AIR FORCE MIL-R-38213 B-1983 RAINCOAT MAN'S LIGHTWEIGHT BLUE《蓝色轻质男式雨衣》.pdf

《AIR FORCE MIL-R-38213 B-1983 RAINCOAT MAN'S LIGHTWEIGHT BLUE《蓝色轻质男式雨衣》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-R-38213 B-1983 RAINCOAT MAN'S LIGHTWEIGHT BLUE《蓝色轻质男式雨衣》.pdf（43页珍藏版）》请在麦多课文档分享上搜索。

1、T MIL-R-38213B L( 979990b OL(41LO 2 N MIL-R-38213B(USAF) 22 November 198? SUPERSEDING 28 May 1965 * MIL-R-38213A(USAF) MILITARY SPECIFICATION RAINCOAT, MANS, LIGHTWEIGHT, BLUE This specification is approved for use by the Department of the Air Force, and is available for use by all Departments and A

2、gencies of the Department of Defense. 1. SCOPE 1.1 ScoDe. This specification covers the requirements for a mans lightweight, blue raincoat. 1.2 Classification. The raincoat shall be of one type in the following lengths and sizes, as specificed (see 6.2): Schedule of lengths and sizes Short 32 34 36

3、38 40 42 44 46 48 Regular 32 34 36 38 40 42 44 46 48 50 Long 34 36 38 40 42 44 46 48 Extra Long 34 36 38 40 42 44 46 48 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 SPecifications and standards. Unless otherwise specified, the following specifications and standards of the issue listed in t

4、hat issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL A-A-203 Paper, Kraft, Untreated U-T-30 Talcum Powder V-B-87 1 Button, Sewing Hole, and Button,

5、 Staple, (Plastic) V-T-276 Thread, Cotton Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: ASD/ENES, Wright-Patterson AFB OH 45433 by using the self-addressed Standardization Document Improvement

6、 Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 8405 Obtained From GLOBAL.ENGINEERING DOCUMENTS 2625 So.Hickorv St. Santa Ana, CA 92707 (71 4)540-9870: (800)854-7179 U Licensed by Information Handling ServicesMIL-R-38233B 84 .797970b 0443933 4 MIL-R-38213B(USAF) V-T-

7、280 DDD-L-20 PPP-B-636 MILITARY MIL - C-29 7 MIL- C- 339 5 MIL-T-3530 MIL-C-14366 MIL-C-43718 STANDARDS FEDERAL FED-STD-175 FED-STD-191 FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-1393 Thread, Gimp, Cotton, Buttonhole Label: For Clothing, Equipage, and Tentage, (General Use) Boxes, Shipping

8、, Fiberboard Cloth, Interlining, Cotton Warp, and Spun Hair-Wool or Rayon Filling Cloth, Netting; Nylon or Polyester Thread and Twine; Mildew Resistant or Water Repellent Treated Cloth, Coated, Nylon, Twill (One Side Coated) Cloth, Twill, Polyester; Polyester and Cotton; Polyester and Rayon Adhesive

9、s, Methods of Testing Textile Test Methods Stitches, Seams, and Stitchings .- Sampling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage Provisions for Evaluating Quality of Coated Fabric Raincoats (Copies of specifications and standards required by manufacturers in

10、 connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other Dublications. The following documents form a part of this specification to the extent specified herein. The issues of the document which is indicated

11、 as DoD adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D 3951 Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Mate

12、rials, 1916 Race St., Philadelphia PA 19103.) (Industry association specifications and standards are generally available for reference from libraries. using Federal agencies.) They are also distributed among technical groups and THE COLOR ASSOCIATION OF THE U.S., INC, Department of Defense (DoD) Sta

13、ndard Shades for Buttons 1966 Department of Defense (DoD) Standard Color Card of America (Application for copies should be addressed to The Color Association of the U.S., Inc., 24 East 38th St., New York NY 10016.) 2 Licensed by Information Handling Servicest MIL-R-382L3B 4 m 7399906 044171i2 b m MI

14、L-R-38213B(USAF) . 2.3 Order of Drecedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. 3. REQUIREMENTS 3.1 Guide samDle. Samples, when furnished, are solely for guidance and information to t

15、he contractor (see 6.3). appear in the sample, in which case the document shall govern. Variations from the document may 3.2 Materials 3.2.1 Coated fabric. The coated fabric shall conform to type I of MIL-C-14366 except that the cloth shall have good colorfastness to crocking and shall be tested for

16、 crocking in accordance with test method 5651 of FED-STD-191. The color of the fabric shall match USAF Color Shade No. 1157 (see 6.3). 3.2.2 Nvlon cloth, The lining for the body, the sleeves, and the back yoke shall be nylon taffeta cloth. The finished cloth shall be clean, evenly woven and shall co

17、nform to the quality and grade of product specified herein. 3.2.2.1 first quality; 70 denier; bright, semibright, or semidull; continuous filament. yarns with 34 filaments and with suitficient twist to meet the requirements of this specification. The fibers shall be nylon 66 (polyhexamethylene adipa

