ASD-STAN PREN 4165-025-2015 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 025 Module receptacle Product standard (Edition P 2.pdf

《ASD-STAN PREN 4165-025-2015 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 025 Module receptacle Product standard (Edition P 2.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4165-025-2015 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 025 Module receptacle Product standard (Edition P 2.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4165-025 Edition P 2 April 2015 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: 49.060 Supersedes edition P

2、1 of May 2010 and will supersede EN 4165-025:2011 Descriptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 025: Module receptacle Product standard Srie arospatiale Connecteurs lectriques rectangulaires, modulaires Tempratu

3、re dutilisation 175 C continu Partie 025 : Embase mono-module Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 025: Fester Steckverbinder fr Einzelmodul Produktnorm This “Aerospace Series“ Prestandard has been drawn

4、 up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to

5、the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a d

6、raft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national

7、 standards conflicting with the EN. Edition approved for publication 1st April 2015 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2015 by ASD-STAN prEN 4165-025:2015 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3

8、Terms and definitions .3 4 Required characteristics .3 5 Designation . 24 6 Marking 25 7 Technical specification 25 8 Mounting example 26 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with t

9、he rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4165-025:2015 (E) 3 1 Scope This standard defines the single module receptacle used in the family of rectangular electrical connectors. The plug corresponding to this receptacl

10、e is defined in EN 4165-024. Accessories and protective cover corresponding to those plugs are defined in EN 4165-026. The cavity of this connector is uncoded, so it can accept polarized modules N, A, B, C and D as defined in EN 4165-002. 2 Normative references The following documents, in whole or i

11、n part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospac

12、e products EN 4165-001, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification EN 4165-002, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002: Specification of

13、performance and contact arrangements EN 4165-018, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 018: Protective cover for all receptacles series 2 Product standard EN 4165-024, Aerospace series Connectors, electrical, rectangular, modular O

14、perating temperature 175 C continuous Part 024: Single module plug Product standard EN 4165-026, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 026: Accessories for single module connector Product standard 3 Terms and definitions For the pur

15、poses of this document, the terms and definitions given in EN 4165-001 apply. 4 Required characteristics 4.1 Single module flange receptacle design (short receptacle) Type 0 Dimensions, alternative design and positions of keying polarization see Clause 5. See Figures 1, 2, 3 and 4. Dimensions are in

16、 millimetres. Mass = 6 g max. prEN 4165-025:2015 (E) 4 Figure 1 With alternatives designs prEN 4165-025:2015 (E) 5 Detail A Figure 2 With alternatives designs prEN 4165-025:2015 (E) 6 Figure 3 With alternatives designs prEN 4165-025:2015 (E) 7 Figure 4 With alternatives designs prEN 4165-025:2015 (E

17、) 8 4.2 Single module jack receptacle (extender) design (long receptacle) Type 7 Dimensions and positions of keying polarizations see Clause 5. See Figures 5, 6, 7, 8 and 9. Dimensions are in millimetres. Mass 7,5 g max. Figure 5 With alternatives designs prEN 4165-025:2015 (E) 9 Figure 6 With alter

18、natives designs prEN 4165-025:2015 (E) 10 Detail A Figure 7 With alternatives designs prEN 4165-025:2015 (E) 11 Figure 8 With alternatives designs prEN 4165-025:2015 (E) 12 Key 1 Orientation module 2 Index for rear accessory Figure 9 With alternatives designs prEN 4165-025:2015 (E) 13 4.3 Single mod

19、ule extender rear accessory attachment design for Type 7 only Dimensions and positions of keying polarizations see Clause 5. See Figures 10, 11 and 12. Dimensions are in millimetres. Figure 10 With alternatives designs prEN 4165-025:2015 (E) 14 Key 1 Cavity 2 2 on flats Figure 11 With alternatives d

20、esigns prEN 4165-025:2015 (E) 15 Figure 12 With alternatives designs 4.4 Class See Table 1. Table 1 Class Description M Receptacle with housing (shell) nickel plated, composite material, 500 h resistance to salt mist, maximum operating temperature 175 C continuous prEN 4165-025:2015 (E) 16 4.5 Panel

21、 cut out See Figures 13, 14, 15, 16, 17, 18, 19 and 20. Free cut out is all receptacles whatever polarization, see Figure 14. Orientation cut out is for all receptacles whatever polarization but provide 180 orientation, see Figure 15. Other Figure 16 to Figure 20 provides polarized panel cut out. Di

