ARMY MIL-F-44434-1992 FLASHLIGHT LIGHTWEIGHT《轻型手电筒》.pdf
《ARMY MIL-F-44434-1992 FLASHLIGHT LIGHTWEIGHT《轻型手电筒》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-F-44434-1992 FLASHLIGHT LIGHTWEIGHT《轻型手电筒》.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-F-44434 62 E 9999906 0501467 5 PI 17 Januarv 1992 MILITARY SPECIFICATION FLASHLIBEI, LIBFIWEIrn This specification is approved for use by Natick Research, Developent, and Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Def
2、ense. 1. SCOPE 1.1 Scope. This specification covers a lightweight flashlight (to be powered by two “AA“ batteries) which will provide red or white light by means of an integral, movable, red filter. 1.2 Classification. The flashlights shall be the following types as specified (see 6.2). Type I - Fla
3、shlight without batteries Type II - Flashlight with batteries 2. APPLICABLE DocuMENIv3 2.1 Government documents. 2.1.1 Specifications, standards, and handkmks. The following specifica- Unless otherwise specified, the issues of these documents tions, standards, and handboks form a part of this docume
4、nt to the extent specified herein. are those listed in the issue of the Demnt of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial cmnts (recmndations, additions, deletions) and any pertinent data which my be used in improv
5、ing this document should be addressed to: Center, Natick, MA Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. U.S. Army Natick Research, Developnt, and Engineering 01760-5019 by using the Standdization D0C;ument AMSC N/A FSC 6230 DISTRIBUTION STATEMENT A. Appro
6、ved for public release; distribution is unlimited, O Licensed by Information Handling ServicesMIL-F-44434 62 m 9999906 8501468 7 I SPECIFICATIONS PPP-B-566 - Boxes, Folding, Paperboard PPP-E-636 - Boxes, Shipping, Fiberboard MILITARY MIL-B-18/7 - Battery, Dry, BA-27 MIL-P-116 - Preservation, Methods
7、 of MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipnt and Equipage; General Specification For STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Irispection by Attributes MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147
8、- Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets (Unless otherwise indicated, copies of federal and military specifications, standards, and handhoks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA
9、19111-5094.) 2.2 Non-Government publications. The following dccuments form a part of this document to the extent specified herein. the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documents not listed in the DODISS
10、 are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, Unless othemise specified, AMERICAN SOCIm FOR TESTING AND MATERIALS (ASTM) D 2000 - Standards Classification System for Elastomeric Materials for D 3951 - Standard Practice for Carmercial Packaging Auto
11、motive Application (Application for copies should be addressed to the American Society for Testing and Materials, 1919 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. T
12、hese documents also my be available in or through libraries or other informa- tional services.) 2 t Licensed by Information Handling Services-_ MIL-F-44434 62 W 9999906 05BL469 9 W 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein,
13、the text of this document takes precedence. Nothing in this document, however, supersedes applicabl laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENIIS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in a
14、ccordance with 4.3. 3.2 Material. The material shall be specified herein. However, when a material is not specified, a material shall be used which will enable the flashlight to conform to the performance requirements of this specification. It is encouraged that recycled material be used 3.2.1 Recyc
15、led material. when practical as long as it meets the requirements of this specificatio 3.3 Components. The flashlight components shall consist of a lamp head battery housing, pocket clip, red filter, lamp, spare lamp, lanyd ri switch. 3.4 Construction. The flashlight shall be so constructed that no
16、parts will work loose in service. strains, jars, vibrations, and other conditions incident to shipping, storage, installation, and service. anodized aluminum and shall be designed to house two size “AA“ batteries and to prevent inserted batteries from damaging the base of the lamp, reflector, or any
17、 internal part which could render the flashlight unserviceable when impact tested as specified in 4.4.2. shall be so designed that the batteries can be easily replaced without the use of tools. The flashlight shall be built to withstand the 3.4.1 Battern housing. The battery housing shall be fabrica
18、ted of e The flashlight and battery housing 3.4.2 Lamp head. The lamp head shall include the lamp socket, red filter, lamp housing, and lamp. lamp can be easily replaced without the use of tools. capable of providing at least 20 foot-candles of illumination when testa specif ied in 4.4.2 without fil
19、ter. The lamp shall have a minimum life f hours of continuous operation and shall not becm loose or displaced dur rough handling when impact tested as specified in 4.4.2. The head shall be so designed that the The lamp head shall 3.5 Holder for spare lamp. Each flashlight shall be furnished with a s
20、pare lamp. flashlight in such a manner so as to be accessible and shall not become loose or displaced when impact tested as specified in 4.4.2. The spare lamp shall be mounted in a holder within the,- 3 Licensed by Information Handling Services- MIL-F-44434 b2 I 9999906 0501470 5 S . i) 3.6 Gaskets.
21、 Gasket shall be provided on all flashlights, where necessary, to prevent the entrance 0.f moisture into the interior of the flashlight or into the switch contacts. rubber or synthetic rubber composition conforming to AS?M D2000, grades 3AA510B13C12F17, 3AA610B13C12F17, or 3AA710B13C12F17. Gaskets s
22、hall be fabricated from 3.7 Red filter. The flashlight shall include an integral red filter which can be mved into place over the lamp and mved away from the lamp without the use of tools and without any assembly or disassembly of the flashlight. When the filter is in place over the lamp, it shall p
23、ermit at least 6 percent of the light emitted by the lamp to leave the flashlight. approved means shall be provided to“ensure positive positioning of the filter. A detent or other 3.8 Switch. The switch shall be a “push on-push off“ switch mounted on the side of the flashlight. operated with one han
24、d. accidently be operated or snagged on other clothing or equipnt. shall not have internal electrical leakage when tested as spcified in 4.4.2. cycles when endurance tested as specified in 4.4.2. guarded to protect it from damage when impact tested as specified in 4.4.2. The flashlight shall not go
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILF444341992FLASHLIGHTLIGHTWEIGHT 轻型 手电筒 PDF
链接地址:http://www.mydoc123.com/p-444644.html