ASTM A608 A608M-2006 Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperature《高温受压离心铸造的铁铬镍高合金钢管标准规范》.pdf

《ASTM A608 A608M-2006 Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperature《高温受压离心铸造的铁铬镍高合金钢管标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A608 A608M-2006 Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperature《高温受压离心铸造的铁铬镍高合金钢管标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 608/A 608M 06Standard Specification forCentrifugally Cast Iron-Chromium-Nickel High-Alloy Tubingfor Pressure Application at High Temperatures1This standard is issued under the fixed designationA 608/A 608M; the number immediately following the designation indicates the yearof original

2、 adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defen

3、se.1. Scope*1.1 This specification covers iron-chromium-nickel, high-alloy tubes made by the centrifugal casting process intendedfor use under pressure at high temperatures.1.2 The grades of high alloys detailed in Table 1 areintended for applications requiring strength and resistance tocorrosion an

4、d scaling at high temperatures.1.3 Optional Supplementary Requirements S1 to S11 areprovided; these call for additional tests to be made if desired.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in bracket

5、s. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of each other. Combining values fromthe two systems may result in nonconformance with thespecification.2. Referenced Documents2.1 ASTM Standards:2A 342/A 342M Test Methods for Permeability

6、of FeeblyMagnetic MaterialsA 488/A 488M Practice for Steel Castings, Welding, Quali-fications of Procedures and PersonnelA 999/A 999M Specification for General Requirements forAlloy and Stainless Steel PipeE8 Test Methods for Tension Testing of Metallic MaterialsE21 Test Methods for Elevated Tempera

7、ture Tension Testsof Metallic MaterialsE94 Guide for Radiographic ExaminationE 139 Test Methods for Conducting Creep, Creep-Rupture,and Stress-Rupture Tests of Metallic MaterialsE 142 Method for Controlling Quality of RadiographicTesting3E 151 Recommended Practice for Tension Tests of MetallicMateri

8、als at Elevated Temperatures With Rapid Heatingand Conventional or Rapid Strain Rates3E 165 Test Method for Liquid Penetrant ExaminationE 340 Test Method for Macroetching Metals and Alloys3. Ordering Information3.1 Orders for material to this specification should includethe following, as required, t

9、o describe the desired materialadequately:3.1.1 Quantity (feet, centimetres, or number of lengths),3.1.2 Name of material (centrifugally cast tubing),3.1.3 Specification number and grade (Table 1),3.1.4 Size (outside or inside diameter and minimum wallthickness, see Section 8).3.1.5 Condition (see S

10、ection 9, as cast or as cast withmachining on outside or inside surfaces, or machined; see 5.1,8, and 9),3.1.6 Length (specific or random), (Permissible Variationsin Length Section of Specification A 999/A 999M),3.1.7 End finish (Ends Section of Specification A 999/A 999M),3.1.8 Optional requirement

11、s (see 8.2.3 regarding the manu-facturers wall thickness allowance for as cast tubing andSupplementary Requirements S1 to S11),3.1.9 Test report required (see Section 13), and1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys, and is the d

12、irect responsibility of SubcommitteeA01.18 on Castings.Current edition approved Sept. 1, 2006. Published September 2006. Originallyapproved in 1970. Last previous edition approved in 2002 as A 608/A 608M 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer

13、 Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consh

14、ohocken, PA 19428-2959, United States.3.1.10 Special requirements to be added to the specification.4. General Requirements4.1 Material furnished under this specification shall con-form to the applicable requirements of the current edition ofSpecification A 999/A 999M, unless otherwise providedherein

15、.5. Materials and Manufacture5.1 The tubing may be supplied in the as cast condition or ascast with machining on the outside or inside surfaces, ormachined, as agreed upon between the manufacturer and thepurchaser.5.2 Heat treatment of the tubing shall not be required underthis specification.6. Chem

16、ical Requirements6.1 The material shall conform to the requirements as tochemical composition as prescribed in Table 1.7. Tensile Properties7.1 Tension tests at room temperature are not recommendedas acceptance criteria under this specification since the alloysare intended for elevated-temperature s

17、ervice, and room-temperature tests do not have a dependable relationship toelevated-temperature properties. (Where the design of thetubing is based on an assumption of certain minimum creep-rupture properties, one of the supplementary requirements ofthis specification may be stipulated on the order

18、to ascertain theability of the material to meet the design properties.)8. Permissible Variation in Dimensions8.1 Machined Tubing (Tubing Machined on Inside andOutside):8.1.1 The tolerances given in Specification A 999/A 999Mshall govern, except that the wall thickness shall not vary overthe specifie

19、d minimum wall thickness by more than 10 % or116 in. 1.6 mm, whichever is greater. There shall be novariation under the specified minimum wall thickness.8.2 As-Cast Tubing (No Machining or Machined on Insideor Outside):8.2.1 Outside Diameter (For Tubes Ordered to OutsideDiameter):8.2.1.1 Tubes machi

