ARMY MIL-P-52384 A-1987 PATCHES SEALING TAPE AND VULCANIZING FLUID PNEUMATIC FLOAT AND BOAT REPAIR《充气浮筒和修船用液体硫化剂和胶粘带补丁》.pdf

《ARMY MIL-P-52384 A-1987 PATCHES SEALING TAPE AND VULCANIZING FLUID PNEUMATIC FLOAT AND BOAT REPAIR《充气浮筒和修船用液体硫化剂和胶粘带补丁》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-52384 A-1987 PATCHES SEALING TAPE AND VULCANIZING FLUID PNEUMATIC FLOAT AND BOAT REPAIR《充气浮筒和修船用液体硫化剂和胶粘带补丁》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-P-52384A 54 797970b 0223423 T w MIL-P-52384A(ME) 28 May 1987 SUPERSEDING MIL-P-52384 (MO) 28 August 1964 MILITARY SPECIFICATION PATCHES, SEALING TAPE, AND VULCANIZING FLUID: PNEUMATIC FLOAT AND BOAT REPAIR . This specification is approved for use within the USA Belvoir Research, Development, and

2、 Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers repair material for pneumatic floats and boats. 1.2 Classification. The repair material shall be of the following types an

3、d classes, as specified (see 6.2): Type 1 - Patches Class 1 - Round Class 2 - Oblong Class 3 - Repair sheet Class 4 - Face gum sheet Type II - Sealing tape Type III - Vulcanizing fluid. 2. APPLICABLE DOCUMENTS 2.1 Government documents. Beneficial comments (recommendations, additions, deletions) and

4、any pertinent data which may be of use in improving this document should be addressed to: Belvoir Research, Development, and Engineering Center, ATTN: STRBE-TSE, Fort Belvoir, VA 22060-5606 by using the self-addressed Standardization Document . Improvement Proposal (DD Form 1426) appearing at the en

5、d of this document or by letter. . USA AMSC NIA FSC 5420 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. . F THIS DOCUMENT CONTAINS 7 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.1.1 Specifications, st-an

6、dards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent epecified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standar

7、ds (DODISSI and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-B-60 1 PPP-B-636 PPP-F-320 - Boxes, Wood, Cleated-Plywood. - Box, Fiberboard. - Fiberboard; Sheet, Stick and Cut Shapes. MILITARY MIL-C-14505 STANDARDS MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-130 - Cloth, Nylo

8、n, Polychloroprene-Coated (For Pneumatic Floating Equipment). - Sampling Procedures and Tables for - Marking for Shipment and Storage - Identification Marking of U.S. Military Inspection by Attributes. Property. (Copies of specifications, standards, handbooks, drawings, publications, and other Gover

9、nment documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited h

10、erein, (except for associated detail specifications, specifications sheets or MS standards), the text of this specification shall take precedence. shall supersede applicable laws and regulations unless a specific exemption has been obtained . Nothing in this specification, however, , 3 . REQUIREMENT

11、S I 3.1 Description. The repair material shall conform to MIL-C-14505 and be capable of making either hot or cold vulcanization repairs on pneumatic equipment and shall be as specified herein. 3.2 Identification marking, The repair material shall be identified in accordance with MIL-STD-130 with the

12、 following information: 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-5238LlA 54 9797906 0239425 3 a. Nomenclature. b. NSN C. Contract d. The notation “U.S.“ e. Manufacturers Identification. 3.3 Type I, patches. 3.3.1 Class 1, round. The ro

13、und patch shall be type 7, class C, 4-1/2 inch diameter, color black. 3.3.2 Class 2, oblong. The oblong patch shall be type 7, class C, 10 inch long diameter, 6 inch short diameter, color black. 3.3.3 Cl.ass 3, repair sheet. The repair sheet patch shall be type 7, class C, 10 feet Long, 24 inches wi

14、de, color black. 3.3.4 C1as.s 4,. face gum sheet. The gum sheet shall be made from coating compound specified in MIL-C-14505, and shall be approximately .O20 THK, 10 ft. long-and 24 inches wide, color black. 3.4 Type,II,Sealing tape. The sealing tape shall be type 7, class C, two 12-1/2 feet long, 2

