ARMY MIL-C-14637 A-1982 CASE FLAG INTERMENT《葬礼用旗箱》.pdf

《ARMY MIL-C-14637 A-1982 CASE FLAG INTERMENT《葬礼用旗箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-14637 A-1982 CASE FLAG INTERMENT《葬礼用旗箱》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-14b37A 84 9979906 0378936 O 1 September 1982 Superseding MIL-C-0014637 (IH) 1 August 1982 MIL-C-9828A( USAF) 13 August 1963 MILITARY SPECIFICATION CASE, FLAG, INTERMENT 1. SCOPE 1.1 interment flag . This specification covers one type of plastic flag case for use with the 2. APPLICABLE DOCUMENT

2、S 2.1 on the date of invitation for bids or request for proposal. form a part of this specification to the extent specified herein. SPECIFICATIONS The followingspecifications, standards and drawings of the issue in effect FEDERAL L-P-375 - Plastic Film, Flexible, Vinyl Chloride . PPP-B-621 - Boxes W

3、ood, Nailed and Locked-Corner PPP-B-636 - Box, Shipping, Fiberboard PPP-B-676 - Boxes, Setup MILITARY MIL-F-10884 - Fasteners, Snap STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage DRAWINGS FSC 8345 Provided b

4、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14b37A 84 7999906 0378737 2 MIL-C-14637A THE INSTITUTE OF HERALDRY 5-1-451 - Case, Flag, Interment (Copies of specifications, standards and drawings required by the contractors in connection with specific p

5、rocurement functions should be obtained from the procuring activity or as directed by the contracting officer.) (Figure 1 is a miniature copy of the reference drawing and is attached for information only). 3. REQUIREMENTS 3.1 First article samples. purchase order (see 6.2), before production is comm

6、enced three completely fabricated cases shall be submitted or made available to the contracting officer or his authorized representative for inspection and tests as specified in 4.2. The approval of the first article authorizes the commencement of production but does not relieve the contractor of th

7、e responsibility for compliance with all provisions of this specification. The first articles will be manufactured in the same facilities to be used for the manufacture of the production items. 3.2 Material. The material shall conform to the referenced specifications and the requirements specified h

8、erein. 3.2.1 Vinyl film. The film for the case shall be a colorless, flexible vinyl film conforming to type I, class 1 of L-P-375, except the resistance to accelerated weathering exposure shall be 40 hours and the requirement for the following characteristics shall not apply: stiffness, extraction i

9、n soapy water, volatility and lacquer lifting. finish on both faces and shall be 0.012 - + .O01 inch thick. Unless otherwise specified in the contract or The vinyl film shall have a dull matte 3.2.1.1 Reinforcement patches. The vinyl film for the reinforcement patches shall be as specified in 3.2.1,

10、 except the thickness shall be 0.020, - + .004, - .O02 inch. 3.2.2 Snap fastener. The snap fastener shall be a soft action type conforming to style 2, finish 3, line 20 of MIL-F-10884. 3.3. Construction. The flag cases shall conform to the details and dimensions shown on drawing 5-1-451 and the requ

11、irements specified herein. 3.3.1 -Case. front and back panels shall be heat seaie (flat seam) along two sides with a 3/8 + 1/16 inch wide heat seal set in 1/4 inch from the edge, or the front and back-panels may be heat sealed along two sides with a 1/8 inch minimum width heat seal with or without a

12、 rolled edge. The top of the back panel shall be folded upon itself to the inside with the cut edge turned under not less than 1/16 inch to form a hem and heat sealed. The finished width of the heat seal shall be 13/16 1/8 inch. The case shall be fabricated from vinyl specified in 3.2.1 and the - 2

13、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-14b37A 84 M 7779706 0378738 4 - . MIL-C-14637A 3.3.2 Reinforcement. reinforced with a 1 + 1/8 inch wide piece of vinyl film as specified in 3.2.1 and shall be heat sealed. square shall be heat sea

14、led at the locations of both the male and female portions of the snap fastener. Both these reinforcement patches shall be heat sealed to the inside of the panels with a smooth surface on all edges and with sufficient thickness to inhibit detachent of snap fastener. The entire inside edge of the fron

