ASTM C1527 C1527M-2011(2018) Standard Specification for Travertine Dimension Stone《石灰华尺寸石的标准规格》.pdf

《ASTM C1527 C1527M-2011(2018) Standard Specification for Travertine Dimension Stone《石灰华尺寸石的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1527 C1527M-2011(2018) Standard Specification for Travertine Dimension Stone《石灰华尺寸石的标准规格》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1527/C1527M 11 (Reapproved 2018)Standard Specification forTravertine Dimension Stone1This standard is issued under the fixed designation C1527/C1527M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the year of last r

2、evision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the material characteristics,physical requirements, and sampling appropriate to the selec-tion of

3、travertine for general building and structural purposes.Refer to Guides C1242 and C1528 for the appropriate selectionand use of travertine dimension stone.1.2 Dimension travertine shall include stone that is sawed,cut, split, or otherwise finished or shaped and shall specificallyexclude molded, cast

4、, or otherwise artificially aggregated unitscomposed of fragments, and also crushed and broken stone.1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be use

5、d independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment o

6、f International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C97/C97M Test Methods for Absorption and Bulk SpecificGravity of Dimension StoneC99/C99M Test Method for Modulus of Rupt

7、ure of Dimen-sion StoneC119 Terminology Relating to Dimension StoneC170/C170M Test Method for Compressive Strength ofDimension StoneC241/C241M Test Method for Abrasion Resistance of StoneSubjected to Foot TrafficC880/C880M Test Method for Flexural Strength of Dimen-sion StoneC1242 Guide for Selectio

8、n, Design, and Installation ofDimension Stone Attachment SystemsC1353 Test Method for Abrasion Resistance of DimensionStone Subjected to Foot Traffic Using a Rotary PlatformAbraserC1528 Guide for Selection of Dimension Stone3. Terminology3.1 All definitions are in accordance with TerminologyC119.3.2

9、 Definitions:3.2.1 fleuri-cut (cross-cut), adjdescribes stone that is cutparallel to the natural veining.3.2.2 vein-cut, adjdescribes stone that is cut perpendicularto the natural veining.4. Physical Properties4.1 Travertine supplied under this specification shall con-form to the physical requiremen

10、ts prescribed in Table 1.4.2 Travertine shall be free of minerals that may causeobjectionable staining under normal environments of use.4.3 Voids in travertine are a natural characteristic of thematerial and shall be considered in assessing the permissiblenatural variations suitable for a particular

11、 application.4.3.1 Some travertines may not be suitable for exterior usein areas subject to frequent freeze-thaw cycles.4.3.2 Travertine that is fleuri-cut (cross-cut) rather thanvein-cut can be expected to experience certain problems,because some areas of the exposed surface will consist of onlya t

12、hin layer of stone that covers a void in the stone.4.4 The desired color and texture, with their permissiblenatural variations in material characteristics for material to beproduced for the project, shall be established by controlsamples. Representative samples shall be selected prior toproduction b

13、y viewing a sufficient number of samples thatshow the complete range of variations in color and texture ofthe travertine specified.1This specification is under the jurisdiction of ASTM Committee C18 onDimension Stone and is the direct responsibility of Subcommittee C18.03 onMaterial Specifications.C

14、urrent edition approved Jan. 1, 2018. Published January 2018. Originallyapproved in 2002. Last previous edition approved in 2011 as C1527/C1527M- 11.DOI: 10.1520/C1527-11R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For

15、Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with international

16、ly recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. Sampling5.1 Samples, if required, for testing to dete

17、rmine the char-acteristics and physical properties shall be representative of thetravertine to be used.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that d

18、etermination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved

19、 or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel

20、that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprin

21、ts (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copy

22、right Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Physical RequirementsNOTE 1The material property values in Table 1 were established using samples prepared according to the individual Test Methods. Finishes, otherthan those specified in the individual test

23、methods, may result in a deviation from established values.NOTE 2Vein-cut specimens tested with load applied to bend specimens parallel to the veins (weak direction).Physical Property Test Requirements Classifications Test MethodsAbsorption by weight, max, % 2.52.5I ExteriorII InteriorC97/C97MDensit

24、y, min, lb/ft3kg/m3 144 2300144 2300I ExteriorII InteriorC97/C97MCompressive strength, min, psi (MPa) 7500 525000 34I ExteriorII InteriorC170/C170MAbrasion resistance, min, HaA,B,C1010I ExteriorII InteriorC241/C241M/C1353Flexural strength, min, psi (MPa) (Note 2) 500 3.4500 3.4I ExteriorII InteriorC

25、880/C880MAPertains to foot traffic only. Where two or more stone varieties are combined for color and design effects, there should be no greater difference than five points in abrasionresistance.BThe supplier of the No. 60 Alundum abrasive, Norton, has indicated that the formula for Norton treatment

26、 138S has been changed. The new abrasive is currently moreaggressive, resulting in lower abrasion resistance values (Ha) than when the standard was initially established. As such, care should be taken when interpreting Havaluesfrom tests using the new abrasive, particularly with regard to currentAST

27、M stone standard specification requirements for abrasion resistance, which were developed whenthe original abrasive was still in use.CIt is not necessary to perform both tests. Availability of the proper equipment and materials by the testing laboratory may determine which test is performed.C1527/C1527M 11 (2018)2