ARMY UFGS-22 33 30 00 10-2008 SOLAR WATER HEATING EQUIPMENT《太阳能热水器设备》.pdf

《ARMY UFGS-22 33 30 00 10-2008 SOLAR WATER HEATING EQUIPMENT《太阳能热水器设备》.pdf》由会员分享，可在线阅读，更多相关《ARMY UFGS-22 33 30 00 10-2008 SOLAR WATER HEATING EQUIPMENT《太阳能热水器设备》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-22 33 30.00 10 (April 2008)-Preparing Activity: USACE SupersedingUFGS-22 33 30.00 10 (January 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated March 2008*SECTION TABLE OF CONTENTSDIVISION 22 - PLUMBINGSECTION 22 33 30.00 10S

2、OLAR WATER HEATING EQUIPMENT04/08PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.3 SUBMITTALS1.4 WELDER QUALIFICATIONS1.5 DELIVERY, STORAGE, AND HANDLING1.6 WARRANTY1.7 SPARE PARTSPART 2 PRODUCTS2.1 GENERAL EQUIPMENT REQUIREMENTS2.1.1 Standard Products2.1.2 Nameplates2.1.3 Identical Items2.1.4 E

3、quipment Guards and Access2.1.5 Special Tools2.2 PIPING SYSTEM2.2.1 Copper Tubing2.2.2 Solder2.2.3 Joints and Fittings for Copper Tubing2.2.4 Flanges2.2.5 Dielectric Waterways and Flanges2.2.6 Bronze Gate, Globe, Angle, and Check Valves2.2.7 Ball Valves2.2.8 Relief Valves, Pressure and Temperature2.

4、2.9 Calibrating Balancing Valves2.2.10 Air Vents2.2.11 Strainers2.2.12 Pressure Gauges2.2.13 Thermometers2.2.14 Pipe Threads2.2.15 Pipe Supports2.2.16 Aluminum Sheets2.2.17 Copper Sheets Copper Alloy 110SECTION 22 33 30.00 10 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted

5、 without license from IHS-,-,-2.3 ELECTRICAL WORK2.4 COLLECTOR SUBSYSTEM2.4.1 Solar Collector Construction2.4.2 Absorber Plate and Flow Tubes2.4.3 Cover Glazing2.4.4 Insulation2.4.5 Casing2.4.6 Mounting and Assembly Hardware2.4.7 Solar Collector Performance2.5 Solar Collector Array2.5.1 Net Absorber

6、 Area and Array Layout2.5.2 Piping2.5.3 Supports for Solar Collector Array2.6 STORAGE TANK2.7 TRANSPORT SUBSYSTEM2.7.1 Heat Exchanger2.7.1.1 Plate Heat Exchanger2.7.1.2 Tube-in-Shell Heat Exchanger2.7.2 Pumps2.7.3 Pipe Insulation2.7.4 Expansion Tank2.7.5 Heat Transfer Fluid2.8 CONTROL AND INSTRUMENT

7、ATION SUBSYSTEM2.8.1 Differential Temperature Control Equipment2.8.2 Thermistor Temperature Sensors2.8.3 Sensor and Control Wiring2.8.4 Flowmeters2.8.5 Sight Flow Indicators2.9 PAINTING AND FINISHINGPART 3 EXECUTION3.1 EXAMINATION3.2 INSTALLATION3.2.1 Collector Subsystem3.2.1.1 Collector Array3.2.1.