15、t panel shall be In addition, a reinforcement patch 1 + 1/8 inch 3.3.3 Snap fastener. the drawing. reinforcement pieces, with the stud and eyelet on the back panel and the button and socket on the front panel flap. The snap fastener parts shall be positioned as shown in The snap fastener shall be at

16、tached through the heat sealed , 3.3.4 Workmanship. acceptable quality level established by this specification. 3.3.5 Label. be inserted in each plastic flag case. informat ion: The cases shall be clean, well made, and shall be the A white paper identficatian label, approximately 2“ x 4“ shall The l

17、abel shall contain the following STOCK NUMBER NOMENCLATURE CONTRACT NUMBER 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or order, the supplier is responsible for the performance of all inspection requirements as specified herein. Excep

18、t as otherwise specified in the contract or purchase order, the supplier may use his own or any other facilities suitable for the performance of inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set for

19、th in the specification where such inspections are deemed necessary to assure supplies and services conorm to prescribed requirements. 4.2 First article inspection. When a first article is required, inspection and testing of the first article shall be made on three completely finished cases for all

20、provisions applicable to end product examination and tests. 4.3 Inspection for acceptance. Unless otherwise indicated, inspection shall be in accordance with MIL-STD-105. 4.3.1 Certification of compliance. contractors certification of compliance that it meets the requirements of 3.2.2. 4.3.2 End ite

21、m examination. classified in accordance with 4.3.2.1 and 4.3.2.2. in accordance with 4.3.2.3. completely fabricated case. The snap fastener may be accepted on the Defects found during the examination shall be The lots shall be inspected The sample unit for these examinations shall be one 4.3.2.1 Exa

22、mination for visual characteristics. Defects designated by an asterisk (*) shall be classified as major when they seriously affect appearance or serviceability and minor when they affect appearance or serviceability, but not seriously. Provided by IHSNot for ResaleNo reproduction or networking permi

23、tted without license from IHS-,-,- Y- MIL-C-L4637A 84 m 977770b 0378737 b m MIL-C-14637A Examine Defect Major (*I Minor - . - Quality of plastic Not type specified X mat er i al Snap fastener Not uniformly colorless or not clear Finish not smooth dull matte on both sides. Tear, cut, hole, crack or b

24、reak. Deep gouge orascratch.,. Scuff, crease, blister, bub- ble, pimple, or pit. Any dirt, oil, foreign matter, spot, stain or other discoloration which requires a cleaning agent for removal Objectionable odor Missingrloose, mismated or otherwise defective Improperly clinched result- ing in cutting

25、of the vinyl film. Any sharp burrs or metal slivers which may affect serviceability- Stud not aligned with the socket causing a noticeable bulge or twist on the flap when snapped. Improperly finished. Insecurely clinched, X X X X X X - 4 , e I - - . - ., Provided by IHSNot for ResaleNo reproduction

26、or networking permitted without license from IHS-,-,-MIL-C-14637A 4 m 9777706 0378740 2 W MIL-C-14637A Examine Defect Major (* Minor Workmanship and Open seam.e. X assembly - Heat seal not as specified. Seal not in proper loca- - ti on. Any area of seal not contin- uous (or thin) resulting in weak o

27、r incomplete juncture - Heat seal ends torn, rough, or not trimmed more than 1/16 inch Poor heat seal, resulting in inadequate fusion. . Width of heat seal along sides, not as specified. Heat seal not set in from edge as specified Snap fastener missing Snap fastener has sharp or rough edge which may

28、 damage the case or tau- injury in handling. Snap fastener has defective component, failing to serve intended purpose. Not reinforced as speci- fied. Re infor ceme nt imp 1: op eriy locatedcc Any patt missing or mis- placed.-Co.c Any part not attached or as- sembled as specified. X 5 Provided by IHS

29、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14b37A 84 m 7777906 03787q1 4 m MIL-C-14637A m 4.3.2.2 Dimensional examination of case, flag interment. Any dimension that is not within the specified tolerance shall be classified as a defect, 4.3.2.3 AQLs and

