ARMY A-A-59800 A-2011 SOLIDS ALIPHATIC POLYUREA COATING.pdf

《ARMY A-A-59800 A-2011 SOLIDS ALIPHATIC POLYUREA COATING.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-59800 A-2011 SOLIDS ALIPHATIC POLYUREA COATING.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 Comments, suggestions, or questions on this document should be addressed to U.S. Army RDECOM, Tank Automotive Research, Development and Engineering Center, ATTN: RDTA-EN/STND/TRANS MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Since contact i

2、nformation can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.daps.dla.mil. AMSC N/A FSC 8010 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59800A (AT) August 30, 2011 SUPERS

3、EDING A-A-59800 (AT) September 11, 2007 COMMERCIAL ITEM DESCRIPTION SOLIDS ALIPHATIC POLYUREA COATING The General Services Administration has authorized the use of this Commercial Item Description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a range of 100% solid

4、s, two-component aliphatic polyurea coatings intended for use on cleaned, pretreated and primed (when required) substrates which include: steel, galvanized steel, aluminum, plastic, composites, wood, fabric and concrete. These UV-durable polyurea coatings are intended to provide extremely tough dura

5、ble coatings that are impact resistant, stone and gravel chip resistant, abrasion resistant, chemical resistant, corrosion resistant and sound and vibration damping over a wide temperature range. These aliphatic polyurea coatings contain no hazardous diphenyl methane diisocyanate (MDI) or toluene di

6、isocyanate (TDI) species and no volatile organic compounds. These coatings can be applied using a variety of application equipment including high-pressure heated spray via plural component spray equipment and low-pressure heated spray via static mix cartridges. The coatings can be repaired using sma

7、ll volume repair kits. The Type II coating can also be applied at room temperature using unheated low-pressure static mix cartridges, at material temperatures as low as 60oF. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59800A 2 2. CLASSIFICAT

8、ION. The Corrosion Prevention Compounds (CPCs) shall conform to the following types: 2.1 Type Type I - Improved General Purpose Coating. Type II - Coating Optimized for Blast Resistance. Type III - Coating Optimized for Fire Resistance. 2.1.1 Type I: Improved General Purpose Coating. Type I coating

9、has outstanding abrasion, impact, scratch and 29CFR1910.1200 requires that the MSDS for each hazardous chemical used in an operation must be readily available to personnel using the material. Contracting officers will identify the activities requiring copies of the MSDS. 7.3 Ordering data. The contr

10、act or order should specify the following: a. CID document number and revision. b. Product conformance provisions. c. Packing requirements 7.4 Key words. Abrasion protection Corrosion protection Corrosion resistance Impact protection Chip resistant Sound damping Vibration damping UV durable Tough Sp

11、all resistance Flame resistance Damage protection Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59800A 9 Custodian: Preparing Activity: Army - AT Army AT (Project Number 8010-2011-017) NOTE: The activities listed above were interested in this d

12、ocument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online, database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-