8、2 Array Piping3.2.1.3 Array Support3.2.2 Storage Subsystem3.2.3 Transport Subsystem3.2.3.1 Flow Rates3.2.3.2 Pumps3.2.3.3 Expansion Tank3.2.3.4 Piping, Valves, and Accessories3.2.3.5 Pipe Expansion3.2.3.6 Valves3.2.3.7 Foundations3.2.3.8 Grooved Mechanical Joints3.2.4 Control Subsystem3.2.4.1 Differ

9、ential Temperature Controller3.2.4.2 Sequence of Operation3.3 INSPECTION AND TESTING3.3.1 Inspection3.3.2 Testing Prior to Concealment3.3.2.1 Hydrostatic Test3.3.2.2 Cleaning of Piping3.3.3 Posting Framed Instructions3.3.4 Acceptance Testing and Final Inspection3.3.4.1 As-Built DrawingsSECTION 22 33

10、 30.00 10 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.4.2 Final Hydrostatic Test3.3.4.3 System Flushing3.3.4.4 System Filling3.3.4.5 Operational Test3.3.4.6 Control Logic3.3.4.7 Temperature Sensor Diagnostics3.3.4.8 Overall System Opera

11、tions3.4 FIELD TRAINING- End of Section Table of Contents -SECTION 22 33 30.00 10 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-22 33 30.00 10 (April 2008)-Preparing Activity: USACE SupersedingUFGS-22 33 3

12、0.00 10 (January 2008)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated March 2008*SECTION 22 33 30.00 10SOLAR WATER HEATING EQUIPMENT04/08*NOTE: This guide specification covers the requirements for solar domestic and service water heating equipment.Edit this guide s

13、pecification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments and suggestions

14、 on this guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change

15、 Request (CCR).*PART 1 GENERAL*NOTE: In accordance with the design guidance presented in UFC 3-440-01, the system is designed around the properties of a particular collector. The designer should indicate the design methodology used on the drawings. This ensures that equipment shown on detail drawing

16、s (if different from the equipment assumed by the designer) is properly sized. It is particularly important for the designer to indicate on the drawings the collector parameters used in the design. Detail drawings returned should also be so noted, particularly if the collector chosen has properties

17、different from those used in the original design. UFC 3-440-01 provides the designer, project manager, and quality SECTION 22 33 30.00 10 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-assurance personnel a checklist of required drawings and i

18、nformation called out by this guide specification to appear on the drawings.*1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organ

19、ization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.Referen

20、ces not used in the text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to withi

21、n the text by the basic designation only.AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING ENGINEERS (ASHRAE)ASHRAE 93 (2003; Errata 2003) Methods of Testing to Determine the Thermal Performance of Solar CollectorsAMERICAN WATER WORKS ASSOCIATION (AWWA)AWWA C606 (2006) Grooved and Shou

22、ldered JointsAMERICAN WELDING SOCIETY (AWS)AWS B2.1 (2005; Errata 2006; Errata 2006) Welding Procedure and Performance QualificationAWS D1.2/D1.2M (2003; Errata 2004) Structural Welding Code - AluminumASME INTERNATIONAL (ASME)ASME B1.20.1 (1983; R 2006) Pipe Threads, General Purpose (Inch)ASME B16.1

23、5 (2006) Cast Bronze Threaded Fittings Classes 125 and 250SECTION 22 33 30.00 10 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B16.18 (2001; R 2005) Cast Copper Alloy Solder Joint Pressure FittingsASME B16.22 (2001; R 2005) Standard for

24、Wrought Copper and Copper Alloy Solder Joint Pressure FittingsASME B16.24 (2006) Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 400, 600, 900, 1500, and 2500ASME B16.26 (2006) Standard for Cast Copper Alloy Fittings for Flared Copper TubesASME B16.39 (1998; R 2006) Standard f

25、or Malleable Iron Threaded Pipe Unions; Classes 150, 250, and 300ASME B31.1 (2007) Power PipingASME B40.100 (2006) Pressure Gauges and Gauge AttachmentsASME BPVC SEC VIII D1 (2007) Boiler and Pressure Vessel Code; Section VIII, Pressure Vessels Division 1 - Basic CoverageASME PTC 19.3 (1974; R 2004)

26、 Temperature Measurement Instruments and ApparatusASTM INTERNATIONAL (ASTM)ASTM A 183 (2003) Standard Specification for Carbon Steel Track Bolts and NutsASTM A 536 (1984; R 2004) Standard Specification for Ductile Iron CastingsASTM B 152/B 152M (2006a) Standard Specification for Copper Sheet, Strip,

