ARMY MIL-P-43496 F-1990 PARKA EXTREME COLD WEATHER《极端寒冷天气下用派克大衣》.pdf

《ARMY MIL-P-43496 F-1990 PARKA EXTREME COLD WEATHER《极端寒冷天气下用派克大衣》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-P-43496 F-1990 PARKA EXTREME COLD WEATHER《极端寒冷天气下用派克大衣》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-P-4347bF 4 W 7779706 0424873 T MIL-P-43496F 16 April 1990 SUPERSEDING MIL-P-43496E 31 December 1986 MILITARY SPECIFICATION PARKA, EXTREME COLD WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification cover

2、s one type of extreme cold weather parka made of cotton-nylon oxford cloth. 1.2 Classification. The parka shall be in the following sizes as specified (see 6.2). Schedule of sizes X-Small Sma 1 1 Medium Large X- La r g e c Beneficial comments (recommendations, additions, deletions) and any pertinent

3、 data which may be of use in improving this document should be addressed to: U.S. Army Natick, Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the Standardization Document Improvement Proposal (Da Form 1426) appearing at the end of this document or by letter. AMSC N/A F

4、SC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-4347bF LJ,M 77777Ob OLJ24872 L M MIL-P-43496F 2, APPLIChBLE DOCUMENTS 2.1 Government documents. *2.l.l Spe

5、cifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications an

6、d Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-203 V-B-87 1 V-F-106 V-T-280 J J-W- 155 CCC-C-438 DDD-L-20 PPP-B-636 MIL I TARY MIL-B-37 1 MI L-C-508 MIL-T-3530 MIL-C-3760 MIL-C-3924 MIL-T-5038 MIL-F-10884 MIL-C-17155 MIL-E-20652 MIL-L-350

7、78 MIL-C-43303 MIL-T-43548 MIL-T-43566 Paper, Kraft, Untreated Button, Sewing Hole, and Button, Staple, (Plastic) Fasteners, Slide, Interlocking Thread, Gimp, Cotton, Buttonhole Webbing, Textile , (Cotton, Elastic) Cloth, Buckram, Woven and Nonwoven Label: For Clothing, Equipage, and Tentage Boxes,

8、Shipping, Fiberboard (General Use) Braid, Textile, Tubular Cloth, Oxford,Nylon, 3 Ounce Thread and Twine; Mildew Resistant or Water Cloth, Flannel, Wool and Cotton; Wool and Nylon Cloth, Oxford, Cotton Warp and Nylon Filling, Tape, Textile and Webbing, Textile, Reinforcing, Fasteners, Snap Cloth, Kn

9、itted, Nylon, Fleece Eyelets, Metallic, Rolled, Flange Type; and Eyelet Loads, Units: Preparation of Semiperishable Repellent Treated Quarpe 1 Treated Nylon Washer Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification for Cord, Elastic Cotton Thread, Polyester Core: Cot

10、ton-, Rayon-, or Polyester-Covered Tape, Textile, Cotton or Polyester, General Purpose, Natural or in Colors 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-4347bF 4 m 777770b 0424873 3 m MIL-P-43496F STANDARDS FEDERAL FED-STD-751 - Stitches,

11、 Seams, and Stitch MILITARY MIL-SID-105 - Sampling Procedures and Tab es for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and

12、 military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Gavernment publications. The following documents form a part of this document to the extent specified herein. Unless oth

13、erwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODZSS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). THE COLOR ASSQC

14、IATION OF. THE UNITED STATES Standard Color Card of America Department of Defense Standard Color Card for Sewing Thread Department of Defense Standard Shades for Buttons Quartermaster Standard Shades of Slide Fastener Tapes (Color cards may be available from the Color Association of the United State

15、s, 343 Lexington Avenue, New York, NY 18016-0927, If color carda are not avail- able from the Color Association, individual color samples may be obtained from the contracting activity or as directed by the contracting activity.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Pra

16、ctice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the

17、documents. These documents also may be available in or through libraries or other informational services.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-43496F 84 W 999990b 0424874 5 m MIL-P-43496F 2.3 Order of precedence. In the event of

18、a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3 . REQUIREMENTS 3.1 Samples. 3.1.1 First article. Wh

19、en specified (see 6,2), a sample shal to first article inspection (see 6.3) in accordance with 4.3. be subjectec 3.1.2 Guide-sample. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variation from this specification may appear in the sample, in whic

20、h case this spec 3.2 Materials, It is encouraged that recycled practical as long as it meets the requirements of f ication shall gokern. material be used when this specification, 3.2.1 Basic material, The basic material shal be cotton warp and nylon filling oxford cloth, water repellent, Olive Green

