efficient design values for lumber, laminated timber, plywood, roundtimbers, and other solid wood products, eac

3、h with its own special requirements has, as a commonstarting point, the need for an authoritative compilation of clear wood strength values for thecommercially important species.Also required are procedures for establishing, from these data, valuesapplicable to groups of species or to regional group

4、ings within a species where necessitated bymarketing conditions. This practice has been developed to meet these needs and to provide, inaddition, information on factors for consideration in the adjustment of the clear wood strength valuesto design values for engineering. Since factors such as specie

5、s preference, species groupings,marketing practices, design techniques, and safety factors vary with each type of product and end use,it is contemplated that this practice will be supplemented where necessary by other appropriatestandards relating to specific design values for each such product. Pra

6、ctice D245 is an example of sucha standard applicable to the interpretation of the clear wood strength values in terms of allowableproperties for visually graded lumber.A primary feature of this practice is the establishment of tables presenting the most reliable basicinformation developed on the st

7、rength of clear wood and its variability through many years of testingand experience. The testing techniques employed are those presented in Test Methods D143. Amongthe recognized limitations of such strength data are those resulting from the problems of samplingmaterial from forests extending over

8、large regions, and the uneconomical feasibility of completelytesting an intensive sample. A practical approach to the improvement of strength data is through theapplication of the results of density surveys in which the specific gravity of the entire forest stand foreach species is determined on a s

9、ound statistical basis. Through regression equations derived frompresently available strength data, revised strength values are established from the specific gravity-strength relationship for clear wood. This procedure greatly extends current capabilities to developnew estimates of strength and to i

10、mprove or verify estimates made in the past.1. Scope1.1 This practice covers the determination of strength values for clear wood of different species in the unseasoned condition,unadjusted for end use, applicable to the establishment of design values for different solid wood products such as lumber,

11、 laminatedwood, plywood, and round timbers. Presented are:1.1.1 Procedures by which test values obtained on small clear specimens may be combined with density data from extensiveforest surveys to make them more representative,1.1.2 Guidelines for the interpretation of the data in terms of assigned v

12、alues for combinations of species or regional divisionswithin a species to meet special marketing needs, and1.1.3 Information basic to the translation of the clear wood values into design values for different solid wood products fordifferent end uses.1.1.4 For species where density survey data are n

13、ot as yet available for the re-evaluation of average strength properties, thepresently available data from tests made under the sampling methods and procedures of Test Methods D143 or Practice E105 are1 This practice is under the jurisdiction of ASTM Committee D07 on Wood and are the direct responsi

14、bility of Subcommittee D07.02 on Lumber and Engineered WoodProducts.Current edition approved April 15, 2017Aug. 1, 2017. Published June 2017October 2017. Originally approved in 1966. Last previous edition approved in 20162017 asD2555 16.D2555 17. DOI: 10.1520/D2555-17.10.1520/D2555-17A.This document

15、 is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appr

16、opriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1provided with appropriate provision for their application and

17、 use. Because of the comprehensive manner in which the densitysurvey is undertaken, it follows that the re-evaluated strength data are intended to be representative of the forest stand, or ratherlarge forest subdivisions.1.1.5 Some useful mechanical properties (tensile strengths parallel and perpend

18、icular to grain, modulus of rigidity for alongitudinal-transverse plane, and transverse modulus of elasticity) have not been extensively evaluated. Methods are describedfor estimating these properties by their relation to other properties.1.2 The values stated in inch-pound units are to be regarded

19、as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user o

20、f this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardizationestablished

21、 in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D143 Test Methods for Small Clear Specimens of TimberD245 Practice fo

22、r Establishing Structural Grades and Related Allowable Properties for Visually Graded LumberD2915 Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based ProductsE105 Practice for Probability Sampling of Materials3. Summary of Methods3.1 Two methods are presented for establishing

23、tables of clear wood strength properties for different species and regionalsubdivisions thereof in the unseasoned condition and unadjusted for end use. These are designated Method A and Method B.3.1.1 Method A provides for the use of the results of surveys of wood density involving extensive samplin

24、g of forest trees, incombination with the data obtained from standard strength tests made in accordance withTest Methods D143.The average strengthproperties are obtained from wood density survey data through linear regression equations establishing the relation of specificgravity to the several stre

25、ngth properties.NOTE 1Density surveys have been completed for only a limited number of species. Data are thus not currently available for the use of Method Aon all commercial species. As such data become available they will be incorporated in revisions of this practice.3.1.2 Method B provides for th

26、e establishment of tables of strength values based on standard tests of small clear specimens inthe unseasoned condition for use when data from density surveys are not available. Separate tables are employed to present thedata on woods grown in the United States and on woods grown in Canada.4. Proce

27、dure for Establishing Clear Wood Strength Values4.1 Method ASix steps are involved in establishing strength values by the wood density survey procedure. These are:conducting the wood density survey, development of unit areas, determination of average specific gravity for a unit area,determination of

28、 strength-specific gravity relations, estimation of average strength properties for a unit area, and combining valuesfor unit areas into basic groups and establishing average strength properties and estimates of variance for the groups. In thesemethods a basic group is a combination of unit areas re

29、presenting a species or a regional division thereof.4.1.1 Conducting Wood Density SurveyAwell-designed and thorough wood density survey is required to provide needed dataon specific gravity for the reevaluation of strength properties. Such a survey requires consideration of the geographic range to b

30、ecovered, the representativeness of the sample, the techniques of density evaluation, and adequate data analysis.NOTE 2Detailed information on an acceptable method of conducting wood density surveys, together with survey data, are presented in the U.S. ForestService Research Paper FPL 27 (1).34.1.2

31、Development of Unit AreasSubdivide the geographical growth range of each species into unit areas that contain 1 % ormore of the estimated cubic foot volume of standing timber of the species and are represented by reliable estimates of specificgravity of at least 20 trees. Make up unit areas of U.S.

