ARMY MIL-A-49273-1988 AMPLIFIER POWER SUPPLY AM-7152 GRC-213 AND ADAPTER KIT VEHICLE MK-2154 GRC-213《AM-7152 GRC-213能源供应增强器及MK-2154 GRC-213载体成套附件》.pdf

《ARMY MIL-A-49273-1988 AMPLIFIER POWER SUPPLY AM-7152 GRC-213 AND ADAPTER KIT VEHICLE MK-2154 GRC-213《AM-7152 GRC-213能源供应增强器及MK-2154 GRC-213载体成套附件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-A-49273-1988 AMPLIFIER POWER SUPPLY AM-7152 GRC-213 AND ADAPTER KIT VEHICLE MK-2154 GRC-213《AM-7152 GRC-213能源供应增强器及MK-2154 GRC-213载体成套附件》.pdf（41页珍藏版）》请在麦多课文档分享上搜索。

1、NIL-A-49273(CR) 26 January 1988 MILITARY SPECIFICATION AMPLIFIER, POWER SUPPLY AM-7152/GRC-313 ANJJ ADAPTER KIT, VEHICLE MK-2154/GRC-213 This specification is approved for use within the Communications- Electronics Command, Department of the Army, and is available for use by all Departments and Agen

2、cies of the Department of Defense. Y* 1. SCOPE - 1.1 Scope. This specification establishes the requirements for manufacture and acceptance of the Amplifier, Power Supply AM-7152/GRC-213 and Adapter Kit, Vehicle MK-2154/GRC-213 which together are used for vehicular operation of the AN/PRC-104 Radio S

3、et (Reference to AN/PRC-104 also includes .LVIPRC-l04A, AN/PRC-l04(V) and AN/PRC-l04B(V). Performance specifications of the AN/PRC-104 are provided inspecification MIL-R-29418 (MC). This equipment allows operation of the AN/PRC-104 in a moving wheeled or tracked vehicle, using the nominal 28 volt ve

4、hicular supply. The amplifier-power supply also provides operation of the AN/PRC-104 with a vehicular intercommunication system (AN/VIC-l(V), a squelched one-watt audio drive for a loudspeaker LS-454, and antenna conditioning for a 15 foot whip antenna (base AB-657B, three each sections MS-116, and

5、one each of sections MS-117 and MS-118). z 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications, standards and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. these documents shall be those listed in

6、 the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. Unless otherwise specified, the issues of Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this

7、 document should be addressed to Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN: AMSEL-ED-TO, Fort Monmouth, New Jersey 07703-9990 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by lette

8、r. AMSC: N/A FSC 5820 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. a Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL PP

9、P-B-636 MILITARY MIL-C-22750 MIL-(2-46168 MIL-(2-55442 MIL-E-16400 MIL-E-55585 MIL-F-14072 MIL-L-12632 MIL-P-116 MIL-P-11268 .I I L-P - 2 3 3 7 7 MIL-Q-9858 NIL-R-29418 MIL-S-901 STANDARDS 241 LITARY MIL-STD-105 Boxes, Shipping, Fiberboard Coating, Epoxy-Polymide Coating, Aliphatic Polyurethane, Che

10、mical Agent Resistant. Cable Assemblies and Cord Assemblies, Packaging of Electronic, Interior Communication and Navigation Equipment, Naval Ship and Shore, General Specification for .E pr Electronic Equipment and Parts, Packaging of Finishes for Ground Electronic Equipment Loudspeaker, Permanent Ma

11、gnet (Encased, 2 Watt, Fungus, Gunblast, and Immersion Resistant), General Specification for Preservation, Methods of Parts, Materials and Processes in Electronic Equipment Primer Coating: Epoxymide, Chemical and Solvent Resistant Quality Program Requirements Military Specification Radio Set: AN/PRC

12、-I04(V) Shock Tests, High-Impact Shipboard Machinery, Equipment and Systems, Requirements for Sampling Procedure and Tables for Inspection by Attributes 2 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted witho

13、ut license from IHS-,-,-1: MIL-A-47273 58 m 7777906 0362752 3 m ?!I L-STD- 1 O 9 MIL-STD-252 NIL-STD-454 NIL-STD-470 MIL-STD-471 NIL-STD-726 MIL-STD-781 MIL-STD-810 Quality Assurance, Terms and Definitions Classification of Visual and Mechanical Defects for Equipment, Electronics, Wired and other De

14、vices Standard General Requirements for Electronic Equipment Maintainability Program Requirements (For Systems and Equipments) Maintainability Demonstration Packaging Requirements Codes Reliability Tests, Exponential Dis tribut ion Znvironmental Test Methods MIL-STD-831 Test Reports, Preparation of

15、MIL-STD-1275 Electrical Circuit, 28 Volt Transient Characteristics for Military Radios MIL-STD-2073-2 Packaging Requirement Codes HANDBOOKS MIL-HDBK-472 Maintainability Predictions 2.1.2 Other government documents and drawings. The following other Government documents and drawings form a part of thi