21、 107 conforming to class 2 of MIL-C-3924 except that the colorfastness requirements for perspiration shall not apply* 3.2.2 Flannel. The material for lining side pockets shall be either 12 ounce, Olive Green 108, wool and nylon flannel cloth conforming to type III of MIL-C-3760 or 9.5 ounce minimum,

22、 Green 3405, knitted nylon fleece cloth conforming to type I of MIL-C-17155. 3.2.3 Cloth, nylon oxford, The material for pocket binding shall be 3-ounce nylon oxford cloth, OG-106, conforming to type I, class 2 of MIL-C-508. 3.2.4 Buckram, The material for interlining the collar shall be cotton buck

23、ram cloth conforming to type I, class 1, natural or bleached of CCC-C-438. 3.2.5 Webbing, elastic, The webbing for sleeve adjusting straps shall be cotton, elastic, 1-1/4 inches wide, Olive Drab 7 conforming to type I, class 8 of JJ-W-155. Alternatively, the webbing for sleeve adjusting straps shall

24、 be cotton, elastic, 1-1/4 inches wide, Olive Drab 7, shuttleless type conforming to type I, class 28 of JJ-W-155, 3.2.6 Tapes, reinforcing. 3.2.6.1 Webbing, nylon. The reinforcements for drawcord outlets, for socket portion of snap fasteners at back of parka, and for neck button tabs shall be nylon

25、 webbing, 1 inch in width, Olive Drab 7 conforming to type IV of MIL-T-5038. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-Ll347bF 84 W 777770b 042Ll875 7 H MIL-P-43496F 3.2.6.2 Tape. The tape for reinforcing the name tape shall be cotton,

26、1-1/2 inches in width, Olive Drab 7 conforming to type I, class 3 of MIL-T-43566. 3.2.7 Braids, drawcord. 3.2.7.1 Waist drawcord. The waist drawcord shall be solid tubular cotton braid conforming to type IV, class 1, 4/32 inch diameter or type V, class 1, 6/32-inch diameter, Olive Drab 7 of MIL-B-37

27、1. 3.2.7.2 Bottom drawcords. The drawcords at bottom of the parka shall be cotton elastic cord, 3/16 inch diameter, Olive Drab 7, conforming to class 2 of MIL-C-43303. 3.2.8 Resin impregnating agent. The resin agent used for dipping or impregnating the ends of the drawcords shall be cellulose acetat

28、e or cellulose acetate butyrate to prevent ravelling. The dipped or impregnated end shall be at least 1/2 inch in length (see table II, operation 1.i). 3.2.9 Hanger loop braid. The material for the hanger loop shall conform to type VII, class 2 of MIL-B-371. The color shall match the basic material.

29、 3.2.10 Thread, The thread shall he cotton-covered polyester thread conforming to MIL-T-43548, ticket numbers 30 and 50, 2 or 3 ply and 70, 2 ply. The thread shall be dyed Olive Drab -1, C.A. 6602% and shall be water-repellent treated in accordance with type II, class 3 of MIL-T-3530. 3.2.10.1 Color

30、fastness of thread. The dyed thread shall show fastness to light and laundering (after 3 cycles) equal to or better than the standard sample (see 6.4). When no standard sample is available, the dyed thread shall show “good“ fastness to light and laundering (after 3 cycles). 3.2.11 Gimp. The cotton g

31、imp or reinforcing buttonholes shall be size 8, Olive Drab S-1, C.A. 66022, conforming to type I or type II of V-T-280. 3.2.12 Buttons. The buttons shall conform to type II, class D, style 26, 30- line and style 20 or 21, 45-line of V-B-891. The color of the buttons shall be Olive Green hade BP, Cab

32、le No. 62016 and the finish shall be dull. 3.2.13 Fastener, slide, interlocking. The slide fasteners or the coat fronts shall be type IV, style 8, size MHS, 22 inches long individual element brass or molded plastic chain according to V-F-106 requirements except that the plastic chain shall have a cr

33、osswise breaking strength of 160 pounds (min). The tape shall be in accordance with V-F-106 requirements and dyed Olive Drab Shade S, Cable No. 66519. Plastic chain color shall match the tape and be equipped with a slider pull having a hole with sufficient size to accommodate the 3/8 inch thong. Bra

34、sa chain shall have a slider with wire stirrup pull and 3/8 inch thong. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-43496F 3.2.14 Snap fasteners. The snap fasteners shall conform to style 2A, brass, finish 2, male and female complete, con

