ARMY MIL-H-48671-1988 HOLSTER HIP M12《M12手枪皮套 热等静压机》.pdf

《ARMY MIL-H-48671-1988 HOLSTER HIP M12《M12手枪皮套 热等静压机》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-H-48671-1988 HOLSTER HIP M12《M12手枪皮套 热等静压机》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-H.- 4 8 6 7 1 2 February 1988 (AR) t distribution is unlimited. 7 . THIS DOCUMENT CONTAINS I PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-48671 (AR) MILITARY MIL-STD- 10 5 -Sampling Procedures and Tables for MIL-STD-109 -Quality A

2、ssurance Terms and Definitions. MIL-STD-13 0 -Identification Marking of U.S. Military 2.1.2 Other Government documents, drawings and publications. Inspection by Attributes. Property. The following other Government documents, drawings and publications form a part of this specification to the extent s

3、secified herein. Unless otherwise specified, the issues shall be those listed in effect on the date of solicitation. DRAWINGS U.S. ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) 9388057 Holster, Hip, M12 SP 193 8 80 57 Special Packaging Instructions for Holster, Hip, M12 (Copies

4、of specifications, standards, drawings, publications and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.1.3 Order of precedence. a In the event of a c

5、onflict between the text of this specification and the references cited herein, (except for associated detail specifications, specification sheets or MS standards) specificat;ion shall take precedence . Nothing in this specification, however, shall supersede applicable laws and regulations unless a

6、specific exemption has been obtained. the text of this 3. REQUIREMENTS 3:1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection in accordance with the technical provisions herein (see 4.4 and 6.2) . 3.2 Materials and construction. H

7、olsters and parts shall conform to the materials, dimensions, conditions and construction requirements specified herein, and on Drawing 9388057 and drawings applicable thereto, and shall be in accordance with the applicable mater ia1 and construct ion provisions of MIL-W-13855 . c 2 , Provided by IH

8、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-Li673 30 7779706 0323306 3 MIL-H-48671 (AR) 3.2.1 Stitches, seams and stitchings. All stitches, seams o and stitchings shall conform to FED-STD-751, type 301 and 304. 3.2.1.1 Repairs of type 301 stitching. Repa

9、irs of type 301 stitching shall be as follows: a. Thread breaks or bobbin run-outs which occur during stitching shall be repaired by restarting the stitching a minimum of one half inch in back of the stitching end. b. Thread breaks and skipped stitches shall be repaired by overstitching. The stitchi

10、ng shall start a minimum of one inch in back of the defective area, continue over the defective area and onto the existing stitching a minimum of one inch beyond the 4 defective area. c. When making the repairs specified in a. or b. above, stitching ends are not required to be backstitched. d. Loose

11、 or excessively tight stitching shall be repaired by removing the defective stitching, without damaging the materials, and restitching in the required manner. 3.2.1.2 Repairs of type 304 stitching. Thread breaks, bobbin runouts, skipped or loose stitches shall be repaired by completely removing the

12、stitching, without damaging the materials, and restitching in the required manner. 3.2.2 Thread ends. All thread ends shall be trimmed to a one fourth inch maximum length. 3.2.3 Webbing ends. All exposed webbing ends shall be hot cut or fused to prevent fraying. 3.3 Performance characteristics. 3.3.

13、1 Interface and fit. The holster shall be capable of proper interface and fit with the M9 pistol. Neither complete insertion nor withdrawl of the pistol- shall cause functionally significant movement of any of the pistols controls (e.g., the safety shall not be moved from the safe to the fire positi

14、on or vice versa; the magazine catch shall not release the magazine; the slide or hammer shall not be retracted so as to cause the hammer to approach the half-cocked position) . 3.3.2 D-ring fla9. The force required to release the flaps D-ring when an M9 pistol is completely inserted into the holste

15、r shall not be less than 6 lbs, nor more than 10 lbs. 3.3.3 D-ring flap. The force required to release the flap D-ring when the holster is empty shall not be less than 3 lbs. i 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-467L LO 7779706 0

16、323307 5 MIL-H-48671 (AR) 3.3.4 Belt fastener. The force required to release each side a of the belt fastener wireform shall not be less than 8 lbs, nor more than 12 lbs. 3.3.5 Belt fastener assembly. The belt fastener assembly wireform shall be capable of free standing within its own weight at 900

17、to the backplate. The weight required for downward movement beyond 45O shall not exceed 12 ounces. 3.4 Identification marking. Each holster shall be idelibly marked with the letters “US“, “M12“, part number, manufacturers name and FSCM code. Markings shall be molded positive or negative iii relief o

18、n the plastic facing, conform to MIL-STD-130 and- be in the location and size indicated on the applicable drawing. instruction sheet ect criteria as ssecified in 4.5.4.1. to determine that packaging, packing and marking requirements comply to section 5 requirements. Inspection shall be in accordance

19、 with the classification of defects listed below. The sample unit shall be one shipping container fully packaged. The iot size shall be the number of containers in the inspection lot. The inspection level shall be S-4 with an AQL of 4.0 defects per hundred units in accordance with MIL-STD-105. 4.5.6

20、 Examination of packagia. An examination shall be made Characteristic Marking Workmanship Content Materials Defect Omitted; incorrect; illegible; of improper size, location, sequence, or method of application. Improper taping, incomplete closure, bulged or distorted container. Number of holsters per

21、 container is more or less than specified. Any omitted, damaged, or not as specified. 4.6 Methods of. inspection. 4.6.1 Interface and fit test. Test samples selected for interface and fit testing shali be suspended as in service. A sistol for which the holster was designed shall be manually inserted