16、s specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAWINGS U.S. Marine Corps. 755002B9017 7 5 500 2B 90 18 755002B9019 755002B9100 U.S. Army A30 23140 A30 23 150 Cable Assembly, Power, Electrical Cable Ass

17、embly, Special Purpose, Electrical Cable Assembly, Radio Frequency Amplifier, Power Supply AM-7152/GRC-213 Installation Control Drawing Mounting Base, Electrical MT-6234/GRC-213 3 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or n

18、etworking permitted without license from IHS-,-,-MIL-A-97273 58 M 9777706 OIE453 5 A30 23 160 Antenna Switching Unit, SA-2365/GRC-2?3 A3023 313 Cable Assembly, Radio Frequency SM-D-415550 Cable Assembly, Power, Electrical SM-D-415551 Cable Assembly, Power, Electrical SM-D-415553 . Cable Assembly, Sp

19、ecial Purpose, Electrical DOCUMENTS SEL FORM 1183 Systems Safety Design Verification Checklist (Copies of Specifications, standards, handbooks, drawings and other government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting ac

20、tivity or as directed by the contracting activity.) 2.2 Order of precedence. In the event of a conflict betwean the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall tak

21、e precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained 3. REQUIREMENTS 3.1 Item definition. The Amplifier, Power supply AM-7152/GRC-213 (herein also called amplifier-power supply) and the Adapter Kit, Vehicl

22、e MK-2154/GRC-213 (herein also called vehicular adaptor) shall interface with the AV/PRC-104 Radio Set, the AN/VIC-1(V) Intercommunication Set, and Radio Sets AN/VRC-43, 44, 46, 53, and 64. The amplifier-power supply shall also provide loudspeaker output with adjustable squelch. Power lines and inte

23、rface lines shall have EM1 filtering and conditioning to protect interfacing units from transients and RFI. The intended use includes, but is not limited to, N151A2 utility jeep, M561 (Gamma Goat) truck, M113 and 3577 Armored Personnel Carrier in all types of weather and terrain which dictates the e

24、nvironmental requiremenLs specified herein. The vehicular adapter shall consist of Switching Unit, Antenna SA-2365/GRC-213 (herein also called antenna switching unit) and Mounting Base, Electrical Equipment MT-6234/GRC-213 (herein also called mounting base). The antenna switching unit shall permit s

25、witchable selection of whip or dipole atl.tenna, and selection of necessary antenna loading elements. The mounting base shall reduce shock and vibration levels to the AN/PRC-104 sufficiently such that no degradation of performance of the AN/PRC-104 shall result. The AN/PRC-104, herein referred to as

26、 PRC-104, shall consist as a minimum of Receiver- Transmitter RT-l209/URC (herein also called receiver-transmitter) and Radio Frequency Amplifier AM-6874/PRC-104. The combination of the amplifier-power supply and the vehicular adapter (without the AN/PRC-104 4 Copyright Communications - Electronics

27、Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-ti9273 58 9Oh OLb295ti 7 , I I I l I 1 t I I t I ! NIL-A-49 2 7 3 (CR unless otherwise specified) is herein also referred to as equipment. The combination of the ve

28、hicular adapter and appropriate cables and bolts constitutes an installation kit. 3.1.1 First article. When specified in the contract or purchase order, and prior to submission of any complete production items for acceptance, the contractor shall furnish first articles for determination of conforman

29、ce to this specification. Examination and tests shall be those specified herein. Approval of the first articles by the procuring activity shall not relieve the contractor of his obligation to supply vehicular adapters conforming to this specification. Any changes or deviations of the production item

30、s from the first articles shall be subject to the approval of the contracting officer . 3.1.2 Interface and cable definition. 3.1.2.1 Amplifier-power supply to receiver-transmitter interface. A removable/replaceable jumper cable (USMC P/N 755002B9018 or equivalent), shall mate physically and electri

31、cally with the 5 pin audio connector on the receiver-transmitter and with the 6 pin audio connector on the amplifier-power supply. This cable is supplied with the equipment. This interface is defined in Table III. 3.1.2.2 Amplifier-power supply to AM-h874/PRC-104. A removable/ replaceable jumper cab

32、le (USMC P/N 755002B9019) shall mate physically and electrically with the DC power connector Pl of the AM-6874/PRC-104 and the radio power output connector 5104 of the Amplifier-Power supply. This cable is supplied with the equipment. This interface is defined in Table IV. 3.1.2.3 Amplifier-power su

33、pply to primary input Jower supply. Interface between the primary input power supply and the 4-pin connector JI01 on the amplifier-power supply shall be made with power cable CX-4720 (U.S. Army drawing number SM-D-415550) or equivalent, and is part of the installation kit. 3.1.2.4 Amplifier-power su