32、Forest Service Survey Units, or similar units or subdivisions of units, forwhich reliable estimates of timber volume are available. Develop unit areas objectively by means of the following steps:4.1.2.1 Select a base survey unit or subdivision of a survey unit to be grouped with others,4.1.2.2 Group

33、 with similar adjacent areas to make up a unit area on the basis of a timber volume, and4.1.2.3 Determine the number of tree specific gravity samples available in the proposed unit area.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceast

34、m.org. For Annual Book of ASTM Standardsvolume information, refer to the standardsstandards Document Summary page on the ASTM website.3 The boldface numbers in parentheses refer to a list of references at the end of this standard.D2555 17a2NOTE 3The rules for developing unit areas should represent a

35、n effort to subdivide objectively and uniquely the range of a species into smallgeographic areas, which are assumed to be considerably more homogeneous with respect to the mechanical properties of the species than is the entirerange itself. The number of unit areas associated with a species is a fun

36、ction of the volume of timber on the smallest usable areas and the number of treespecific gravity samples taken. In general, the larger the range and the greater the commercial importance of the species, the greater are the number ofunfit areas. One acceptable procedure for establishing unit areas i

37、s presented in Appendix C of U.S. Forest Service Research Paper FPL 27 (1).4.1.3 Determination of Average Specific Gravity for a Unit AreaCalculate the average specific gravity of trees in each unitarea as the simple average of individual estimates of specific gravity of trees within the unit area.4

38、.1.4 Determination of Strength-Specific Gravity RelationsFrom matched specific gravity and strength data on small clearspecimens of wood, establish relationships of the form:y 5a1bx (1)where:y = estimated strength value,a, b = constants for the species, andx = specific gravity of the species.for eac

39、h species, using standard statistical methods of regression analysis. Equations for modulus of rupture, modulus ofelasticity, maximum crushing strength, and maximum shearing strength are established in this manner. The distribution of specificgravity in the samples used to compute regressions should

40、 be representative of the species and, in particular, shall represent thefull specific gravity range. The nature of the true distribution of specific gravity can be obtained from results of wood densitysurveys. Obtain the data from specimens tested in accordance with Test Methods D143.4.1.4.1 Severa

41、l methods are available for securing suitable samples for obtaining data to compute strength-specific gravityrelationships, as follows: strength and specific gravity values from samples obtained in conformance with Test Methods D143 maybe employed solely or in combination with data secured by sampli

42、ng techniques described below or test samples may be obtainedfrom the forest resource in the form of trees, logs, or lumber. Select samples that are representative of all growing stock from eachof at least five different locations within the growth range of a species that include the scope of enviro

43、nmental conditions of therange. This implies that the sample from a single location must be such that all of the growing stock from that location isrepresented.4.1.4.2 Where relationships between strength and specific gravity are shown to have a statistically significant difference at the5 % level w

44、ithin a species growth range, subdivide the range to permit the development of more accurate estimating equations foreach subdivision. Develop equations for subdivisions of a species growth range only if specimens from at least five distinctlydifferent places in the proposed subdivision are availabl

45、e and if the correlation coefficients from the strength-specific gravityregressions are 0.50 or greater.4.1.5 Estimation of the Average Strength Properties for a Unit AreaGiven a set of strength-specific gravity estimatingequations for each species or subdivision thereof, compute average strength pr

46、operties for each unit area using these equations andthe average specific gravity for the unit area.4.1.6 Combining Unit Areas into Basic Groups and Development of Average Strength Properties and Estimates of Variance forthe GroupsCombine all unit areas containing timber whose properties are describ

47、ed by the same strength-specific gravityrelationships to produce a basic group of unit areas. Develop the following information for these basic groups:4.1.6.1 For each unit area, obtain, from reliable volume data, the volume of the species being considered and estimate strengthproperties from approp

48、riate equations. Determine average strength properties for a group of unit areas for a species or a subdivisionthereof by the following equation:Y% 5(i Y iVi/V! (2)where:Y5 = weighted average strength property for the group of unit areas,Yi = average strength property for the ith unit area,VI = perc

49、entage of standing timber volume of the species for the ith unit area, andV = total percentage of standing timber volume of the species in the group of unit areas being combined.4.1.6.2 Compute the variability index, which is a measure of the homogeneity among average values for unit areas within agroup, by dividing the group average by the lowest unit area average included in the group.4.1.6.3 Estimate a standard deviation, providing a measure of the dispersion of individual strength values about the groupaverage, for each basic group of unit areas using informati