ANSI UL 218-2015 UL Standard for Safety Fire Pump Controllers (Third Edition).pdf

《ANSI UL 218-2015 UL Standard for Safety Fire Pump Controllers (Third Edition).pdf》由会员分享，可在线阅读，更多相关《ANSI UL 218-2015 UL Standard for Safety Fire Pump Controllers (Third Edition).pdf（104页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 218 Fire Pump ControllersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUC

2、TION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Fire Pump Controllers, UL 218 Third Edition, Dated September 16, 2015 Summary of Topics This new edition of UL 218 adopts the following revisions: 1. Correlating UL 218 with the 2013 Edition of NFPA 20. 2. Revise the denition

3、s in UL 218 to correlate with the denitions in the National Electrical Code (NFPA 70). 3. Revising the requirements covering service equipment markings to include a reference to NEC Article 230. 4. Revising 6.9.1 to change the term line voltages to phase-to-phase voltages. 5. Addition of interconnec

4、tion diagrams for re pump controllers and diesel engines to correlate with recent revisions to UL 1247. 6. Revising to the requirements covering diesel engine re pump controllers relative to controllers in the automatic mode, where an operator can crank and start the engine manually at the controlle

5、r without cooling loop water being provided automatically through the engine. 7. Add “Symmetrical rms amperes” as a footnote to Table 10 similar to footnote “a” in Table 6. 8. Requirements that are being proposed to be revised include the construction requirements, dielectric voltage withstand test,

6、 disconnecting means, diesel engine drive controllers, dump valves, variable speed re pump controllers, markings, the deletion of requirements covering the limited service controllers for electric motor driven re pumps, and the addition of Section 17, Routine Tests. 9. Revising the requirements cont

7、ained in Subsection 9.1, General, of Section 9, Residential Fire Pump Controllers. 10. Aligning the standard with NFPA 20. 11. Adding the term .for Use in One- and Two-Family Dwellings in item (c) of 16.3. As noted in the Commitment for Amendments statement located on the back side of the title page

8、, UL, CSA, and ANCE are committed to updating this harmonized standard jointly. The new and/or revised requirements are substantially in accordance with Proposal(s) on this subject dated May 16, 2014, December 5, 2014, December 6, 2014, and July 3, 2015. All rights reserved. No part of this publicat

9、ion may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. SEPTEMBER 16, 2015 UL 218 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITH

10、OUT PERMISSION FROM UL UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or si

11、milar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage e

12、ver exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fe

13、es) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. SEPTEMBER 16, 2015 UL 218 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Association of Standardiza

14、tion and Certication NMX-J-626-ANCE-2015 Second Edition CSA Group CSA C22.2 No. 263-15 Second Edition Underwriters Laboratories Inc. UL 218 Third Edition Fire Pump Controllers September 16, 2015 ANSI/UL 218-2015 Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTI

15、ON WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Association of Standardization and Certication (ANCE), the Canadian Standards Association (operating as “CSA Group”), and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any par

16、t of the standard may be submitted to ANCE, CSA Group, or UL at anytime. Revisions to this standard will be made only after processing according to the standards development procedures of ANCE, CSA Group, and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or rev

17、ised or additional pages bearing their date of issue. ANCE will incorporate the same revisions into a new edition of the standard bearing the same date of issue as the CSA Group and UL pages. Copyright 2015 Rights reserved in favor of ANCE. ISBN 978-1-77139-927-2 2015 CSA Group All rights reserved.

18、No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to periodic review, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the followi

19、ng information to inquirescsagroup.org and include Proposal for change in the subject line: Standard designation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Gro

20、ups Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2015 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, o

21、wnerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the Third Edition. The most recent designation of ANSI/UL 218 as an American National Standard (ANSI) occurred on September 16, 2015. ANSI approval for a s

22、tandard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Preface. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to

23、UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR D

24、ISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .6 INTRODUCTION 1 Scope .8 1.1 Products covered .8 1.2 Products not covered .8 2 Normative References .8 3 Units of Measurement .9 4 General Requirements .9 4.1 General .9 4.2 Components .9 5 Denitions 9 CONSTRUCTION 6 Construction .11 6.1 Encl

25、osures .11 6.2 Spacings .12 6.3 Insulating barriers .12 6.4 Field wiring terminals 13 6.5 Grounding 14 6.6 Service equipment .15 6.7 Wire bending space .16 6.8 Internal wiring, busbars, and connections .16 6.9 Provisions for use of test instruments 18 6.10 Control circuit 18 6.11 Auxiliary circuits

26、18 6.12 Manual controls 18 6.13 Surge arresters 19 6.14 Isolating switch .19 6.15 Circuit breaker disconnecting means 20 6.16 Locked rotor overcurrent protection .21 6.17 Motor starting means .21 6.18 Use of sensing devices .23 6.19 Provision for alarm and signal devices 24 6.20 Automatic controller

27、s .25 6.21 Non-automatic controllers .28 6.22 Stopping methods 29 6.23 Power interruption 29 6.24 Ground fault and arc fault protection 29 PERFORMANCE 7 Performance Tests .29 7.1 Short circuit test general 29 7.2 Short circuit test standard fault currents 31 7.3 Short circuit test high fault current

28、s 31 7.4 Dielectric voltage-withstand test .31 7.5 Wire exing test .32 SEPTEMBER 16, 2015 NMX-J-626-ANCE-2015 CSA C22.2 NO. 263-15 UL 218 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7.6 Phase loss detection test .32 7.7 Pressure switch/

