AIR FORCE MIL-DTL-87173 B-1998 PROPELLANT PRIMING FLUID ALCM ENGINE GRADE PF-1《PF-1级射引擎起爆临界流体推进剂》.pdf
《AIR FORCE MIL-DTL-87173 B-1998 PROPELLANT PRIMING FLUID ALCM ENGINE GRADE PF-1《PF-1级射引擎起爆临界流体推进剂》.pdf》由会员分享,可在线阅读,更多相关《AIR FORCE MIL-DTL-87173 B-1998 PROPELLANT PRIMING FLUID ALCM ENGINE GRADE PF-1《PF-1级射引擎起爆临界流体推进剂》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、 MIL-DTL-87173B 6 Ob 20bL484 Lb2 MIL-DTL-87173B(USAF) 13 February 1998 SUPERSEDING 23 June 1989 MIL-P-87173A(USAF) DETAIL SPECIFICATION PROPELLANT, PRIMING FLUID, ALCM ENGINE, GRADE PF-1 1 Inactive for new design after 13 February 1998. I This specification is approved for use by the Department of t
2、he Air Force and is available for use by all Departments and Agencies of the Department of Defense. i. SCOPE 1.1 Scope. This specification covers one grade of highdensity hydrocarbon fuel. This specification was thoroughly reviewed as a part of acquisition reform. While most of the requirements were
3、 converted to performance terms, due to the military-unique nature of the product (see 6.1) and the need for compatibility with deployed systems, it was determined that not all requirements could be converted. The issuance of this specification as “detail“ is not intended to constrain technology adv
4、ances in future systems. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples.
5、While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents 2.2.1 Specifications and standards
6、. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Sfandards (DoDISS) and supplement thereto, cited
7、in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: ASCIENSI, Bldg 560, 2530 Loop Rd. West, Wright-Patterson AFB OH 45433-7 1 01, by using the Standardization Document
8、 Improvement Proposal (DD Form 1426) appearing at the end of this document, or by letter. AMSC NIA FSC 9135 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesMlL-TL-87173B( USAF) SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-1-85470
9、 Inhibitor, Icing, Fuel System, High Flash STANDARDS FEDERAL FED-STD-791 Lubricants, Liquid Fuels, and Related Products; Methods of Testing DEPARTMENT OF DEFENSE MIL-STD-290 Packaging of Petroleum and Related Products (Unless otherwise indicated, copies of the above specifications and standards are
10、available from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia PA 191 11- 5094.) 2.3 Non-Government publications. The follouring documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents whic
11、h are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS STANDARDS ASTM D93 Tes
12、t Methods for Flash Point by Pensky-Martens Closed Tester (DoD adopted) ASTM DI56 ASTM D240 ASTM D381 ASTM 0445 ASTM DI298 ASTM D2276 ASTM D2382 ASTM D2386 ASTM D3241 Test Methods for Saybolt Color of Petroleum Products (Saybolt Chromometer Method) (DoD adopted) Standard Test Method for Heat of Comb
13、ustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (DoD adopted) Standard Test Method for Existent Gum in Fuels by Jet Evaporaon (DoD adopted) Standard Test Method of Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic /iscosity) (DoD adopted) Standard Test Meth
14、od for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method (DoD adopted) Standard Test Methods for Particulate Contaminant in Aviation Turbine Fuels (DoD adopted) Standard Test Method for Heat of Combustion of Hydrocarbon
15、 Fuels by Bomb Calorimeter (High-Precision Method) (DoD adopted) Standard Test Method for Freezing Point of Aviation Fuels (DoD adopted) Standard Test Method for Thermal Oxidation Stability of Aviation Turbine Fuels (JFTOT Procedures) (DoD adopted) . 2 Licensed by Information Handling Services. c AS
16、TM D3828 ASTM D4052 ASTM D4057 ASTM D5006 ASTM D5452 ASTM D6045 ASTM E29 ASTM E300 MIL-DTL-87173B ils 9999906 20bL4b T35 sl MIL-DTL-87173B( USAF) Standard Test Method for Flash Point by Setatlash Closed Tester (DoD adopted) Standard Test Method for Density and Relative Density of Liquids by Digital
17、Density Meter (DoD Adopted) Standard Practice for Manual Sampling of Petroleum and Petroleum Products (DoD adopted) Standard Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels (DoD Adopted) Standard Test Method for Particulate Contamination in Aviation Fuels b
18、y Laboratory Filtration (DoD Adopted) Standard Test Method for Color of Petroleum Products by the Automatic Trictimuluc Method Recommended Practice of Indicating Which Places of Figures are to be Considered Significant in Specified Limiting Values (DoD adopted) Sampling Industrial Chemicals, Practic
19、e for (Application for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken PA 19428-2959; (61 O) 832-9500.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the te
20、xt of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. Except as otherwise specified herein, the priming fluid shall consist completely of a mixture of exo-tetra
21、hydrodi(cyc1opentadiene) and methylcyclohexane. 3.1 .I Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided the material meets or exceeds the operational and maintenance requ
22、irements, and promotes economically advantageous life cycle costs. 3.2 Chemical and physical requirements. The chemical and physical requirements of the priming fluid shall conform to those listed in table I. 3.2.1 Additives. The additives listed shall be used in combination in amounts not to exceed
23、 those specified. Information concerning the type and amount of each additive used shall be made available when requested by Procuring Activity or User. 3.2.2 Antioxidants. The following active inhibitors shall be blended separately or in combination into the priming fluid in total concentration of
24、90 parts per million (minimum) to I1 O parts per million (maximum), by weight, not including weight of solvent, in order to prevent the formation of polymeric oxidation products: a. 2,6-di-tert-butyl-4-methylphenol b. 6-tert-butyl-2,4-dimethyIphenol c. 2,6-di-tert-butylphenol 3 Licensed by Informati
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AIRFORCEMILDTL87173B1998PROPELLANTPRIMINGFLUIDALCMENGINEGRADEPF1PF1 引擎 起爆 临界 流体 推进 PDF
链接地址:http://www.mydoc123.com/p-427772.html