ASTM A533 A533M-2016 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered Manganese-Molybdenum and Manganese-Molybdenum-Nickel《经回火和淬火的压力容器用锰钼和锰钼镍合金钢板.pdf

《ASTM A533 A533M-2016 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered Manganese-Molybdenum and Manganese-Molybdenum-Nickel《经回火和淬火的压力容器用锰钼和锰钼镍合金钢板.pdf》由会员分享，可在线阅读，更多相关《ASTM A533 A533M-2016 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered Manganese-Molybdenum and Manganese-Molybdenum-Nickel《经回火和淬火的压力容器用锰钼和锰钼镍合金钢板.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A533/A533M 16 Used in USDOE-NE StandardsStandard Specification forPressure Vessel Plates, Alloy Steel, Quenched andTempered, Manganese-Molybdenum and Manganese-Molybdenum-Nickel1This standard is issued under the fixed designation A533/A533M; the number immediately following the designat

2、ion indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by age

3、ncies of the U.S. Department of Defense.1. Scope*1.1 This specification2covers one type of manganese-molybdenum and four types of manganese-molybdenum-nickel alloy steel plates for use in the quenched and temperedcondition for the construction of welded pressure vessels.1.2 Material under this speci

4、fication is available in fivetypes, designated “A”, “B”, “C”, “D”, and “E”. The material isalso available in three classes having the following strengthlevels.ClassTensile Strength,ksi MPa1 80100 550 to 6902 90115 620 to 7953 100125 690 to 8601.3 The maximum thickness of Class 1 and Class 2 plates i

5、slimited only by the capacity of the composition to meet thespecified mechanical property requirements; however, currentpractice normally limits the maximum thickness to 12 in. 300mm for Types A through D and to 7 in. 180 mm for Type E.1.4 The maximum thickness of Class 3 plates is 212 in. 65mm for

6、Types A through D and 2 in. 50 mm for Type E.1.5 The minimum nominal thickness of plates of all classesis 0.25 in. 6.5 mm.1.6 These alloy steel plates in the as-rolled condition aresensitive to cracking during transit and handling, particularly inthicknesses over about 1 or 2 in. 25 or 50 mm. They s

7、houldbe shipped in the as-rolled conditions only by mutual agree-ment of manufacturer and the purchaser.1.7 Plates covered by this specification are often used in thebeltline region of nuclear reactor vessels where the materialproperties may be affected by high levels of radiation. Appen-dix X1 prov

8、ides some information pertinent to this usage.1.8 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used indep

9、endently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.2. Referenced Documents2.1 ASTM Standards:3A20/A20M Specification for General Requirements for SteelPlates for Pressure VesselsA435/A435M Specification for Straight-Beam UltrasonicExamina

10、tion of Steel PlatesA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Steel PlatesA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tions3. General Requirements and Ordering Information3.1 Material supplied to this material s

11、pecification shallconform to Specification A20/A20M. These requirements out-line the testing and retesting methods and procedures, permit-ted variations in dimensions, and mass, quality and repair ofdefects, marking, loading, and ordering information.3.2 In addition to the basic requirements of this

12、specification, certain supplementary requirements are availablewhen additional control, testing, or examination is required tomeet end use requirements. The purchaser is referred to thelisted supplementary requirements in this specification and tothe detailed requirements in Specification A20/A20M.1

13、This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure Vessels.Current edition approved May 1, 2016. Published May 2016. Originallyapproved in 1965.

14、 Last previous edition approved in 2014 as A533/A533M 09(2014). DOI: 10.1520/A0533_A0533M-16.2For ASME Boiler and Pressure Vessel Code applications, see related Specifi-cation SA-533/SA-533M in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact AS

15、TM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoh

16、ocken, PA 19428-2959. United States13.3 If the requirements of this specification are in conflictwith the requirements of Specification A20/A20M, the require-ments of this specification shall prevail.4. Manufacture4.1 Steelmaking PracticeThe steel shall be killed andshall conform to the fine austeni

17、tic grain requirement ofSpecification A20/A20M.5. Heat Treatment5.1 All plates shall be heat treated by heating to a suitabletemperature within the range from 1550 to 1800F 845 to980C, holding for a sufficient time to obtain uniform tem-perature throughout the plate thickness and then quenching, inw

18、ater. Subsequently the plates shall be tempered at a suitabletemperature to produce the specified properties, but not lessthan 1100F 595C with a minimum holding time of12 h in.1.2 min/mm of thickness, but not less than12 h.5.2 When the plates are heat treated by the fabricator, itshall be his respon

19、sibility to apply the proper heat treatmentand to conduct tests he deems necessary to assure that thespecified properties are attained. Plates thicker than 2 in. 50mm shall be stress-relieved by the manufacturer prior toshipment at a temperature no lower than 1100F 595C.6. Chemical Requirements6.1 T