20、ned on the outside shall meet therequirements of Specification A 999/A 999M.8.2.1.2 Tubes not machined on the outside shall meet thepermissible variations of Table 2.8.2.2 Inside Diameter (For Tubes Ordered to Inside Diam-eter):8.2.2.1 Tubes machined on the inside shall meet the require-ments of Spe

21、cification A 999/A 999M.8.2.2.2 Tubes not machined on the inside shall have permis-sible variations as agreed upon by the purchaser and themanufacturer.8.2.3 Wall ThicknessThe wall thickness shall not exceedthe calculated minimum as cast wall thickness by more than thelimits shown in Table 3. The ca

22、lculated minimum wall thick-ness shall be equal to the specified minimum wall thicknessplus the manufacturers allowance for “inside surface feedmetal” and outside surface roughness. Upon request, themanufacturers allowance shall be furnished to the purchaser.There shall be no variation under the cal

23、culated minimum ascast wall thickness. For tubes over 24 up to and including 54 in.600 to 1350 mm in diameter the “permissible variations overspecified minimum as cast wall thickness” shall be agreed uponby the manufacturer and the purchaser.8.2.4 LengthIf definite lengths are ordered, no length oft

24、ubing shall be under the length specified and not longer thanthe tolerance shown in Table 4.TABLE 1 Chemical RequirementsGrade Composition, %Carbon Manganese Silicon Chromium Nickel Phosphorus Sulfur MolybdenumHC30 0.250.35 0.51.0 0.502.00 2630 4.0 max 0.04 max 0.04 max 0.50 maxHD50 0.450.55 1.50 ma

25、x 0.502.00 2630 47 0.04 max 0.04 max 0.50 maxHE35 0.300.40 1.50 max 0.502.00 2630 811 0.04 max 0.04 max 0.50 maxHF30 0.250.35 1.50 max 0.502.00 1923 912 0.04 max 0.04 max 0.50 maxHH30 0.250.35 1.50 max 0.502.00 2428 1114 0.04 max 0.04 max 0.50 maxHH33A0.280.38 1.50 max 0.502.00 2426 1214 0.04 max 0.

26、04 max 0.50 maxHI35 0.300.40 1.50 max 0.502.00 2630 1418 0.04 max 0.04 max 0.50 maxHK30 0.250.35 1.50 max 0.502.00 2327 1922 0.04 max 0.04 max 0.50 maxHK40 0.350.45 1.50 max 0.502.00 2327 1922 0.04 max 0.04 max 0.50 maxHL30 0.250.35 1.50 max 0.502.00 2832 1822 0.04 max 0.04 max 0.50 maxHL40 0.350.45

27、 1.50 max 0.502.00 2832 1822 0.04 max 0.04 max 0.50 maxHN40 0.350.45 1.50 max 0.502.00 1923 2327 0.04 max 0.04 max 0.50 maxHT50 0.400.60 1.50 max 0.502.00 1519 3337 0.04 max 0.04 max 0.50 maxHU50 0.400.60 1.50 max 0.502.00 1721 3741 0.04 max 0.04 max 0.50 maxHW50 0.400.60 1.50 max 0.502.00 1014 5862

28、 0.04 max 0.04 max 0.50 maxHX50 0.400.60 1.50 max 0.502.00 1519 6468 0.04 max 0.04 max 0.50 maxAManufacturing control should ensure that this composition contain a minimal amount of ferrite. See Supplementary Requirement S5.TABLE 2 Permissible Variations in As-Cast Outside DiameterSpecified Outside

29、Diameter of TubingPermissible Plus or MinusVariations from SpecifiedOutside Diameterin. mm in. mmFrom 2 to 4 50 to 100 0.08 2.0Over 4 to 12 100 to 300 0.10 2.5Over 12 to 24 300 to 600 0.12 3.0Over 24 to 36 600 to 900 0.16 4.1Over 36 to 54 900 to 1350 0.25 6.4A 608/A 608M 0629. Finish9.1 Machined Tub

30、ingAll tubes shall be reasonablystraight and free of rejectable indications. All visual irregulari-ties shall be explored for depths. When the depth encroaches onthe specified minimum wall thickness, such irregularities shallbe considered rejectable indications.9.2 As-Cast Tubing:9.2.1 The outside s

31、urface shall be adequately cleaned (suchas by shotblasting, sandblasting, wire brushing, grinding, ormachining). The metal surface so revealed shall be visuallyinspected and shall be free of linear discontinuities or otherimperfections that encroach on the specified minimum wall ofthe tube.9.2.2 Var

32、ious degrees of surface roughness occur on unma-chined tubing. If a specific surface finish is required, it shall bea matter of agreement between the manufacturer and thepurchaser.9.3 Surface Irregularities Not Classified as RejectableVisual surface defects that have been explored and that do notenc

33、roach on the minimum sound wall thickness shall beblended either by machining or grinding the surface into thesurrounding unaffected surface area of the tubing.9.4 Repair by WeldingRepair of injurious defects bywelding shall be permitted and major weld repairs shall bepermitted only subject to the a

