ARMY MIL-L-43498 D-1990 LINER COLD WEATHER TROUSERS FIELD《野外冬季裤衬里》.pdf

《ARMY MIL-L-43498 D-1990 LINER COLD WEATHER TROUSERS FIELD《野外冬季裤衬里》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-L-43498 D-1990 LINER COLD WEATHER TROUSERS FIELD《野外冬季裤衬里》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POLiiD I MIL-L-43498D 12 September 1990 SUPERSEDING MIL-L-4349% 19 September 1983 MILITARY SPECIFICATION LINER, COLD WEATHER TROUSERS, FIELD This specification is approved for use by all Departments and Agencies of the Department of Defense. 1, SCOPE 1.1 Scope, This specification covers a trous

2、er liner made from quilted polyester batting material, for the cold weather field trousers. 1.2 Classification. The liner shall be of one type in the following sizes (see 6.2): Schedule of sizes Short and Regular Long X-Sma 1 1 Small Medium Large X-Large 2. APPLICABLE DOCUMENTS 2.1 Government docume

3、nts. X-Sma 11 Small Medium Large X-Large Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the Standard

4、ization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited, - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

5、-,-,-MIL-L-4349D 4 m 9999906 0454827 3 W MIL-L-43498D 2.1.1 Specifications, standards, and handbooks. The following sDecificationc, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these are those listed in the issue of t

6、he Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-203 - Paper, Kraft, Untreated A-A-50198 - Thread, Gimp, Cotton, Buttonhole A-A-50199 - Thread, Polyester Core, Cotton- or Polyester Covered

7、V-B-87 1 - Button, Sewing Hole, and Button, Staple, (Plastic) J J-W- 155 - Webbing, Textile, (Cotton, Elastic). DDD-L-20 - Label: For Clothing, Equipage, and Tentage, PPP-B-636 - Boxes, Shipping, Fiberboard (General Use) MI LI TARY MIL-C-508 - Cloth, Oxford, Nylon, 3 Ounce MIL-L-35078 - Loads, Unit:

8、 Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For MIL-B-41826 - Batting, Synthetic Fibers, Polyester, (Unquilted and Qu i 1 ted) STANDARDS FEDERAL FED-STD-751 - Stitches, Seams and Stitchings MI LI TARY MIL-STD-105 - Sampling Proce

9、dures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STB-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks ere a

10、vailable from the Standardization Documents Order Desk, Building 4D, 700 Rsbbins Avenue, Philadelphia, PA 19111-5094.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(Application for copies should be addressed to the American Society for Testing a

11、nd Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services,) 2.3 O

12、rder of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes prece- dence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. O MIL-L-43498D

13、2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the i

14、ssues of documents not listed in the DODISS are the issues of the documents cited in the solicita- tion (see 6.2). THE COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card of America Department of Defense Standard Color Card for Sewing Threads (Color cards may be available from the Color Assoc

15、iation of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color cards are not available from the Color Association, ind-ividual color smaples may be obtained from the contracting activity or as directed by the contracting activity.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (AS

16、TM) D 3951 - Standard Practice for Commercial Packaging 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.31, in accordance with 4.3. 3.2 Guide sample. Guide samples, when furnished, are solely for the guidance and information

17、 to the contractor (see 6.3). appear in the sample, in which case this specification shall govern. Variation from the document may 3.3 Materials. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.3.1 Basic material. The basic

18、 material shall be quilted polyester batting, conforming to type IV, class 1, style a, of MIL-B-41826. .” 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-L-4347D Lt W 777770b 045Lt27 7 W - MIL-L-43498D 3.3.2 Waistband and binding. The material

19、 for waist lining, side opening facings, and bias binding shall be nylon oxford cloth, dyed Olive Green 106, conforming to type I, class 2 of MIL-C-508, except that the colorfastness requirements to light and wet-drycleaning shall not apply. 3.3.3 Labels. Each liner shall have an identification labe

20、l, a size label, and an instruction label conforming to DDD-L-20, except label color shall be Medium Green, Cable Nos. 70034, 70130, or 70131 (see 2.2). Fastness to laundering, requirements shall apply. 3.3.3.1 Identification label; The identification label shall conform to type VI, class 1. 3.3.3.2