22、mensions are in millimetres. Figure 13 Panel cut out general dimensions Figure 14 Free mounting cut out dimensions Figure 15 Oriented panel cut out dimensions prEN 4165-025:2015 (E) 17 Polarization N Polarization A Figure 16 Detail keying dimensions for N and A panel cut out Polarization B Polarizat

23、ion C Figure 17 Detail keying dimensions for B and C panel cut out prEN 4165-025:2015 (E) 18 Polarization D Polarization E Figure 18 Detail keying dimensions for D and E panel cut out Polarization F Polarization G Figure 19 Detail keying dimensions for F and G panel cut out prEN 4165-025:2015 (E) 19

24、 Polarization H Figure 20 Detail keying dimensions for H panel cut out 4.6 Additional parts 4.6.1 Colour coding plate (Type code C) Colour according to polarization, see 5.2. See Figures 21, 22, 23, 24, 25 and 26. Dimensions are in millimetres. Mass 1,2 g max. Key 1 Four holes 2,93,1Figure 21 Panel

25、cut out general dimensions prEN 4165-025:2015 (E) 20 Polarization N Polarization A Figure 22 Detail keying dimensions for N and A colour coding plate Polarization B Polarization C Figure 23 Detail keying dimensions for B and C colour coding plate prEN 4165-025:2015 (E) 21 Polarization D Polarization

26、 E Figure 24 Detail keying dimensions for D and E colour coding plate Polarization F Polarization G Figure 25 Detail keying dimensions for F and G colour coding plate prEN 4165-025:2015 (E) 22 Polarization H Figure 26 Detail keying dimensions for H colour coding plate 4.6.2 Nut plate (Type code D) S

27、ee Figure 27. Dimensions are in millimetres. Material: Stainless steel. Mass 1 g max. Key 1 Four threads for screw 4-40 UNC-2A Figure 27 prEN 4165-025:2015 (E) 23 4.6.3 Sealing gasket (Type code E) See Figure 28. Dimensions are in millimetres. Material: Silicone elastomer. Mass 0,8 g max. Figure 28

28、prEN 4165-025:2015 (E) 24 5 Designation 5.1 Designation of receptacle EXAMPLE Description block ELECTRICAL CONNECTOR RECEPTACLE Identity block EN4165 M 7 1 A N Not marked on product 0 G 0 Number of the basic standard Classes type, see 4.4 M composite nickel plated Shell type, see EN 4165-002 0: shor

29、t receptacle (see EN 4165-002) 7: extender receptacle Shells type 1 Mono module Type A Module type series 2 (see EN 4165-002) Polarization code Code Colour N Black A Red B Blue C Green D Yellow E Pink F Clear green G Clear grey H Light olive Keying colour coding plate 0 Not included 1 Included Seali

30、ng gasket U Without sealing gasket G Delivered with sealing gasket Nut plate 0 Without nut plate 1 Delivered with integrated rear nut plate Receptacle may be delivered with or without keying colour coding plate, sealing gasket, and nut plate. The full reference containing last three digits is only m

31、arked on packaging. prEN 4165-025:2015 (E) 25 5.2 Designation of colour coding plate EXAMPLE Description block COLOUR CODING PLATE Identity block EN4165-25 C N Number of the basic standard Type code C colour plate (see Figures 21 to 26) Polarization code Code Colour N Black A Red B Blue C Green D Ye

32、llow E Pink F Clear green G Clear grey H Light olive 5.3 Designation of nut plate EXAMPLE Description block NUT PLATE Identity block EN4165-25 D Type code D (see Figure 27) 5.4 Designation of sealing gasket EXAMPLE Description block SEALING GASKET Identity block EN4165-25 E Type code E (see Figure 2

33、8) 6 Marking Unless there are other specific contractual requirements, the marking shall be in accordance with EN 2424, category P. 7 Technical specification See EN 4165-001. prEN 4165-025:2015 (E) 26 8 Mounting example See Figure 29. Key 1 Receptacle 2 Colour coding plate (option) 3 Sealing gasket 4 Nut plate (option) 5 Screw (not delivered) 6 Panel (up to 2 mm thick.) Figure 29