ASSE 1066-1997 Performance Requirements for Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings《个人固定接头同轴管压力平执行要求衡》.pdf
《ASSE 1066-1997 Performance Requirements for Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings《个人固定接头同轴管压力平执行要求衡》.pdf》由会员分享,可在线阅读,更多相关《ASSE 1066-1997 Performance Requirements for Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings《个人固定接头同轴管压力平执行要求衡》.pdf(23页珍藏版)》请在麦多课文档分享上搜索。
1、Performance Requirements forIndividual PressureBalancing In-LineValves for IndividualFixture FittingsAmerican Society of Sanitary EngineeringASSE Standard #1066-1997ASSE Board Approved: September 2, 1997General InformationNeither this standard, nor any portion thereof, may be reproduced without the
2、writtenconsent of the American Society of Sanitary Engineering.No product may be said to be ASSE approved unless the manufacturer has applied to theASSE, has had the product tested by an official ASSE recognized independent laboratory,according to the applicable ASSE Standard, passed the test, and h
3、as been reviewed andapproved by the consensus ASSE Seal Control Board. Having completed the aforementioned,the manufacturer may then display the ASSE Seal on the product.Instructions for receiving the authorization to display the Seal are available from ASSECentral Office. Organizations wishing to a
4、dopt or list any ASSE Standard should print the ASSEStandard Number on the cover page first and in equal or larger type to that of the adopting orlisting organization.American Society of Sanitary EngineeringWestlake, OhioCopyright 1997All rights reserved.Individual Pressure Balancing Valves for Indi
5、vidual Fixture Fittings iii Individual Pressure Balancing Valves for Individual Fixture FittingsASSE #1066 Issued: 1997ForewordThis Foreword shall not be considered a part of the standard; however it is offered to providebackground information.ASSE Standards are developed in the interest of consumer
6、 safety.Personal safety has prompted the initiation of this standard by forming a joint American Soci-ety of Sanitary Engineering (ASSE) and Plumbing Manufacturers Institute (PMI) working groupon April 4, 1993.Recognition is made of the time volunteered by members of the working groups and of thesup
7、port of the manufacturers who also participated in the meetings for this standard.The standard does not imply ASSEs endorsement of a product which conforms to theserequirements. Compliance with this standard does not imply acceptance by any code body,unless the standard has been adopted by the code.
8、This standard was promulgated in accordance with procedures developed by the AmericanNational Standards Institute (ANSI).Individual Pressure Balancing Valves for Individual Fixture Fittings iiiASSE #1066 Issued: 19971996-97 ASSE Standards CommitteeRichard J. ProspalStandards Committee ChairmanRelian
9、ce Mechanical, Cleveland, OhioRand AckroydWatts Regulator Company, North Andover, MassachusettsMichael BeckwithState of Wisconsin DILHR, Madison, WisconsinSidney L. CavanaughCalifornia State Pipe Trades, Los Angeles, CaliforniaA. Richard EmmersonChicago Faucet Company, Des Plaines, IllinoisDale Holl
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASSE10661997PERFORMANCEREQUIREMENTSFORINDIVIDUALPRESSUREBALANCINGINLINEVALVESFORINDIVIDUALFIXTUREFITTINGS
链接地址:http://www.mydoc123.com/p-457125.html