ARMY MIL-PRF-49450 B-2000 BATTERY RECHARGEABLE NICKEL-CADMIUM VENTED AIRCRAFT《镍镉飞机接口接充电电池》.pdf

《ARMY MIL-PRF-49450 B-2000 BATTERY RECHARGEABLE NICKEL-CADMIUM VENTED AIRCRAFT《镍镉飞机接口接充电电池》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-PRF-49450 B-2000 BATTERY RECHARGEABLE NICKEL-CADMIUM VENTED AIRCRAFT《镍镉飞机接口接充电电池》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-PRF-49450B(CR) I 10 March 2000 SUPERSEDING 9 October 1997 MIL-PRF-49450A(CR) PERFORMANCE SPECIFICATION BATTERY, RECHARGEABLE, NICKEL-CADMIUM, VENTED, AIRCRAFT. This specification is approved for use by the USACECOM, Department of Army, and is available for use by all Departments and A

2、gencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for BB-7 16/A, BB-432B/A, BB- 476/A, BB-649NA and BB-664/A vented, rechargeable nickel cadmium aircraft batteries and cells and harnesses used therein. 2. APPLICABLE DOCUMENTS 2.1 Government Document

3、s. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the Department of Defense Index of Specifications and S

4、tandards (DoDISS) and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, U.S. Army Communications-Electronics Command, ATTN: AMSEL-LC-LEO-E

5、-EP, Fort Monmouth, NJ 07703 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 6140 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Copyright Communications - Electronics Comman

6、d Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS FEDERAL FED-STD-595, Colors Used in Government Procurements DEPARTMENT OF DEFENSE MIL-STD-8 1 O Environmental Test Methods and Engineering Guidelines (Copies of speci

7、fications, standards, handbooks, drawings, and publications required by manufacturers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer). 2.2 Non-Government publications. The following document form a part of

8、this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the docume

9、nts cited in the solicitation (see 6.2). UL-1642 UL Standard for Safety Lithium Batteries (Applications for copies should be addressed to Underwriters Laboratories, Inc., 333 Pfiigsten Road, Northbrook, IL 60062.) 2.3 Order of precedence. In the event of a conflict between the text of this document

10、and the references cited herein (except for related associated specifications sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. Th

11、e individual item requirements shall be as specified herein and in accordance with the applicable specification sheet. In the event of any conflict between the requirements of this specification and applicable specification sheet, the latter shall govern. 3.2 First article. When specified (see 6.6),

12、 a sample shall be subjected to fikt article inspection, in accordance with 4.2. 3.3 Design, materials, and manufacturing. Unless otherwise specified, the design, materials, and manufacturing process selection is the prerogative of the contractor provided all articles submitted to the Government ful

13、ly meet the operating, interface, ownership and support, and operating environment requirements specified in this document. 2 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.1

14、 Metals. External metal or component parts of each battery, cell and harness shall show no evidence of cracking, chipping, scaling, corrosion or other deleterious effects when exposed to 1.300 k 0.025 specific gravity KOH electrolyte solution. 3.3.2 Plastic materials. Plastic materials used in each

15、battery, cell and harness shall show no evidences of cracks, blisters or other deterioration and shall not change more than 2.5 percent in weight or 2.0 percent in any dimension when exposed to 1.300 k 0.025 specific gravity KOH electrolyte solution. 3.3.3 Elastomer materials. All elastomer material

16、s used in each battery, cell and harness shall show no evidence of cracks, blisters or other deterioration after being exposed to 1.300 k 0.025 specific gravity KOH electrolyte solution. Materials of pads, gaskets and O-rings shall be selected to provide adequate seal and minimize compression set wh

17、en tested in accordance with 4.5.3. 3.4 Components. The battery, cells, and harness shall conform to this specification and specification sheets. 3.4.1 Batteries. 3.4.1.1 Battery container and cover. The battery container and cover shall be of alkali- resistant high strength material, free of rough

