ARMY MIL-DTL-3628 259-2013 BADGE IDENTIFICATION COMMAND-AT-SEA CHIEF ENGINEER MILITARY SEALIFT COMMAND U S NAVY.pdf

《ARMY MIL-DTL-3628 259-2013 BADGE IDENTIFICATION COMMAND-AT-SEA CHIEF ENGINEER MILITARY SEALIFT COMMAND U S NAVY.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 259-2013 BADGE IDENTIFICATION COMMAND-AT-SEA CHIEF ENGINEER MILITARY SEALIFT COMMAND U S NAVY.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 INCH-POUND MIL-DTL-3628/259 4 March 2013 DETAIL SPECIFICATION SHEET BADGE, IDENTIFICATION, COMMAND-AT-SEA, CHIEF ENGINEER, MILITARY SEALIFT COMMAND, U.S. NAVY This specification is approved for use by all Departments and Agencies of the Department of Defense The require

2、ments for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-3628. DASH NUMBER: -1 Dress Size Badge -2 Regular Size Badge MATERIAL (-1 and -2): Red Brass (UNS Alloy No. C-230) FINISH (-1 and -2): 24K Gold Plated, Matte Finish, Polished Hi

3、ghlights and shall match The Institute of Heraldry Standard Metal Finish Chip Number 8. DIMENSIONS: DIAMETER: -1: 1-1/2 inches (REF) -2: 3/4 inch (REF) THICKNESS (across scroll): -1: 0.115 inch 0.010 inch -2: 0.078 inch 0.010 inch PIERCING: Piercings shall be made where indicated above for the manuf

4、acture of -1 only. -2 shall not be pierced. Piercings are to be made for manufacture of -1 only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3628/259 Page 2 of 2 ATTACHING DEVICE: -1: Attaching device shall be prong and wing-grip clutch t

5、ype with three prongs. Each prong shall have an overall length of 5/16 inch + 1/8 inch - 0 and be either fused or hard soldered to the badge. The two prongs at the top of the badge shall be located along the outer band, 34 1 above the horizontal center line, and positioned 1/16 inch + 1/32 inch - 0

6、from the edge of the badge. The single prong at the bottom of the badge shall also be located on the outer band along the vertical center line, dissecting the two prongs at top. The bottom prong shall be positioned 1/16 inch + 1/32 inch - 0 from the edge of the badge. -2: Attaching device shall be p

7、rong and wing-grip clutch type with two prongs. Each prong shall have an overall length of 5/16 inch + 1/8 inch - 0 and be either fused or hard soldered to the badge. The prongs shall be located along either the horizontal or vertical center lines. The prongs shall be positioned at least 1/16 inch +

8、 0 - 1/32 inch from the edge of the badge and shall be 15/32 inch + 1/16 inch - 0 apart. NOTES: 1. The term (REF) refers to the measurements taken from the Government furnished obverse hub or die. 2. The manufacturer may deviate from MIL-DTL-3628 by using nickel underplating prior to plating with 24

9、K gold. Custodians: Preparing activity: Army - IH Army - IH Navy - NU Review Activity: (Project No. 8455-2013-132) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-