ARMY MIL-R-44354-1988 RUFF PARKA EXTENDED COLD WEATHER《极冷天气皮大衣绉领》.pdf

《ARMY MIL-R-44354-1988 RUFF PARKA EXTENDED COLD WEATHER《极冷天气皮大衣绉领》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-R-44354-1988 RUFF PARKA EXTENDED COLD WEATHER《极冷天气皮大衣绉领》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、I MIL-R-44354 4 m 0b 0403bL7 5 m MI L-R- 4435 4 27 September 1988 MILITARY SPECIFICATION RUFF, PARKA, EXTENDED COLD WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers .an attachable synthetic fur ruff

2、for use with the parka in the Extended Cold Weather Clothing System. 1.2 Classification. The ruff shall be one type in the following sizes: X-Small Sma 11 Medium X- La r g e 2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- catio

3、ns, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the

4、 solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick MA 01760-5014 by using the self-addressed Standardization Do

5、eument Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS g7 PAGES; Provided by IHSNot for ResaleNo reproduction or networking permitted wit

6、hout license from IHS-,-,- _. ._ MIL-R-44354 4 777770b 0403620 L I 3 MIL-R-44354 SPECIFICATIONS FEDERAL V-T-285 - Thread, Polyester DDD-L-20 - Label: For Clothing, Equipage, and Tentage PPP-B-636 - Boxes, Shipping, Fiberboard (General Use) MIL I TARY MIL-F-10884 - MIL-F-21840 - MIL-L-35078 - MIL-C-4

7、3824 - MIL-C-44187 - STANDARDS FEDERAL FED-STD-751 - Fasteners , Snap Fastener, Tapes, Hook and Loop, Synthetic Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment, Equipage,: General Specification For Cloth, Synthetic Fur, Knitted Cloth, Laminated, Water-Proof

8、 and Moisture-Vapor Permeable Stitches, Seams, and Stitching MILITARY MIL-STD-105 - Samp1,ing Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Copies

9、 of specifications, standards, and handbooks required by contractors in connection wi-th specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity,) 2.2 Other publications. The following documents form a part of this specifi- cation to

10、 the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation, Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issues of the nongover

11、nment documents which are current on the date of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-44 3 5 4 COLOR ASSOCIATION OF THE UNITED STATES, INC. Department of Defense Standard Shades (Copies may be obtained from the Co

12、lor Association of the United States, fnc., 343 Lexington Avenue, New York, NY 10016.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) 1 D 3951 - Standard Practice or Commercial Packaging (copies may beobtained from the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA

13、 19103,) (Nongovernment standards and other publications are normally available from the organization which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services. 2.3 Order of precedence. In the event of a conflict be

14、tween the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS a 3.1 Guide samples. Samp

15、les of the end item, when furnished, are solely for guidance and information to the contractor (see 6.3). document may appear in the sample in which case this document shall govern, Variations from the 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected t

16、o first article inspection (see 4.3, 6.2, and 6.4). 3.3 Material, 3.3.1 Cloth, laminated. The basic material for the ruff shall be cloth, laminated, water-proof and moisture-vapor permeable, conforming to MIL-C-44187. 3.3.2 Synthetic fur ruff strips. The synthetic fur for the ruff shall conform to M

17、IL-C-43824. 3.3.3 Fastener, tape, hook and loop. The nylon fastener tapes shall be 1 inch wide hook tape arid 2 inch wide hook and loop tapes, Olive Green 106 conforming to type II, class 1 of MIL-F-21840, 3.3.4 Snap fastener. The stud and post parts of the snap fastener shall be style 2A, finish 2,

18、 complete, conforming to MIL-F-10884. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- -. _I_. I _ _ _- MIL-R-44354 4 a 7777906 0403622 5 W t MI L-R-4435 4 3.3.5 Thread. The threadfor all seaming and stitching shall be polyester, size B, 2 or 3 ply

19、, shade S-1, C.A. 66022 conforming to type I, class 1, subclass B of V-T-285. 3.3.6 Wire. - The wire for the edge of the ruff shall be bright, 0.080 2 0.003 inch diameter copper wire, dead soft, and shall not crack or break down when tested as specified in 4.4.1.1. 3.3.7 Labels, Each ruff shall have

20、 a class 4 identification and size label and a class 3 instruction label conforming to type VI of DDD-L-20. The label color shall be Medium Green, C.A. 70034, 70130, or 70131 and shall show fastness to laundering. 3.3.7.1 Identification and size label, The identification and size label shall first s

21、tate tne size and then read “Ruff, Parka, Extended Cold Weather“. 3.3.7.2 Instruction label. The instruction label shall be as follows: Launder ruff by hand, shake out water and air dry; or machine laurider, using warm water (900 - 1100F) and mild powdered laundry detergent. Rinse thoroughly in clea

22、n warm water. NOTE: Do not use bleach or starch. Air dry. WARNING: Do not tumble dry. 3.3.7.3 Combination label, The size and identification label and the instruction label may be combined into one label, conforming to class 14 of DDD-L-20. The size and identification label shall be placed above the

23、 instruction label with a space of 1/2 inch minimum maintained between the labels. 3.4 Design. The ruff shall be camouflage pattern with a natural white synthetic fur strip, a wire stiffener, snap fastener studs for attaching to the parka, and hook and loop fastener tape closures. 3.5 Patterns. Stan

24、dard patterns) which provide an allowance of 5/8 inch will The Government patterns shall not be altered in be furnished by the Government, any way and are to be used only as a guide for cutting the contractors working patterns, The working patterns shall be identical to the Government patterns. 3.5.