18、spots, pits, blowholes and other deformations. The container and/or cover shall be completely coated by an epoxy resin to a minimum thickness of 0.015 k .O08 inches to prevent absorption of electrolyte. The dimensions and location of receptacles hold-downs, latches, latch hooks, vent tubes, name and

19、 instruction plates, and carrying strap shall conform to the applicable specification sheets. The cover shall be fitted with a hold-down pad having an integral elastomer gasket positioned so as to match the rim of the container body for a gas-tight fit between the cover and the container body. The s

20、eal shall prevent the loss of pressure in excess of 2.75 inches of water when tested in accordance with 4.5.8. 3.4.1.2 Latches. The cover shall be secured to the container body by latches mounted on the container body, or by other means specified in the in the applicable specification sheet, and lat

21、ch hooks mounted on the cover. The latches and hooks shall be mounted on the cover and container body as specified in the applicable specification sheets (see 3.1). 3.4.1.3 Vents. The container body shall be provided with vents to permit gases liberated by the cells of the battery to be purged. Thes

22、e vents shall be located as shown in the applicable specification sheets (see 3.1). 3.4.1.4 Main power receptacle. The battery shall utilize a two-pin receptacle for a main power connector. The receptacle shall be mounted as shown in the applicable specification sheets. The receptacle shall be capab

23、le of withstanding a pull out force of 250 k 25 pounds and a torsional force of 6.0 k 0.5 foot-pounds. 3 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.1.5 Intercell connecto

24、rs. Intercell connectors shall comply with the applicable specification sheets. 3.4.2 Cells. The battery shall contain the number and type of cells in the configurations specified by the applicable specification sheets. 3.4.2.1 Cell mounting. The cells shall be removable but securely mounted in the

25、battery container such that they are not adversely affected by tests performed on the battery to determine its compliance with the requirements of this specification. 3.4.2.2 Cell container. The cell container shall be made of high strength, non-porous, alkali-resistant material. The surfaces of con

26、tainers shall have a smooth finish, free from pits, blowholes, rough spots, or other deformations. 3.4.2.3 Cell terminals. The size and spacing shall be as specified in the applicable specification sheets. Insulating compounds shall not obstruct the contact surfaces of the terminal. 3.4.2.4 Internal

27、 pressure. Each cell shall be assembled and constructed in such a manner that it shall be capable of withstanding an internal pressure of 20 +1 psig for 15 seconds. 3.4.2.5 Cell vents. Each cell shall be equipped with a vent per applicable specification sheet. The vent plug, when installed to the ce

28、ll at a torque of 3.5 + 1 .O in-lb., shall form an airtight seal for the cell when the cell internal pressure is below 2 psig. The vent plug shall be capable of providing automatic relief when the internal cell pressure reaches 6 + 4 psig. The vent plug shall withstand 7 in-lb of torque with no dama

29、ge. 3.4.2.6 Potassium carbonate. Cells from the battery shall be tested for potassium carbonate content in the electrolyte. The electrolyte shall not contain more than 60 grams per liter of carbonate. 3.4.3 Harness assembly. The harness assembly shall be capable of Withstanding the temperature and e

30、xposure of the battery electrolyte without damage (see 6.4). 3.4.3.1 Insulated wires. The harness assembly shall use insulated wires resistant to the battery electrolyte. The insulation shall be free from splinters, blisters and other non- homogeneities visible to the normal eye. 3.4.3.2 Electrical

31、connections. All electrical connections made to receptacle and harness devices (thermistors, thermoswitches ect.) shall be potted with a compound that will not support flame, absorb moisture, or be damaged by battery electrolyte. Contacts shall be so designed that neither the pins nor the sockets wi

32、ll be damaged during mating of counterpart connectors. 3.4.3.3 Thermistors. The harness assembly shall utilize temperature sensor devices that exhibit the resistance-temperature characteristics specified in applicable specification sheet. Potting employed to isolate the thermal sensors from any batt

33、ery voltage shall conform to 3.6.6. 4 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.3.4 Sensor receptacle. The battery shall use a hermetic jam nut receptacle to provide con