18、mide), having a minimum melting point above 450F when tested as specified. Yarns. Warp and filling yarns of the nylon taffeta cloth shall be 3.2.2.2 Phvsical reauirements. The finished nylon cloth shall conform to the requirements listed in table I. TABLE I. Phvsical reauirements of nvlon cloth. I C

19、haracteristic Weave Weight, ounces per square yard Yarns per inch Warp Filling Breaking strength, pounds Warp Filling Tearing strength, pounds Warp Filling Requirement Plain 1.9 20.15 108 minimum 71 minimum 125 minimum 85 minimum 5 minimum 3.5 minimum 3 Licensed by Information Handling ServicesMIL-R

20、-3213B L( 799740b 0441713 1 MIL-R-38213B(USAF) 1 3.2.2.3 Color. The color of the cloth shall match USAF Color Shade No. 1157 (see 6.3). Unless otherwise specified, the cloth shall be dyed with applicable premetallized or acid dyes. 3.2.2.3.1 Matchina. The color shall match the standard shade sample

21、(see 6.3) under artificial daylight having a color correlated temperature of 7000 2500 kelvins and shall be a good approximation to the standard sample under incandescent lamplight at 2850 2100 kelvins. 3.2.2.3.2 Colorfastness. The dyed cloth shall have good colorfastness to laundering, perspiration

22、, and crocking when tested as specified in 4.2.1. 3.2.2.4 Nonfibrous material. The starch and protein content of the cloth shall not exceed 1 percent when tested as specified in 4.2.1. 3.2.2.5 Shrinkage. The cloth shall be preshrunk and shall not shpink more than 2 percent in the direction of either

23、 the warp or filling when tested as specified in 4.2.1. 3.2.3 Interlininq. The material for interlining the lapel facing and collar shall conform to type II of MIL-C-297. The material used for interlining the for lining pockets shall conform to class 1 of MIL-C-43718. The color for all . interlining

24、s shall be black. shoulder loops, sleeve tabs, front facing tab, pocket welts, front edges and 3.2.4 Nvlon netting material. The material for ventilating the back shall conform to type I of MIL-C-3395. The color shall be natural. The requirements for colorfastness, mildew resistance, and loss in bre

25、aking strength after exposure for 240 hours shall not apply. 3.2.5 Thread. The thread for seaming, stitching, and buttonhole making shall conform to type IA3, ticket No. 50, 3 ply and type IA3, ticket No. 60, 3 ply of V-T-276, and the thread for sewing on buttons shall conform to types IA3, ticket N

26、o. 20, 4 ply of V-T-276. All colored thread shall be vat dyed to match the material upon which it is sewn and shall show good colorfastness to laundering and weathering. conforming to type II, class 1 of MIL-T-3530. The thread or fabric shall not be lubricated by any means prior to or during seaming

27、. 3.2.6 Gim. the basic fabric and shall conform to type I, size No. 8 of V-T-280. The gimp shall have a good colorfastness to laundering and shall have a water-repellent finish conforming to type II, class 1 of MIL-T-3530, The thread shall have a water-repellent finish The gimp for reinforcing the b

28、uttonholes shall match the color of 3.2.7 Buttons, The buttons shall conform to type II, class D, sizes 24 line, 30 line, and 45 line, styles 20 or 21, and size 18 line, style 15 of V-B-871. The buttons shall have a glossy finish, and the color of the buttons shall approximate blue USAF Color Shade

29、No. 1157 (see 6.3). 4 Licensed by Information Handling Services_- MIL-R-38213B 84 479770b OqY17Li.I T MIL-R-38213B(USAF) 3.2.8 Evelets. Ventilating eyelets shall be made of brass or aluminum. The outside diameter shall be 0.24 to 0.32 inch for the top flange, and the inside diameter shall be 0.12 to

30、 0.20 inch. The eyelets shall be enameled to match the basic fabric. 3.2.9 Seam taDe. The seam tape shall be of basic fabric, bias cut 1 41/8 inch wide 3.2.10 Seam sealant. The seam sealant shall be a virgin polyvinyl butyral, plasticized with phosphate or phthalate ester plasticizers exclusively an

31、d may be pigmented or filled to aid in shortening the drying time. The sealant when appliedsto the raincoat shall produce a stripe that does not differ materially in color from the surrounding area. The seam sealant when used in combination with the coated fabric being used shall comply with the req

32、uirements specified in table II when tested as specified in 4.3.1. TABLE II, Phvsical reauirements of seam sealant. Characteristic Hydrostatic resistance of seam sealant Blcking resistance (16OOF) scale rating Resistance to low temperature Stiffness Initial, centimeters After heat aging, centimeters

33、 2/ Solids content, percent Requirement Maximum No. 3 of 5872 ( FED-STD- I 9 i ) 7 10 Minimum No leakage 1/ Pass 2/ 20 - I/ - 2/ Leakage shall be defined as the appearance of water at three different places in any portion of the 4-1/2-inch diameter test areas. The seam sealant shall show no cracking