34、pproval of the purchaser. Weldrepairs shall be considered major if the depth of the cavityprepared for welding exceeds 20 % of the required minimumwall thickness or if the total surface area exceeds 10 in.265cm2. Defects shall be completely removed before welding. Ifdefects are linear, complete remo

35、val shall be checked by liquidpenetrant inspection (Practice E 165). Only qualified operatorsand procedures in accordance with Practice A 488/A 488Mshall be used. All weld repairs shall be subjected to the sameinspection standard as the tubing.10. Pressure Test10.1 All tubing shall be subjected to a

36、n internal air pressureof at least 75 psi 515 kPa for at least 1 min either whilesubmerged in clear water or with the entire outer surface coatedwith sulfur-free soap suds at the discretion of the manufacturer.In the usable portion of the tube, leaks are not permitted. If theHydrostatic Test, Supple

37、mentary Requirement S6, is invoked,the exact details of the test and testing procedure shall beclearly defined and made a part of the Ordering Information(3.1.8).10.2 Leaks may be repaired by welding only if such repairis approved by the purchaser.11. Flattening Test11.1 Flattening tests are not req

38、uired since material coveredby this specification is not intended to be bent, flanged, orotherwise formed.12. Mechanical Tests Required12.1 Air Pressure TestEach length of tubing shall besubjected to the pressure test described in Section 10.13. Certification13.1 Upon request of the purchaser in the

39、 contract or order,a manufacturers certification that the material was manufac-tured and tested in accordance with this specification togetherwith a report of the test results shall be furnished at the time ofshipment.14. Product Marking14.1 In addition to the marking prescribed in SpecificationA 99

40、9/A 999M, the marking shall include the length, anadditional symbol “S” if the tubing conforms to the supple-mentary requirements specified in Supplementary Require-ments S1 to S11, and the heat number or manufacturersnumber by which the tube can be identified, and, when as cast(see 8.2), the notati

41、on “AS CAST.”15. Keywords15.1 alloy; centrifugal casting; high temperatures; pressurecontaining parts; steel tube; temperature service applicationsTABLE 3 Permissible Variations in As-Cast Wall ThicknessSpecified Outside Diameter of TubingPermissible Variations overCalculated Minimum As-Cast Wall Th

42、icknessin. mm in. mmFrom 2 to 6 50 to 150 0.08 2.0Over 6 to 12 150 to 300 0.10 2.5Over 12 to 24 300 to 600 0.13 3.3TABLE 4 Excess Length Tolerances for Centrifugally Cast TubesOutside Diameter of TubePermissibleExcess Lengthin. mm in. mmFrom2to12 50to30014 6.4Over 12 to 24 300 to 60012 13Over 24 to

43、54 600 to 1350 1 25A 608/A 608M 063SUPPLEMENTARY REQUIREMENTSOne or more of the following supplementary requirements may become a part of the specificationwhen specified on the inquiry or invitation to bid, and purchase order or contract.S1. Product AnalysisS1.1 Product analysis may be made on any l

44、ength of tubing.Individual lengths failing to conform to the chemical require-ments shall be rejected. For product analysis the outsidesurface of the tube shall be ground clean before sampling anda sample taken from this area by drilling. If drillings are taken,the drill should penetrate at least to

45、 the mid point of the tubewall, but the inner18 in. 3 mm of the tube wall shall not beincluded in the sample unless the tube has been bored.S2. Short-Time, High-Temperature Tension TestS2.1 Short-time, high-temperature tension tests shall bemade from a longitudinal or transverse section cut from the

46、 endof the tubing representing each heat or lot as agreed uponbetween the manufacturer and the purchaser.S2.2 The test specimen shall conform to the dimensionsshown in Fig. 7 or 9 of Test Methods E8, or as described inPractice E 151. The specimen gage diameter shall not encroachon the zone of feed m

47、etal when cut from an as-cast tube.S2.3 The specimen shall be subjected to a short-time tensiontest at a temperature of 1400 F 760 C, 1600 F 870 C,1800 F 980 C, or 2000 F 1095 C, as selected by thepurchaser. During the test the temperature range shall bemaintained within 6 10 F 5.5 C at the selected

48、 temperature.If the temperature is not specified by the purchaser, the testshall be conducted at 1600 F 870 C. Processing by heattreatment to improve the hot tensile strength of the material orspecimen shall not be permitted. However, the specimens maybe aged for 24 h at test temperature before test

49、ing.S2.4 The test shall be made in accordance with PracticeE21except that the speed of the head of the testing machineshall be so adjusted that the cross-head speed shall not exceed0.05 in. 1.3 mm/in. 25 mm/min.S2.5 The test specimens shall conform to properties agreedupon between the manufacturer and the purchaser. The valuesshown in Table S2 may be used as a guide.S3. Stress Rupture TestS3.1 The stress rupture test shall be made from a longitu-dinal or transverse s