15、-1/2 inch wide color black. 3.5 Type.111, vulcanizing fluid. The vulcanizing fluid shall be bostik - 2405 two part cement and bostikure D, or equal. 3.5.1 Self life marking. Each container of the vulcanizing fluid shall be marked with the shelf life expiration date (month and year). determined as th

16、e useful life that the supplier certifies for the vulcanizing fluid. Shelf life shall be 3.6 Buffing solution. The solvent shall be commercial quality suitable for wiping Gepair area in preparation for applying adhesive. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility .for inspection. Unless othe

17、rwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements

18、speci- fied herein, unless disapproved by the Government. right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in The Government reserves th

19、e 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RIL-P-5Z3YA 5Li m 9779906 02L9Li26 5 m 4.1,1 RS,p,ns,biliy for compl.iance. All items must meet all requirements of The inspection set forth in this specification shall become a sections 3 and 5. pa

20、rt of the contractors overall inspection system or quality program. absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of

21、the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material, The 4.2 Examination. Each repair material shall be examined for the following defects. Presence

22、of one or more defects shall be cause for rejection: 101. 102. 103. 104. Type and class of repair material not as specified. Identification marking incorrect, missing, or illegible. Shelf life marking for type III repair material missing or shelf life expiration date not valid, Buffing solution not

23、as specified, 4.3 Tnspec t.io.n. of. packaging. 4.3.1 Quality conformance inspection of packaging. 4.3.1.1 Unie of pr,oduct, For the purpose of inspection, a completed pack prepared for shipment shall be considered a unit of product. 4.3,1.2 Samplin. Sampling for examination shall be in accordance w

24、ith MIL-STD-105 o 4.3.1-3 Examination. Samples selected in accordance with 4.3.1.2 shall be examined for the following defects. 1.0 percent defective. The AQL (Acceptable Quality Level) shall be No. Defect Level A Level C 105. Unit containers for patches, 5.1.1.1 repair sheets and face gum sheets no

25、t as specified, tape not as specified. fluid not as specified, solution not as specified, with unlike items. as specified. utilized as specified. 106, Unit container for sealing 5.1.1.2 107. Unit container for vulcanizing 5.1.1.3 108. Unit container for buffing 5.1, 1.4 109. Intermediate containers

26、filled 5.1.2 110, Intermediate containers not 5.1.2.1 111. Partitions and pads not 5.1,2.1 5.1.1.1 5.1, 1.2 5.1.1.3 5.1.1.4 5.102 5.1.2.2 5.1.2.2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-52384A 5LI 777770b 0237427 7 W MIL-P-5 2384A( ME

27、) NO 112. 113. 114. 115. .I -3 116. 117. 118. 119. 120. Defect Level. A Level C Corrugated fiberboard 5.1.2.1 5.1.2.2 partitions and pads not material specified. Unlike items packed in 5.2.1 5.2.2 same shipping container when not specified. Shipping container not as 5.2.1 5.2.2 specified. Gross weig

28、ht of shipping 5.2.1 5.2.2 container exceeds maximum specified. Shipping container closure 5.2.1 5.2.2 and strapping not as specified. Unlike items not consolidated 5.2.3 5.2.3 together in the specified quantities, when required. Consolidation container, when 5.2.3 5.2.3 required, not as specified.

29、Gross weight of consolidation 5.2.3 5.2.3 container exceeds maximum specified. Marking not as specified. 5.3 5.3 5. PACKAGING 5.1 Preservation. Preservation shall be level A or level C as specified (see 6.2). 5.1.1 Unit .containers. Unit containers shall be furnished as follows 5.1.1.1 Patches. 5.1.

30、1.1.1 Type I,.class 1 (round 4,.50 inch diameter). Ten each 4.5 inch diameter patches shall be placed in a unit container utilizing the manufacturers normal type container. 5.1.1.1.2 Type I, class2 (oblong 10.00 inch X 6.00 inch diameter). Ten each oblong patches shall be placed in a unit container,

31、 utilizing the manufacturers normal type Container. 5.1.1.1.3 Type I, class 3 (repair sheet), Each repair sheet shall be folded or rolled, tightly secured and then placed in a unit container utilizing the manufacturers normal type container. 5.1.1.1.4 Type I, class 4 (face.,gum sheet). Each face gum

32、 sheet shall be folded or rolled, tightly secured and then placed in a unit container, utilizing the manufacturers normal type container. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-5Z384A 54 9997906 0234q28 i 5,1.1.2 Type II, (sealing ta