27、 Plate, and Rolled BarASTM B 209 (2007) Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B 209M (2007) Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)ASTM B 32 (2004) Standard Specification for Solder MetalASTM B 62 (2002) Standard Specificat

28、ion for Composition Bronze or Ounce Metal CastingsASTM B 75 (2002) Standard Specification for Seamless Copper TubeASTM B 75M (1999; R 2005) Standard Specification for Seamless Copper Tube (Metric)SECTION 22 33 30.00 10 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted withou

29、t license from IHS-,-,-ASTM B 828 (2002) Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and FittingsASTM B 88 (2003) Standard Specification for Seamless Copper Water TubeASTM B 88M (2005) Standard Specification for Seamless Copper Water Tube (Metric)ASTM C

30、 1048 (2004) Standard Specification for Heat-Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated GlassASTM D 2000 (2006ae1) Standard Classification System for Rubber Products in Automotive ApplicationsASTM F 1199 (1988; R 2004) Cast (All Temperatures and Pressures) and Welded Pipe Line Straine

31、rs (150 psig and 150 degrees F Maximum)CSA AMERICA, INC. (CSA/AM)CSA/AM Z21.22 (1999; R 2004; A 2000, 2001; R 2004) Relief Valves for Hot Water Supply SystemsMANUFACTURERS STANDARDIZATION SOCIETY OF THE VALVE AND FITTINGS INDUSTRY (MSS)MSS SP-110 (1996) Ball Valves Threaded, Socket-Welding, Solder J

32、oint, Grooved and Flared EndsMSS SP-58 (2002) Standard for Pipe Hangers and Supports - Materials, Design and ManufactureMSS SP-69 (2003; R 2004) Standard for Pipe Hangers and Supports - Selection and ApplicationMSS SP-72 (1999) Standard for Ball Valves with Flanged or Butt-Welding Ends for General S

33、erviceMSS SP-80 (2003) Bronze Gate, Globe, Angle and Check ValvesNATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)NEMA MG 1 (2007) Standard for Motors and Generators1.2 SYSTEM DESCRIPTION*NOTE: For systems located in an area subject to freezing, the closed-loop antifreeze system is to be used. Th

34、is system requires the propylene-glycol based heat transfer fluid, two pumps, a heat SECTION 22 33 30.00 10 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-exchanger, and an expansion tank. For systems at locations in which freezing temperature

35、s do not occur, the direct circulation system may be used. UFC 3-440-01 provides further information on these system types and their appropriate uses.*Peovide a solar energy system arranged for preheating of service (domestic and/or process) water using flat plate liquid solar collectors. Include in

36、 the system components a solar collector array, storage tank, pumps, automatic controls, instrumentation, interconnecting piping and fittings, uninhibited food-grade propylene-glycol and water heat transfer fluid in a closed loop, potable water heat transfer fluid in an open loop, heat exchanger, ex

37、pansion tank, and accessories required for the operation of the system.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the min

38、imum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality C

39、ontrol system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving

40、authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following t

41、he “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ design

42、ation are for Contractor Quality Control approval. information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. The following shall be submitted in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SECTION 22 33

43、 30.00 10 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SD-02 Shop DrawingsSolar Energy SystemAs-Built DrawingsDrawings containing a system schematic; a collector layout and roof plan noting reverse-return piping for the collector array; a sy

44、stem elevation; an equipment room layout; a schedule of operation and installation instructions; and a schedule of design information including collector height and width, recommended flow rate and pressure drop at that flow rate, and number of collectors to be grouped per bank. Include on the drawi

45、ngs complete wiring and schematic diagrams and any other details required to demonstrate that the system has been coordinated and will properly function as a unit. Drawings shall show proposed layout and anchorage of equipment and appurtenances, and equipment relationship to other parts of the work, including clearances for maintenance an