ARMY MIL-DTL-3628 26 K-2012 BADGE QUALIFICATION DIVER.pdf

《ARMY MIL-DTL-3628 26 K-2012 BADGE QUALIFICATION DIVER.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 26 K-2012 BADGE QUALIFICATION DIVER.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 3 FSC 8455 DETAIL SPECIFICATION SHEET BADGE, QUALIFICATION, DIVER This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the late

2、st issue of MIL-DTL-3628. PIERCED (REGULAR SIZEONLY) -1,- 5,-9 Master Diver -2,-6,-10 First Class Diver -4,-8,-12 Salvage Diver -3,-7,-11 Second Class Diver DASH NUMBERS: -1 Master Diver, Regular Size (A) -7 Diver 2nd Class, Dress Miniature(A) -2 Diver 1st Class, Regular Size (A,N,CG) -8 Diver, Salv

3、age, Dress Miniature (A) -3 Diver 2nd Class, Regular Size (A,N,CG) -9 Master Diver, Regular Size, Subdued (A) -4 Diver, Salvage, Regular Size (A) -10 Diver 1st Class, Regular Size, Subdued (A) -5 Master, Diver, Miniature Size (A) -11 Diver 2nd Class, Regular Size, Subdued (A) -6 Diver 1st Class, Dre

4、ss Miniature (A) -12 Diver, Salvage, Regular Size, Subdued (A) INCH-POUND MIL-DTL-3628/26K 10 December 2012 SUPERSEDING MIL-DTL-3628/26J 15 November 1996 PIERCED ALL SIZE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/26K Page 2 of 3 MA

5、TERIAL: (-1 through -8): Red Brass 85/15 (UNS Alloy No.C-230) or Nickel Silver 65/15 (UNS Alloy No. C-752) (-9 through -12): Red Brass 85/15 (UNS Alloy No. C-230) FINISH: (-1 through -8): Nickel Plated (Red Brass only), Silver Plated, Oxidized, Relieved, Matte Finish and shall match The Institute of

6、 Heraldry (TIOH) Metal Finish Chip Number 14. (-9 through -12): Dull, Flat Black TIOH Metal Finish Chip Number 21. DIMENSIONS: HEIGHT (Overall): -1,-9: 1-1/4 inches (REF) -5: 13/16 inch (REF) -3, -4, -11, -12: 1 inch (REF) -6: 21/32 inch (REF) -2,-10: 1-1/16 inches (REF) -7, -8: 5/8 inch (REF) WIDTH

7、 (Overall): -1, -2, -9, -10: 1-3/32 inches (REF) -5, -6: 11/16 inch (REF) -3, -4, -11, -12: 23/32 inch (REF) -7, -8: 7/16 inch (REF) THICKNESS: (At face window) -1 thru -4, -9 thru -12: 0.135 inch + .010 inch -5 thru -8: 0.095 inch + .005 inch THICKNESS: (At edge): -1, -2, -3: 0.075 inch + .005 inch

8、 -4, -5, -6: 0.063 inch + .005 inch ATTACHING DEVICE: 1. The attaching device shall be prong and clutch type. 2. The prongs for -1, -2, -5, -6, -9, and -10 shall be located on the horizontal center line, equidistant from each end the distance apart as indicated below. 3. The prongs for -3, -4, -7, -

9、8, -11, and -12 shall be located on the vertical center line, equidistant from each end and the distance apart as indicated below. DASH NO. DISTANCE APART -1, -2, -9, -10 7/8 inch + 1/64 inch -3, -4, -11, -12 3/4 inch + 1/64 inch -5, -6, -7, -8 1/2 inch + 1/64 inch Provided by IHSNot for ResaleNo re

10、production or networking permitted without license from IHS-,-,-MIL-DTL-3628/26K Page 3 of 3 NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished hub or die. 2. Piercings shall be as indicated. 3. Army items for -1 through -8 may be nickel plated mirror-like polish

11、ed finish which shall match TIOH Metal Finish Chip Number 16 for commercial sale only. For nickel plated items, silver plating requirement shall not apply. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue

12、were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relati

13、onship to the last previous issue. Custodians: Preparing activity: Army - IH Army IH Air Force -11 Navy - NU Review activities: (Project No. 8455-2013-011) Navy - CG1 DLA CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-