21、 Size label. The size label shall conform to type VI, class 2 and shall contain the following information for each respective size: X-Small - Short and Regular X-Small - Long Waist: Below 27 inches Inseam: Up to 32-1/2 inches Stock No: NATO Size: 6783/5869 Waist: Below 27 inches Inseam: Over 32-1/2

22、inches Stock No: NATO Size: 8390/5869 Small - Short and Regular Small - Long -Waist: From 27 to 31 inches Inseam: Up to 32-1/2 inches Stock No: NATO Size: 6783/6979 Medium - Short and Regular Waist: From 31 to 35 inches Inseam: Up to 32-1/2 inches Stock No: NATO Size: 6783/7989 Large - Short and Reg

23、ular Waist: From 35 to 39 inches Inseam: Up to 32-1/2 inches Stock No: NATO Size: 6783/8999 X-Large - Short and Regular Waist: From 39 to 43 inches Inseam: Up to 32-1/2 inches Stock No: NATO Size: 6783/9909 Waist: From 27 to 31 inches Inseam: Over 32-1/2 inches Stock No: NATO Size: 8390/6979 Medium

24、- Long Waist: From 31 to 35 inches Inseam: Over 32-1/2 inches Stock No: NATO Size: 8390/7989 Large - Long Waist: From 35 to 39 inches Inseam: Over 32-1/2 inches Stock No: NATO Size: 8390/8999 X-Large - Long Waist: From 39 to 43 inches Inseam: Over 32-1/2 inches Stock No: NATO Size: 8390/9909 4 Provi

25、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43498D 3.3.3.3 Instruction label. The instruction label shall conform to type VI, class 3 and shall contain the foilowing information: LINER, COLD WEATHER TROUSERS, FIELD I, Button into trousers for ex

26、tra warmth. 2. Buttoning side openings for easy removal. 3. Dry liner and trousers separately. 4. Avoid contact with heated stoves, open fires or other heat 5. DO NOT DRY CLEAN. sources; fabric may fuse. detergent, rinse thoroughly, and drip dry or machine dry. Wash by hand or machine in warm water

27、with mild soap or DO NOT REMOVE THIS LABEL 3.3.3.4 Combination size and identification label. The identification label (class 1) and the size label (class 2) may be combined into one label conforming - to type VI, classes 1 and 2 combined. 3.3.3.5 Combination size, identification and instruction lab

28、el. The identifi- cation label (class i), size label (class 2) and instruction label (class 3) may be combined in one label conforming to class 14. The coating requirement shall conform to class 3 label. 3.3.4 Thread. The thread shall be cotton or polyester covered polyester core conforming to A-A-5

29、0199, ticket number 30, 2 or 3 ply or 50-2 ply for stitching and seaming, 70-2 for overedging, and 30, 2 or 3 ply for buttonholes and button sewing. The thread shall be dyed Olive Drab S-1 C.A. 66022. 3.3.4.1 Colorfastness. The dyed thread shall show fastness to laundering equal to or better than th

30、e standard sample. When no standard sample is available, the dyed thread shall show “good“ fastness to laundering. 3.3.5 Gimp. The cotton gimp for reinforcing buttonholes shall be no. 8, dyed Olive Drab S-1 C.A. 66022, conforming to A-A-50198. 3.3.5.1 Colorfastness. The dyed gimp shall show fastness

31、 to laundering equal to or better than the standard sample. When no standard sample is available, the dyed gimp shall show “good“ fastness to laundering. 3.3.6 Buttons. The buttons shall be type II, class D, style 26, 30-line of V-B-871. The buttons shall be Olive Green BP, C.A. 62016 with a dull fi

32、nish. 3.3.7 Elastic. The elastic for the waistband shall be type I bleached or unbleached, class 6 of JJ-W-155. 3.4 Design. The design of the liner shall be a button in liner with buttoned Side openings for easy removal (see figure i), 5 Provided by IHSNot for ResaleNo reproduction or networking per

33、mitted without license from IHS-,-,-MIL-L-4347D Lt W 777770b 0454833 5 MIL-L-43498D 3.5 Patterns. Standard patterns to be used to cut working patterns will be The patterns provide furnished by the Government, The working patterns shall be identical to the standard patterns which shall not be altered

34、 in any way. 1/2 inch seam allowance for all seams (to finish 3/8 inch wide). 0 3.5.1 Pattern parts. The component parts shall be cut from the materials . specified below in accordance with pattern parts indicated in table I. TABLE I. List of pattern parts Mat er i a 1 Pattern nomenclature Cut parts