34、nection to battery sensing and control points. The location of the receptacle shall conform to applicable specification sheets (see 3.1). 3.4.3.5 Thermoswitches. Shall conform to the requirements of applicable specification sheet. 3.4.3.6 Device mounting. The devices (thermoswitches and thermistors)

35、 shall be mounted on a custom or standard connector strap in such a manner that it shall not become detached during handling. The devices shall be positioned on the connector in such a manner that they shall not interfere with the tool operations required for removal and mounting of cell. If the mou

36、nting scheme does not require a connector strap, a separate connector strap shall be provided for each device that is not mounted on a connector. 3.4.3.7 Insulation. All current carrying parts of the harness assembly shall be insulated from the metal parts of the sensor receptacle except for the app

37、licable pins. The insulation resistance between any current carrying part and the sensor receptacle (excluding the applicable pins) shall be above one megohm. 3.4.4 Dissimilar metals. Unless suitably protected against electrolytic corrosion, dissimilar metals shall not be employed in intimate contac

38、t with each other. This specification terms metals dissimilar when two metal specimens are in contact or otherwise electrically connected to each other in a conductive solution and generate an electric current. 3.4.5 Corrosion prevention. After the battery has been assembled, all exposed metal surfa

39、ces of the cells, intercell connectors and associated hardware, and harness shall be coated with a corrosion-preventive compound. The compound shall be uniform, free from grit, abrasives, water, chlorides, or other impurities. The manufacturer is responsible for maintaining carcinogenic free materia

40、ls. The compound shall be transparent during the protective life of the coating. The compound shall flow, be stable, and uniform. The compound shall contain no precipitates formation or permanent haziness in the solution. The compound shall not show evidence of pitting, etching, or darkening. Care s

41、hall be taken not to expose rubber vent sleeves, vent openings or current carrying surfaces to the corrosion preventive film. Coating shall be applied evenly and without voids. 3.4.6 Cleaning. All parts of the battery, cells and harness when assembled shall be cleaned. Corrosive material shall be re

42、moved completely. After assembly the battery, cells and harness shall be cleaned thoroughly and shall be free from particles of solder, flux and other foreign material. 3.4.7 Interchangeability. Parts and components of the batteries, cells and harness shall be functionally and dimensionally intercha

43、ngeable. 5 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4.8 Shipping condition of cells. All cells whether shipped in 19 cell packs or within the batteries shall be delivered

44、 complete with electrolyte to proper level and completely discharged, but fully formed. During shipment, a shorting plug or spring shall be connected to the batterys main power receptacle or to the cells terminals (if shipped separately). 3.4.8.1 Cell electrolvte level. Each cell shall have the elec

45、trolyte level adjusted so that after a full charge and a 2 hour stand, the level shall be 1/8 to 1/4 inches above the baffle. 3.5 Color and marking. 3.5.1. Color. The batteries, cells and components shall conform to the requirements in the applicable specification sheets. 3.5.2 Marking. Each battery

46、 or cell shall have its identification marking as specified in the following paragraphs and the applicable specification sheets. All markings and identifications shall be permanent and shall be resistant to 1.300 k 0.025 specific gravity KOH electrolyte. environment shall be used. A unique serial nu

47、mber is required on each nomenclatured item. The numbers shall be consecutively assigned. Clear and legible lettering and a method of marking to withstand the operating 3.5.2.1 Cell Marking. 3.5.2.1.1 Cell terminal marking. Positive terminal markings shall be impressed or embossed with a (+). Negati

48、ve terminal markings shall be impressed or embossed with a (-). The polarity marking shall be as close as possible to the terminals on the cover of the cell. The positive half of the cell cover shall be permanently marked red. Minimum width of the red band shall be no less than 0.5 inch. 3.5.2.1.2 C

49、ell identification. Each cell shall have the following information printed in black, 1/8-inch lettering: Battery, Rechargeable (Cell) *(NSN). Part of BB-xxx/*(AH)/lHR *(CONTRACT NO.) “(MANUFACTURER PART NO.) *FILL IN THE APPLICABLE INFORMATION 6 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Example label: Battery, Rechargeable (Cell) Part of BB-xx