25、1 Pattern parts. The pattern components for the ruff shall be cut from the material as specified and according to the number of parts listed in table I. TABLE I. List of pattern parts Mat er i a 1 Nomenclature Parts Cloth, synthetic fur Fur strip 1 Cloth, laminated Ruff 2 4 Provided by IHSNot for Re

26、saleNo reproduction or networking permitted without license from IHS-,-,-t . . l . MIL-R-44354 4 7777706 0403623 7 M MI L-R-44 35 4 3.6 Construction. Construction shall conform in all respects to the requirements specified in table II and herein. Figure 1 is furnished solely for e guidance and infor

27、mation. the document shall govern. Should variation from the document appear in figure 1 3.6.1 Stitches, seams, and stitching. All stitches, seams, and stitching shall conform to FED-STD-751. The seam type, stitching type, and stitches per inch shall be as specified in table II. Seam allowances shal

28、l be maintained with seams sewn so that no raw edges, run-Offs, pleats, puckers, or open seams occur. When two or more methods of seams or stitches are given for the same operation, any one may be used. 3.6.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched not less

29、than 1/2 inch except where ends are tuined under or caught in other seams or stitching. Ends of a continuous line of stitching shall over- lap not less than 1/2 inch. will be no loose stitching resulting in loose bobbin or top thread or excess- ively tight stitching resulting in puckering of the mat

30、erials sewn. The lock shall be embedded in the materials sewn. Thread tensions shall be maintained so that there 3.6.1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks, skipped stitches, run-Offs, or bobbin runouts occur during sewing, the s

31、titching shall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. i/ b. Except for prestitching, thread breaks or two or more consecutive skipped or run-off stitches noted during inspection of the item shall be repaired by overstitching. back of the defec

32、tive area, continue over the defective area, and continue a minimum of 1/2 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials, and restitching in the required manner. L/

33、 The stitching shall start a minimum of 1/2 inch in - i/ When making the above repairs, the ends of the stitching are not required to be backstitched. 3.7 Manufacturing operations requirements. The ruff shall be manufactured in accordance with operation requirements specified in table II. The contra

34、ctor is not required to follow the exact sequence of operations listed. The use of drill holes is prohibited except for marking locations of snap fasteners in which case drill holes shall be no larger than 1/16 inch diameter. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

35、hout license from IHS-,-,-MIL-R-44354 . m U k a a al a El a a $4 O g *d U o al w al a W O U 0 al rl a 8 : c2 hl w hl d d I I I 4 O O O I+ 4 d n n W W hl 4 a P I al id cn cn 03 cn cn cn d d d O O O m m m ai k 3 m G 0 O. uw m3 UCI a m al m a bo .rl rl a m al M n 2 a* ala G aal C aal C P n ala u0 mLI .

36、u al 5: .d O? Li um 3a O c so mu 3 au d m ad n a. al 3cm oao O aual wrl :zu m . * P lu E L O 2, -* ao Z- 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- SI N rl I O rl N I rl O 4 N rl I O 4 rl ar) I e I4 4 r) I e I4 rl I 4 O m 4 O m rl O m a 4 bo

37、c al rl a 0 -(d h 2 rl (d u VI n VI U O a VI n VI a (d al k Y; $5 u alal o .rl rlu rlN (d .rl VI al t% 2 0) Ela a (d =e NVI k kcCi al li w I- V 3 -2 I x W !- z 3 w v 3 W 4 3 d a m =! y h l- u O U O c k al a w VI 3 k al Y w O al a .rl 2 Y .rl al O U aou dala al3 kc0 3 alw wu n a U d O o - v . w VI 1

38、k s 3 LI VI a 1 u. VIVI . VI a 7 U VI U al m d . vl a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-4LJ35q 8LJ 99997Ob O403b2b 2 e MIL-R-44354 3.8 Finished measurements. The finished measurements for the ruff shall conform to table III. TABLE

39、 III. Finished measurements (in inches) X-Small Small Medium Large X-Large Tolerance +1 33-3/4 34-1/4 34-7/8 35-1/2 36 - NOTE: The finished measurement shall be taken with the ruff lying flat on a table, fur face down, and measuring from end to end along snap fastener edge. 3,9 Workmanship. The fini

40、shed ruff shall conform to the quality of product established by this document and the occurrence of defects shall not exceed the applicable acceptable quality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the , contract or purchase.order, t

41、he contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, u

42、nless otherwise disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items

43、 must meet all requirements of sections 3 and 5. The inspection set forth in this document shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the document shall not relieve the contractor of the responsibility of assurin

44、g that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective

45、 material. 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible for assuring that all specified dimensions have been met. examined on the end item, inspection shall be made at any point, or at all points in the

46、 manufacturing process necessary to assure compliance with all dimensional requirements. When dimensions cannot be 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-R-4435 4 4.1.3 Certificate of compliance. When certificates of compliance are su

47、b- mitted, the Government reserves the right to check test such items tri determine the validity of the certification. 4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.3). b. Quality conformance inspection (s

48、ee 4.4). 4.3 First article inspection, When a first article is required (see 3.2), it shall be examined for the defects specified in 4.4.2. The presence of any defect shall be cause for rejection of the first article. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspe

49、ction shall be in accordance with MIL-CTD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspectedin accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this document or applicable purchase document. 4.4.1.1 Component and material certification, Unless ot