ASTM C616 C616M-2010 Standard Specification for Quartz-Based Dimension Stone《砂岩规格料标准规格》.pdf

《ASTM C616 C616M-2010 Standard Specification for Quartz-Based Dimension Stone《砂岩规格料标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C616 C616M-2010 Standard Specification for Quartz-Based Dimension Stone《砂岩规格料标准规格》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C616/C616M 10Standard Specification forQuartz-Based Dimension Stone1This standard is issued under the fixed designation C616/C616M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in

2、 parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the material characteristics,physical

3、 requirements, and sampling appropriate to the selec-tion of quartz-based dimension stone for general building andstructural purposes. Refer to Guides C1242 and C1528 for theappropriate selection and use of quartz-based dimension stone.1.2 Quartz-based dimension stone shall include stone that issawe

4、d, cut, split, or otherwise finished or shaped, and shallspecifically exclude molded, cast, or otherwise artificiallyaggregated units composed of fragments, and also crushed andbroken stone.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The val

5、ues stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2C97/C97M Test Methods for Absorption and Bulk Specific

6、Gravity of Dimension StoneC99/C99M Test Method for Modulus of Rupture of Dimen-sion StoneC119 Terminology Relating to Dimension StoneC170/C170M Test Method for Compressive Strength ofDimension StoneC241/C241M Test Method for Abrasion Resistance ofStone Subjected to Foot TrafficC1242 Guide for Select

7、ion, Design, and Installation ofDimension Stone Attachment SystemsC1353 Test Method for Abrasion Resistance of DimensionStone Subjected to Foot Traffic Using a Rotary Platform,Double-Head AbraserC1528 Guide for Selection of Dimension Stone3. Terminology3.1 DefinitionsAll definitions are in accordanc

8、e with Ter-minology C119.4. Classification4.1 Quartz-based dimension stone sandstone shall be clas-sified according to the free silica content as follows:4.1.1 I Sandstone, with 60 % minimum free silica content.34.1.2 II Quartzitic Sandstone, with 90 % minimum freesilica content.4.1.3 III Quartzite,

9、 with 95 % minimum free silica content.5. Physical Properties5.1 Quartz-based dimension stone supplied under this speci-fication shall conform to the physical requirements in Table 1.5.2 Quartz-based dimension stone shall be sound, durable,and free of spalls, cracks, open seams, pits, or other defec

10、ts thatare likely to impair its structural integrity in its intended use.5.3 The desired color and texture, with their permissiblenatural variations in material characteristics for all material tobe produced for the project, shall be established by controlsamples. Select representative samples by vi

11、ewing a sufficientnumber of physical samples prior to production that show thecomplete range of variations in color and texture of thequartz-based dimension stone specified.6. Sampling6.1 Samples, if required, for testing to determine the char-acteristics and physical properties shall be representat

12、ive of thequartz-based dimension stone to be used.7. Keywords7.1 ashlar; Bluestone; Quartzite; Sandstone1This specification is under the jurisdiction of ASTM Committee C18 onDimension Stone and is the direct responsibility of Subcommittee C18.03 onMaterial Specifications.Current edition approved Sep

13、t. 1, 2010. Published October 2010. Originallyapproved in 1968. Last previous edition approved in 2008 as C616 08. DOI:10.1520/C0616_C0616M-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandardsvol

14、ume information, refer to the standards Document Summary page onthe ASTM website.3Free silica consists of detrital quartz grains plus authigenic silica.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no posit

15、ion respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibilit

16、y.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM

17、 International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address s

18、hown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-8

19、32-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Physical RequirementsNOTEThe values in Table 1 were established using samples prepared accord

20、ing to the individual test methods. Finishes, other than those specifiedin the individual test methods, may result in a deviation from established values.Property Test Requirements Classifications Test Method(s)Absorption by weight, max, % 8 I Sandstone C97/C97M3 II Quartzitic Sandstone1 III Quartzi

21、teDensity, min, lb/ft3kg/m3 125 2000 I Sandstone C97/C97M150 2400 II Quartzitic Sandstone160 2560 III QuartziteCompressive strength, min, psi (MPa) 4000 28 I Sandstone C170/C170M10000 69 II Quartzitic Sandstone20000 140 III QuartziteModulus of rupture min, psi (MPa) 350 2.4 I Sandstone C99/C99M1000

22、6.9 II Quartzitic Sandstone2000 13.8 III QuartziteAbrasion resistance, min HaA,B,C2DI Sandstone C241/C241M/C13538 II Quartzitic Sandstone8 III QuartziteAPertains only to stone subject to foot traffic.BThe supplier of the abrasive, Norton, has indicated that the formula for No. 60 Alundum abrasive (N

23、orton Treatment 138S) has been changed. The new abrasive iscurrently more aggressive, resulting in lower Havalues than when the standard was initially established. As such, care should be taken when interpreting Hatest results,both with regard to this standard and with regard to historical data from

24、 the same quarry source. Committee C18 is actively studying alternatives to deal with this issue.CAbrasion Resistance Test Method C1353 will eventually replace Test Method C241/C241M and it is not necessary to perform both tests. Availability of the properequipment and materials by the testing laboratory may determine which test is performed.DNot recommended for paving in areas subject to heavy foot traffic.C616/C616M 102