22、 and withdrawn to determine conformance with the requirements. This ogeration shall not be repeated more than once and any non-conformance shall consti.tute a defect. 4.6.2 Loaded holster D-rinq force test. Test samples shall be tested on a push-pull force test fixture conforming . substantially t F

23、igre 1. The sample holster shall be mounted, an M9 ;?isto1 comgletely inserted, and flap assembly closed and latched. The gage rod shall engage the D-ring and downward force applied, in conjunction with outward movement of the holster body, until the lid latch wire is released from the holster body

24、facing. Failure to meet the specified release force requirement shall constitute a defect. Y 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-4b71 LO 9 7777706 03231L9 2 W MIL-H-48671 (AR) 4.6.3 Empty holster D-ring force test. Test samples s

25、hall be tested on a push-pull force test fixture conforming substantially to Figure 1. assembly closed and latched. The gage rod shall engage the D-ring and downward force applied, in conjunction with outward movement of the holster body, until the lid latch wire is released from the holster body fa

26、cing. requirement shall constitute a defect. The sample holster shall be mounted with the flap Failure to meet the specified release force 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-4b71 LO W 9777706 0323LL5 4 MIL-H-48671(AR) -O PUSH HA

27、NDLE PUSH PULL FORCE GAGE PULL HANDLE ROTATION - II . ROT& .TION I bAOE ROD LD-RING -HOLSTER b L I FIGURE 1. Push-pull force test fixture. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-4b73 10 E 777370b 0323336 b I MIL-H-48671 (AR) 4.6.4 B

28、elt fastener force test. Test samples shall be tested 0 on a push force test fixture conforming substantially to Figure 2. The sample holster shall be securely clamped to the test fixture. The gage rod shall engage the belt fastener wire and outward force applied until release is visually noted. Eac

29、h side of the belt fastener shall be tested for conformance to this requirement. Failure of either side to be within the required tolerance shall constitute a defect. l a I 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-48671 (AR) FORCE GAG

30、E TOP VIEW FRONT VIEW FIGURE 2. Push force test fixture. ici Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-0 . MIL-H-48671 (AR) 4.6.5 Belt fastener assembly test. The belt fastener assembly shall be clamped vertically by the backplate to allow upwa

31、rd and downward movement of the wireform. The wireform shall be raised as specified and dead weight applied to either end to determine conformance with the requirements. 5. PACKAGING 5.1 Level A. Packaging shall be in accordance with Special Packaging Instructions P9388057 5.2 Level B. Packaged as s

32、pecified in 5.1. 5.3 Level C. Packaged as specified in 5.1. 6. NOTES 6.1 Intended use. The holsters covered by this specification are intended to be used as left or right hip holsters for the M9 pistol. following: 6.2 Ordering data. Acquisition documents should specify the a. Title, number and date

33、of this specification. b. Instructions for first article sample (see 3.1 and 4.4) c. Lists of drawings and specifications pertinent to the d. Identification of Government furnished property and ho Is ter showing app 1 icab le r ev is ion da te s . disposition. e. Level of packaging (see section 5) 6

34、.3 Inspection equipment design. Design responsibility for all inspection equipment is assigned to the contractor. Contractor designs are required for all inspection equipment and may include commercial equipment which the contractor proposes to use. (Commercial equipment is defined as unmodified equ

35、ipment which is catalogued and available for purchase by the general public). Contractor designs shall include appropriate operating ins truc t ion s, calibration procedures and maintenance procedures . Commercial equipment shall be fully described by catalog listings or other means which provide su

36、fficient information to permit identification and evaluation by the Government and may include illustrations and engineering data. Designs shall be prepared for any special fixture(s) required to be used with commercial equipment or with SIE designs if not otherwise covered thereby. 15 I Provided by

37、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H- 48 6 71 (AR) Designs shall be of the category and form (per DOD-D-1000) specified in the Contract Data Requirements List (DD Form 1423). The specification number, paragraph number and defect description/num

38、ber from section 4 shall be referenced on each contract or design together with the component or assembly drawing number, revision letter and date to which the specific design app 1 ie s. 6.3.1 Submission of desiqns for approval. Contractor designs shall be approved by the Government prior to fabric

39、ation or procuring the equipment. Designs shall be submitted for approval in accordance with the stipulation, time frame and distribution specified in the Contract Data Requirements List (DD Form 1423) or in the contract. Partial submission of inspection equipment designs is permissible and encourag

40、ed. However, the completion date for design review will be based on the date of the final submission of designs and the required delivery schedule as stipulated in the contract. The address for submission of contractor designs will be specified on the contract Data Requirements List, DD Form 1423 in

41、 the contract. Unless otherwise specified, data item DI-R-1714 will apply. When the contractor submits inspection equipment designs to the Government for approval, he shall give the following information in his letter of transmit tal. a. The contract number. b. The contract item (name, model number,

42、 etc.) c. The designs remaining to be submitted and the expected date of submittal. 6.4 Drawings. Drawings listed in Section 2 of this specification under the heading US Army Armament Research, Develop- ment and Engineering Center (ARDEC) may also include drawings prepared by, and identified as Edge

43、wood Arsenal, Frankford Arsenal, Rock Islqnd Arsenal, Picatinny Arsenal, US Army Armament Research and Development Command (ARRADCOM) drawings. Technical data originally prepared by these activities are now under the cognizance of ARDEC. 6.5 Subject term (key word) listing. Holster Military Specification M12 Small arms Custod ian : Army-AR (Project 1005-A716) 16 Preparing activity : Army-AR Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-