30、inspections levels. The inspection levels and acceptable quality levels (AQLs) expressed in defects per hundred units, shall be as follows : Inspection AQL 1 eve1 Major Total For defects applicable to 4.3.2.1 II 2.5 10. o For defects applicable to 4.3.2.2 5-3 One class 4. O 4.3.4 Examination of prep

31、aration for delivery requirements. An examination shall be made to determine that packaging, packing, and marking requirements of section 5 of this specification are complied with. Defects shall be scored in accordance with the list below. fully prepared for delivery with the exception that it need

32、not be sealed. Defects for closure listed below shall be examined on shipping containers fully prepared for delivery. The lot size shall be the number of shipping containers in the end item inspection lot. shall be 2,5 defects per hundred units. The sample unit shall be one shipping container The in

33、spection level shall be S-2 and the AQL Exami ne Defects Marking (exterior and interior) Ma ter iala Wo rkma 118 hip Content Omitted, incorrect, illegible, or im- proper size, location, sequence or method of application. Any component missing. Any component damaged, affecting serviceability . Inadeq

34、uate application of components , such as incomplete closure of case liners, container flaps, loose strapping. Number of intermediate containers is more or less than required. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Packaging shall be level A or C, as specified (see 6.2). 5.1.1. Level A. inches by

35、 12 inches by folding in the corners of the triangle. Ten of the folded cases shall be packaged flat in a Set-up paperboard box conorming to type I, variety 1, class A, style 1 of PPP-B-676. Box closure shall be in accordance with the appendix of the container specification. Brand box closing filame

36、nt tape No. 898 or equal, l/!“, using a minimum of two 1/2“ x 4“ (“LI Clips) on each edge, may be utilized as an alternate method for effecting closure of setup boxes. Flag case shall be folded into a rectangle approximately 10 The use of Scotch 6 i Provided by IHSNot for ResaleNo reproduction or ne

37、tworking permitted without license from IHS-,-,-MIL-C-14h37A BLJ W 7777906 0378742 h W MIL-C-1463 7A 5.1.2 Level C. Flag cases shall be packaged to afford adequate protection againstcleterioration and damage during shipment from the supply source to the first receiving activity. The supplier may use

38、 his standard practice when it meets these requirements. 5.2 Packing. Packing shall be level A, B or C as specified (see 6.2). 5.2.1 Level A, Cases packaged as specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to class weather resistant, type V3c or V3s of

39、PPP-B-636. Closure shall be in accordance with the appendix of the applicable container specification. 5.2.2 Level B. Flag cases packaged as specified in 5.1, shall be packed in a snug-fitting fiberboard shipping container conforming to class Domestic, grade 275 of PPP-B-636. container specification

40、. the weight and size limitation of the container specification. 5.2.3 Level C. Flag cases, packaged as specified in 5.1, shall be packed in a manner to insure carrier acceptance and safe delivery at destination at the lowest transportation rates for such supplies. accordance with the rules and regu

41、lations of carriers applicable to the mode of transportation. Closure shall be in accordance with the appendix of the The weight in each shipping container shall not exceed Containers shall be in 5.3 Marking. purahase order, intermediate packages and shipping containers shail be marked in accordance

42、 with MIL-STD-129, In addition to any special marking required by the contract or 6. NOTE3 6.1 Intended uBe. to contain the folded interment flag which is presented to the next of kin. 6.2 Ordering data. Procurement documents should specify the following: Cases covered by this specification are inte

43、nded to be used a. Title, number, and date of this specification. b. C. When a first article sample is not required (see 3.1). Applicable levels of packaging and packing (see 5.1 and 5.2). Q CUSTODIANS: Army - IH Air Force - 11 Navy - NU REVIEW ACTIVITIES: Navy - NU, MC Air Force - 99 DLA - CT USER

44、ACTIVITIES: Air Force - 45 Navy - CG Project No. 8345-0117 PREPARING ACTIVITY: The Institute of Heraldry, United States Army Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14637A O 1 U 4 m I - .WIL-C-L4637A 4 m 7799906 0378943 8 M - I T FIGURE 1 f Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-