34、oply to auxiliary output power. Primary output power (unprotected) interface from the 4-pin power connector J103 on the amplifier-power supply to Radio Sets AN/VRC-43, 46, 53 and 64 shall be made with power cable CX-4721 (U.S. Army drawing number SM-D-415551) or equivalent, and is part of the instal

35、lation kit. 3.1.2.5 Amplifier-power supply to VIC-l(V) intercommunication system. Female receptacle 5102 shall provide interface to the AM-1780 of the VIC-l(V) vehicular intercommunication system by means of a CX-4723 cable (U.S. Army drawing number SM-D-415553) or equivalent, and is part of the ins

36、tallation kit. This interface is defined in Table V. 3.1.2.6 Amplifier-power supply to loudspeaker LS-454/U or H-250/ Handset. Audio receptable J1 provides interface to Loudspeaker LS-454/U or Handset H-250/U. This interface is defined in Table VI. I. I 5 Copyright Communications - Electronics Comma

37、nd Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-97273 58 9779706 0162955 7 W 3.1.2.7 Power amplifier-coupler AM-6874 to antenna switching unit SA-2365, A removable/replaceable 50 ohms RF cable (USMC P/N 755002B9017) w

38、ith male BNC connectors on both ends shall mate with J1 on AM-6874 amplifier coupler and J201 on the antenna conditioner. This cable is supplied with the equipment. 3.1.2.8 Antenna switching unit 58-2365 to antenna base AB-652B. A special purpose RG-114 cable with male N type connectors on each and

39、(U.S. Army drawing number A3023313) shall mate with 5202 on the Antenna Switching Unit and AB-652B antenna base. This cable is part of the installation kit. 3.1.2.9 Antenna switching unit SA-2365 to dipole type antenna. A BNC female connector at the rear of the antenna conditioner 5203 shall provide

40、 connection to a dipole type antenna. The appropriate cable is supplied with the AN/PRC-l04A as part of its antenna kit. 3.2 performance. 3.2.1 Amplifier-power supply. The amplifier-power supply shall meet the requirements herei- when operated from a voltage source of 24.5 to 32 VDC that meets the r

41、equirements of MIL-STD-1275. In addition, the amplifier-power supply shall allow the AN/PRC-104 to operate without degradation of its specified performance when the input power source meets the requirements of MIL-STD-1275 for normal operation. 3.2.1.1 Power supply. 3.2.1.1.1 Input power. When opera

42、ted with supply voltage of 26.5 VDC and with an AN/PRC-104 installed, the input power shall not exceed 200 watts in any mode of operation. 3.2.1.1.2 Reversed polarity. The amplifier-power supply unit and associated receiver-transmitter shall be protected from reversed polarity primary input power. B

43、lowing of a fuse or circuit breaker trip is allowed for this protection. The chassis shall be negative. 3.2.1.1.3 Protected power output. The amplifier-power supply shall provide the AN/PRC-104 with a nominal 100 watts of protected power in compliance with MIL-STD-1275., 3.2.1.1.4 Single fault prote

44、ction. The amplifier-power supply shall protect the AN/PRC-104 from damage when the power source has a single fault as defined by MIL-STD-1275. 3.2.1.1.5 Transient protection. The amplifier-power supply shall not permit a positive transient at the input to the AN/PRC-104 to exceed 42V when the power

45、 source meets the requirements of MIL-STD-1275. 3.2.1.1.6 Maximum protected output current. The amplifier-power supply shall be capable of providing the AN/PRC-104 with up to 5.5 amperes of protected DC current. 6 1 1 *I 1 I I 1 i i Copyright Communications - Electronics Command Provided by IHS unde

46、r license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-Ll7273 58 m 9777906 0362756 O m I l I I I I I I t I I i I I I 3.2.1.1.7 Overload protection. Yith short circuit at the protected output power connector no damage to transistor or devices other

47、 than an open fuse or circuit breaker trip shall result. 3.2.1.1.8 Auxiliary power output. The amplifier-power supply shall provide unprotected primary power to the auxiliary connector which shall drain a maximum current of 10 amps. This output shall be connected in parallel to the input supply line

48、 from the vehicle battery. 3.2.1.2 Loudspeaker amplifier. 3.2.1.2.1 Loudspeaker. The loudspeaker shall be a 2 watt, permanent magnet, type LS-454/U, resistant to fungus, gunblast and immersion, per XIL-L-12632. 3.2.1.2.2 Speaker on/off control. An on/off switch shall be provided to turn the speaker

49、on and off. 3.2.1.2.3 Volume control. The control of the headphone output, the speaker output, and the monitor output to the AN/VIC-1(V) Intercommunicacion Set, shall be provided by the audio volume control of the AN/PRC-104 radio. 3.2.1.2.4 Audio amplifier input. AF input, from the receiver- transmitter, RT-1209, shall be a minimum of 2 mW into 500 ohms. Distortion of the RT output shall be 5 percent maximum. The loudspeaker volume is controlled by the RT volu