35、 Basic material Front Back 2 2 3.6 Construction. The construction shall conform in all respects to the requirements specified in table II and herein. guidance and information. Should variation from this specification appear in figure 1, this specification shall govern. Figure 1 is furnished solely f

36、or 3.6.1 Stitches, seams, and stitching. All stitches, seams and stitching shall conform to FED-STD-751. The type of seam, stitching and stitches per inch shall be as specified in table II. Seam allowance shall be maintained with seams sewn so that no raw edges, run-Offs, pleats, puckers, or open se

37、ams occur. When two or more methods of seams or stitches are given for the same operation, any one may be used. Where stitch type 401 is used, the looper (underthread) may be on the outside or the inside of the liner. The reverse,side of the seam type LSbm-3 (overedge side) shall be on the outside o

38、f the liner. The side of the liner worn nearest the body shall be considered the inside. 3.6.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched not less than 1/4 inch except where ends are turned under or caught in other seams or stitching. Ends of a continuous line

39、of stitching shall overlap not less than 1/2 inch. there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering of the materials sewn. The lock shall be imbedded in the materials sewed. Thread tensions shall be maintained so that I 3.

40、6.1.1.1 Repairs of type 301 stitching. 3.6.1.1.1.1 Quilty batting stitching. Broken stitches of the quilting pattern may be repaired by stitching back of each end of break not less than 1 inch. 3.6.1.1.1.2 Liner fabrication stitching. 6 Provided by IHSNot for ResaleNo reproduction or networking perm

41、itted without license from IHS-,-,-MIL-L-43498D When thread breaks or bobbin run-outs occur during stitching, except a. prestitching, the stitching shall be repaired by restarting the stitching a minimum of 1/2 inch back of the end of the stitching. - i/ b. Except for prestitching, thread breaks, or

42、 two or more consecutive skipped or run-off stitches noted during inspection of the item shall be repaired by overstitching. The stitching shall start a minimum of 1/2 inch in back of the defective area, continue over the defective area, and continue a minimum of 1/2 inch beyond the defective area o

43、nto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials, and restitching in the required manner. L/ - i/ When making the above repairs, the ends of the stitching are not required to be backstitched. 3.6.1.2

44、 Type 401, 503, 504, 515, 516, 517, 518 and 519 stitching. Thread tension shall be maintained CO that there will be no loose stitching. All repairs shall be in accordance with 3.6.1.1.1.2a and 3.6.1.1.1.2b. Thread tension shall be maintained so that there will be no loose or excessively tight stitch

45、ing resulting in puckering or the materials sewn. 3.6.2 Buttonholes. The buttonholes shall be the eyelet-end-taper-bar-type worked over gimp (see 3.3.5) with not less than four tacking stitches at bar end (not counting cross-over stitch). inches. the fabric. The finished cut length shall be 3/4 to 7

46、/8 The buttonholes shall be clean cut with the stitching securely caught in 3.7 Manufacturing operations requirements. The liner shall be manufactured in accordance with operations specified in table II. The contractor is not required to follow the exact sequence of operations. stitching may be used

47、 providing the threads are removed or are not visible on the finished liner. Any additional basting or holding 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-43478D 4 W 777770b 0454833 7 W ru t; e, W H w I4 4 - Y Mii-i-43498D I al 4 *-I al1

48、5c 4 C oal c Mci C - o VU C *-I E n4 O alcy ce ci Ob U 4c CI uc ld -ci v) w O am O QC 4 c, c gc. . tun u 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-L-4347D 4 = 9797706 0454835 2 u. 4 I 2 W al w w O 4 -i a c ln I ci C O O W aw 4 3 a4 c, id

49、c 4 c M E vu o a OP u W O a e, n v) al v) C *-I a C m 9 a 9 al v) c, a e, rn a 3 u 2 al v) c, V C O b .4 O Y al C 90 M LI alt se, oc z 2 c, he, O me, e,bn DM U Lia Li u tic0 boa Ut -I e, *u a amo v1 ti v; a W C c T ZU mn mc U - L U 2 - t; 8 z MIL-i-43498D O O0 O O O0 O O O in r-wl r- VI bin b in b O O0 O o .o o O O O in in- in in -VI in in U U l I + 4 z 4: 5 I O M U I + 2 wvi w N I dd 4 or off center on