20、he steel shall conform to the chemical requirementsshown in Table 1 unless otherwise modified in accordance withSupplementary Requirement S17, Vacuum Carbon-DeoxidizedSteel, in Specification A20/A20M.7. Mechanical Requirements7.1 Tension Test Requirements:7.1.1 The material as represented by the ten

21、sion-test speci-mens shall conform to the requirements shown in Table 2.7.1.2 For nominal plate thicknesses of34 in. 20 mm andunder, the 112-in. 40 mm wide rectangular specimen may beused, and the elongation may be determined in a 2-in. 50-mmgage length that include the fracture and that shows the g

22、reatestelongation.8. Keywords8.1 alloy steel; alloy steel plate; pressure containing parts;pressure vessel steels; steel plates; steel plates for pressurevesselsSUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not apply unless specified in the order.Alist of standardized supplementary requ

23、irements for use at the option of the purchaser are includedin Specification A20/A20M. Several of those considered suitable for use with this specification arelisted below by title. Other tests may be performed by agreement between the supplier and thepurchaser.S1. Vacuum Treatment,S2. Product Analy

24、sis,S3. Simulated Post-Weld Heat Treatment of MechanicalTest Coupons,S4.2 Additional Tension Test,S5. Charpy V-Notch Impact Test,S6. Drop Weight Test (for Material 0.625 in. 16 mm andover in Thickness),S7. High-Temperature Tension Test,S8. Ultrasonic Examination in accordance with Specifica-tion A43

25、5/A435M,S9. Magnetic Particle Examination,TABLE 1 Chemical RequirementsNOTE 1Where “.” appears there is no requirement.Composition, %Type A Type B Type C Type D Type ECarbon, maxAManganese:B0.25 0.25 0.25 0.25 0.20Heat analysisProduct analysis1.151.501.071.621.151.501.071.621.151.501.071.621.151.501

26、.071.621.151.701.041.84Phosphorus, maxASulfur, maxASilicon:0.0250.0250.0250.0250.0250.0250.0250.0250.0200.015Heat analysisProduct analysisMolybdenum:0.150.400.130.450.150.400.130.450.150.400.130.450.150.400.130.450.150.400.130.45Heat analysisProduct analysisNickel:0.450.600.410.640.450.600.410.640.4

27、50.600.410.640.450.600.410.640.250.600.210.64Heat analysisProduct analysis.0.400.700.370.730.701.000.671.030.200.400.170.430.601.000.571.03Chromium, max:Heat analysisProduct analysis.0.600.64AApplies to both heat and product analyses.BFor Types A, B, C, and D, the maximum manganese content may be in

28、creasedto 1.60 % on heat analysis and 1.65 % on product analysis when Class 2 or Class3 properties are specified and when Supplementary Requirement S3 (seeSpecification A20/A20M) is specified with a total holding time of more than 1 h/in.2.4 min/mm of thickness.TABLE 2 Tensile RequirementsClass 1 Cl

29、ass 2 Class 3ksi MPa ksi MPa ksi MPaTensile strengthYield strength, min80100 55069050 34590115 62079570 485100125 69086083 570Elongation in 2 in.50 mm, min, %A18 16 16ASee Specification A20/A20M for elongation adjustment.A533/A533M 162S11. Ultrasonic Examination in accordance with Specifica-tion A57

30、7/A577M,S12. Ultrasonic Examination in accordance with Specifica-tion A578/A578M,S17. Vacuum Carbon-Deoxidized Steel, andS19. Restricted Chemical Requirements.ADDITIONAL SUPPLEMENTARY REQUIREMENTSAlso listed below is additional optional Supplementary Requirements S53, which is suitable for thisspeci

31、fication.S53.S53.1 When specified by the purchaser, the axis of thetensile and impact test specimens shall come from the mid-thickness of each plate tested, in lieu of midway between thecenter thickness and the top or bottom surface of the plate.APPENDIX(Nonmandatory Information)X1. NUCLEAR REACTOR

32、BELTLINE CONSIDERATIONSRESIDUAL ELEMENTSX1.1 Reactor design requires review and control of residualelements that affect the material properties. Copper and phos-phorus are limited to levels determined by the total fluence tobe encountered during plant life. Vanadium and sulfur canaffect the upper en

33、ergy shelf level. In the case of sulfur, controlof this element or its morphology in the plate, or both, mayoffer alternative means of control. The limits required shall bespecified in the ordering data. The following table itemizescurrently available commercial limits for the referenced ele-ments:E

34、lement Heat Analysis, % Product Analysis, %Copper 0.10 0.12Phosphorus 0.012 0.015Sulfur 0.010 0.013Vanadium 0.03 0.04SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue(A533/A533M 09 (2014) that may impact the use of this standard. (A

35、pproved May 1, 2016.)(1) Revised 1.3.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the ri

36、skof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of th

37、is standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake

38、 your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by

39、 contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 163