29、transducer tests 32 7.8 Locked rotor overcurrent protection test 34 7.9 Barrier dielectric strength test .35 7.10 Temperature test .36 7.11 Dielectric voltage withstand test (after normal operating temperature) .40 7.12 Coated printed circuit board performance test 41 7.13 Test for controllers with

30、single-phase start protection .44 7.14 Preshipment .44 7.15 Controller functionality tests .45 7.16 Emergency run mechanism 45 7.17 EMC requirements .45 8 Limited Service Controllers For Electric Motor Driven Fire Pumps 45 8.1 General 45 9 Residential Fire Pump Controllers 45 9.1 General 45 9.2 Visi

31、ble indicators 47 9.3 Marking 47 10 Medium Voltage Fire Pump Controllers (Rated Over 600 V) .47 10.1 General .47 10.2 Meters 47 10.3 Isolation switch .48 10.4 Pressure-activated device .48 10.5 Control circuits .48 10.6 Visible indicators .48 10.7 Disconnecting means 48 10.8 Emergency run mechanical

32、 control at controller 49 10.9 Locked rotor overcurrent protection .49 10.10 Performance 49 10.11 Ratings 49 10.12 Markings .49 11 Controllers With Automatic Transfer Switches For Electric Driven Fire Pumps (600 V Maximum) .49 11.1 General .49 11.2 Isolating switch 50 11.3 Circuit breaker .50 11.4 S

33、ensing and signal devices 50 11.5 Transfer between sources 51 11.6 Test switch .52 11.7 Ratings .52 12 Diesel Engine Drive Controllers .52 12.1 General .52 12.2 Locked enclosure 52 12.3 Field wiring terminals .53 12.4 Starting and control .53 12.5 Alarm and signal devices .54 12.6 Auxiliary contacts

34、 for remote sensors .56 12.7 Pressure recorder 57 12.8 Weekly program timer 57 12.9 Automatic controllers .57 12.10 Non-automatic controller .59 12.11 Methods of stopping .59 12.12 Emergency control 60 SEPTEMBER 16, 2015 NMX-J-626-ANCE-2015 CSA C22.2 NO. 263-15 UL 218 4UL COPYRIGHTED MATERIAL NOT AU

35、THORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 13 Controllers For Additive Pumps .60 13.1 General .60 13.2 Automatic starting 60 13.3 Dump valves .60 13.4 Methods of stopping 61 13.5 Manual operation .61 13.6 Lockout .61 14 Variable Speed Fire Pump Controllers .61 14.1

36、General .61 14.2 Environmental .62 14.3 Power components .63 14.4 Control equipment and components 64 14.5 Mode control 65 14.6 Motor control 66 14.7 Signals and alarms .66 14.8 Skip frequencies .66 14.9 Variable mode operation 66 14.10 Automatic transfer to bypass operation 67 14.11 Marking 67 RATI

37、NG 15 Ratings 67 MARKING 16 Markings .68 Routine Tests 17 Routine Tests 71 TABLES AND FIGURES Annex A References (Normative) Annex B Standards for components (normative) B.1 Component Standards 95 Annex C French and Spanish Translations and Markings (informative) C.1 Markings French and Spanish Tran

38、slations 99 Annex D Test Samples (informative) SEPTEMBER 16, 2015 NMX-J-626-ANCE-2015 CSA C22.2 NO. 263-15 UL 218 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized ANCE, CSA Group, and UL standard for re pump co

39、ntrollers. It is the second edition of NMX-J-626-ANCE, the second edition of CSA C22.2 No. 263, and the third edition of UL 218. This edition of NMX-J-626-ANCE supersedes the previous edition published on September 28, 2009. This edition of CSA C22.2 No. 263 supersedes the previous edition published

40、 in 2009. This edition of UL 218 supersedes the previous edition published in 1999. This harmonized standard was prepared by the Association of Standardization and Certication, (ANCE), CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Technical Harmonization Committee

41、 for Fire Pump Controllers, CANENA THSC 17B WG4, of the Council on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. The

42、 present Mexican Standard was developed by the CT 64 Instalaciones elctricas y proteccin contra choque elctrico from the Comite de Normalizacion de la Asociacion de Normalizacion y Certicacion, A.C., CONANCE, with the collaboration of the re pump controllers manufactures and users. This standard was

43、 reviewed by the CSA Subcommittee for Fire Pump Controllers, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard was r

44、eviewed and approved by the Committee de Normalizacion of ANCE (CONANCE). This standard was reviewed by ULs Standards Technical Panel (STP) for Fire Pump Controllers, STP 218. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Applic

45、ation of standard A UL standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice that accompanies the latest set of revised requirements. Where reference is made to a specic number of samples to be tested, the specied number

46、is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. Level of harmonization This

47、standard uses the IEC format but is not based on, nor shall it be considered equivalent to, an IEC standard. This standard is published as an equivalent standard for ANCE, CSA, and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Techni

48、cal national differences are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protecti

49、on that the country considers appropriate. Presentation is word for word except for editorial changes. SEPTEMBER 16, 2015 NMX-J-626-ANCE-2015 CSA C22.2 NO. 263-15 UL 218 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Reasons for differences from IEC This standard provides requirements for re pump controllers for use in accordance with the electrical installation codes of Canada