35、sisting of stud and eyelet size 1 or 2 with button size 1 or 2 and socket of MIL-F-10884 except an unczpped button may be. used to attach the socket. 3.2.15 Eyelets. The eyelets for drawcord outlets shall be brass and conform to M20652/1-BBE 117 of MIL-E-20652, except that the finish chal approximat

36、e the shade of the basic material. shall 3.2.16 Labels. Each parka shall have a combination identification-s ze label and an instruction label conforming to type VI of DDD-L-20. The labels shall show fastness to laundering. Card of America are furnished for information and guidance as to the intensi

37、ty of the shade desired for the labels. The label shall be medium green. The following cable numbers of the Standard Color Cable No. 70034 Cable No. 70130 Cable No. 70131 3.2.16.1 Identification-size label. The combination identification-size label shall be a combination of class 1 and class 2 label

38、s. The size information shall be as follows: X-Sma 1 1 Sma 1 1 Medium Chest: Up to 33 inches Chest: From 33 to 37 in. Chest: From 37 to 41 in. Stock No. Stock No. Stock No. NATO Size: 7080/7484 NATO Size: 7080/8494 NATO Size : 7080/9404 Large X-Large Chest: From 41 to 45 inches Chest: From 45 inches

39、 and upward Stock No: Stock No: NATO Size: -7080/0414 NATO Size: 7080/1424 3.2.16.2 Instruction label. The instruction label shall conform to class 3, and contain the following information: PARKA, EXTREME COLD WEATHER 1, Wear as outer garment in cold-dry climate. 2, Button in liner for extra warmth.

40、 Remove it when 3, Button on fur ruffed hood for increased head protection, 4. damp or wet and allow to dry. Fasten drawstrings at waist and bottom for maximum warmth. Tighten sleeve cuffs by drawing elastic tabs tightly around wrists and buttoning tabs. 6 Provided by IHSNot for ResaleNo reproductio

41、n or networking permitted without license from IHS-,-,-MIL-P-4349bF 84 7777906 0424877 O MIL-P-43496F PARKA, EXTREME COLD WEATHER (contd) 5. Tie the drawstrings around each thigh to provide greater freedom of movement and an additional water repellent surfce to sit on, When bottom extension is not n

42、eeded, turn it up on inside af parka and fasten with snap fasteners. 6. Loosen drawstrings, open zipper, and unbutton elastic tabs on sleeve cuffs to ventilate. AVOID overheating. 7. Brush off snow and frost before entering heated shelters. 8. Avoid contact with heated stoves, open fires, or other h

43、igh 9. Lubricate brass slide fastener with lead pencil, graphite or wax. for machine washing in accordance with established procedure for Quarpel treated garments. The slide fastener shall be closed when laundered. 11. Pressing is acceptable provided the front flap of the parka overlaps the zipper a

44、nd the temperature of the steam press does not excced 3000F. When using a hand iron, do not iron over zipper. heat sources; fabric may fuse. 10. For cleaning and restoring of water repellency return to laundry BO NOT REMOVE THIS LABEL 3.2.16.3 Combination size, identification, and instruction label.

45、 The identification label (class i), size label (class 2) and instruction label (class 3) may be combined into one label. to the requirements of the class 14 label. The combination label shall conform 3.3 Design. The parka is a single breasted outer garment without hood and with slide fastener front

46、 closure with snap fasteners, sleeves with adjustable cuffs, two slit type breast pockets with flap and snap fastener closure, waist and hem line drawcords, inside buttons for attachment of liner, and buttonholes on stand-up collar for attachment of fur ruffed hood. 3.4 Figure. Figure 1 is furnished

47、 for information only. If there are any inconsistencies between the written specification and the figure, the tiritten specification shall control. 3.5 Patterns. Standard patterns shall be furnished by the Government and will provide an allowance of 1/2 inch for double-lapped and double-stitched sea

48、m and 3/8 inch for all other seams. The standard patterns are provided as a guide or cutting contractors working patterns and shall not be altered in any way. The working patterns shall be identical to the standard patterns. 3.5.1 List of pattern parts. The pattern parts shall be cut from material a

49、s specified and according to the number of parta listed in table I. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ MIL-P-4347bF 84 W 777770b OLl24878 2 W MIL-P-43496F TABLE I. List of pattern parts Materials Nomenc I. a ture Cut parts Cotton warp and nylon Collar filling, oxford cloth Right front Left front Back Pocket flap Sleeve adjustment tab Pocket welt Hanging pocket Lef