34、, no flaking, and no separation from the fabric. 3.2.11 Adhesive for reinforcement Datches, seam taDe, and adhering of voke to back. The adhesive used for adhering of-reinforcement patches, seam tape and adhering of yoke to the back of the raincoat shall be a buna-N rubber base adhesive conforming t

35、o the requirements of table III when tested as specified in 4.3.2. 5 Licensed by Information Handling ServicesMIL-R-38213B(USAF) 7 TABLE III. Phvsical reauirements of adhesive. Requirement Characteristic Maximum Minimum Adhesive Initial, pounds per 2 inches 4 2.5 After aging, pounds per 2 inches Fle

36、xibility Initial, centimeters 15 After aging, centimeters 16 3.2.12 Seam dustina material. All sealant and exposed reinforcement adhesive areas shall be dusted with talcum powder conforming to U-T-30. 3.2.13 Labels. Each raincoat shall have a size label and a combination identification, instruction

37、and personal label conforming to DDD-L-20. The raincoat is not intended to be laundered. The combination identification, instruction and personal label is only required to be fast to the laundering transference test specified in DDD-L-20, and the colorfastness of the label is not required. If the la

38、bel is clearly legible after laundering, it shall be satisfactory. 3.2.13.1 Size label. The size label shall show the size of the raincoat in black letters and numerals and shall conform to type VI, class 2 of DDD-L-20. The length may be abbreviated as follows: A sufficient margin shall be allowed a

39、t the top of the label so that the inscription will be visible when the label is sewn in the collar. 3.2.13.2 Combination label. The combination identification, instruction and personal label shall conform to type VI, classes 10 and 15 of DDD-L-20. The combination label shall bear the following insc

40、ription: S (Short), R (Regular), or L (Long). Name : Service No.: Raincoat, Mans, Lightweight, Blue Contract No.: DLA-100-00-0-0000 (Example) Stock No.: 8405-00-000-0000 (Example) Suppliers Name: MIL-R-38213B(USAF) CLEANING INSTRUCTIONS 1. Do not dry clean, launder, or press. 2. Remove spots by rubb

41、ing gently with mild soap and,water or with mild detergent and water. length to remove wrinkles. 3. When not in use, hang raincoat at full 6 Licensed by Information Handling Services MIL-R-38213B 84 777770b 04Y171b 3 R c 3.3 Desian. The raincoat shall be single breasted and shall have a button fly f

42、ront, a button tab closure on the lower left facing, shoulder loops, a convertible collar with a collarstand, welt style pockets with pass-thru, and upper back storm shield. lined with nylon taffeta cloth. The raincoat shall be quarterlined and the sleeves 3.3.1 Patterns, Standard patterns, which pr

43、ovide a 3/8-inch seam allowance for regular and double-lapped seams, 5/8 inch for lining seams, 3/8 inch for armhole seams from step to step, 3/16 inch at the bottom of the armhole seams from step to step and a 1/4 inch for joining netting to the back, will be furnished by the Government (see 6.3).

44、The Government patterns, which show directional lines and markings for proper assembly, shall not be altered in any way and are to be used as a guide for cutting suppliers working patterns, Seam allowances shall be in accordance with those shown, unless otherwise specified. and the corners shall not

45、 be cut off. The working patterns shall be identical to the standard patterns 3.4 Construction. The construction of the raincoat shall be in accordance with table IV, Unless otherwise specified herein, the manufacturer will not be required to follow the exact sequence of operations as listed therein

46、. 3.4.1 Stitches, seams. and stitchinq. All stitches, seams and stitching shall shall be as specified in table IV. seams sewn so that no raw edges, run-Offs, pleats, puckers or open seams occur. When two or more methods of seams or stitches are given for the same operation, any one may be used. Wher

47、e stitch type 401 is used, the looper (underthread) shall be on the inside of the raincoat. Except that the lower thread shall be 60/3 ply when sewing on buttons and when stitch type 401 is used, the upper and lower threads for sewing shall be 50/3 ply. conform to FED-STB-751. The type of seam, stit

48、ching, and stitches per inch . ._ Seam allowances shall be maintained with 3.4.1.1 shall be secured by stitching back of the break 1/2 to 1 inch. Ends of seams produced with stitch type 301, if not caught in other seams or stitching, shall be securely backtacked. Thread breaks and ends of seams. Thr

49、ead breaks of all stitch types 3.4.1.2 Stitches Der inch. inch shall be as specified in table IV. The minimum and maximum number of stitches per 3.4.2 Buttonholes. The purling on the buttonhole on the left lapel shall be on the facing. The purling on the buttonhole on the front fly shall be on the facing side of the fly. The purling on the buttonholes on the facing tab and the shoulder loops shall be on the outside of the tab and the loops. stitching shall be securely caught in the fabric, 3.4.3 Sealinn of seams and stitchinas. All side seams, sleeve armhole joining seams, sl