33、pe). Two rolls of sealing tape shall be plgced in a unit container, utilizing the manufacturers normal type container. 5.113 Type III.(vulcanizing fluid). The vulcanizing fluid shall be Eurniehed in metal screw cap cans, utilizing the manufacturers normal type container. applicator brush furnished w

34、ith each can. The can shall have a capacity of 8 to 8-1/2 fluid ounces with an 5.1.1.4 BuEfing sol-ution. The buffing solution shall be furnished in metal screw cap cans, utilizing the manufacturers normal type container. shall have a capacity of 6 fluid ounces, The can 5.1.2 Intermediate containers

35、. Items of like description, in unit containers as specified in 5.1.1, shall be placed in a close-fitting intermediate container. Unit containers of the vulcanizing fluid, and as applicable, the unit containers of the buffing solution, shall be separated from each other within the intermediate conta

36、iner by the use of partitions and pads of corrugated fiberboard. construction of the intermediate container shall be as follows. The gross weight of the container shall not exceed 30 pounds. The 5.1,2.1 Level A. The intermediate container shall be a corrugated fiberboard box conforming to PPP-B-636,

37、 grade W6c. the unit containers of vulcanizing fluid and buffing solution shall be in accordance with PPP-F-320, grade W6c. the appendix to the box specification. The partitions and pads for separating Box closure shall be in accordance with 5.1.2,2 Level C. The intermediate container and the partit

38、ions and pads shall be as speci2ied for level A in 5.1.2.1 except that the fiberboard shall be class domestic, variety SW, grade 175. 5,2 Packin&. Packing shall be level A or level C as specified (see 6.2). 5.2.1 Level p. Items of like description, in unit containers and intermediate containers as s

39、pecified in 5.1.1 and 5.1.2 respectively, shall be packed together in a close-fitting box conforming to PPP-B-601, overseas type, style optional. The gross weight of the box shall not exceed 200 pounds. Box closure and strapping shall be as specified in the box specification and the appendix thereto

40、, except that the strapping shall be flat and the finish B. 5.2.2 Level C. Items of like description in unit containers and intermediate containers as specified in 5.1.1 and 5.1.2 respectively, shall be packed as specified in 5,2,1 for level A except that the boxes shall be domestic type and the str

41、apping may be finish A. 5.2.3 Consol.idation. When specified (see 6.21, unlike items shall be packed together, shall be as specified (see 6.2). Each item shall be in unit containers and intermediate containers as specified in 5.1.1 and 5.1.2 respectively. consolidation container shall be a close-fit

42、ting box in accordance with the The quantity of each item to be packed in each consolidaton container The 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-P-52384A 54 9999906 021V29 O m applicable level A or level C requirement of 5.2.1 or 5.2

43、.2 as specified (see 6.2). maximum of 300 pounds provided all applicable requirements of PPP-B-601 are satisfied. The gross weight of the consolidation container may be increased to a 5.3 Marking. In addition to any special or identification markings required by the contract or purchase order and as

44、 specified in 3.2, each unit container, intermediate container and shippinglexterior container shall be marked in accordance with MIL-STD-129. 6. NOTES 6.1 Intended use. The repair material is intended for use in making air leakage repairs on pneumatic floats and boats fabricated from neprene- coate

45、d nylon cloth. 6.2 Ordering data. Procurement documents should specify the following: a. Title, number, and date of this specification. b. Type and class required (see 1.2). c. Level of preservation and level of packing required (see 5.1 and 5.2 respectively). d. When consolidation of unlike items t

46、ogether is required (see 5.2.3). e. Quantities of unlike items to be packed together in consolidation container (see 5.2.3). f. Any special marking (see 5.3). 6.3 ages,ted manufac.tu.rers. Suggested manufacturers are as follows : Aldan Rubber Co. Tioga and Salmon St. Philidelphia, PA 19134 Reeves Br

47、oc. Inc. P.O. Box 153, Spartansburg, SC 29304 6.4 Subject term (key word) listing. Inflatable, pneumatic boats Neoprene Pneumatics Rubber coated fabric 6.5 Changes from previous issue. Asterisks (or vertical lines) are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. Custodian: Preparing activity: Army - ME 7 Army - ME Project 5420-A359 U.C. GOVERHIBII PINTIHG OFFICE: 1987 - 784-3U3561 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-