AIR FORCE A-A-59320-2003 OHMMETER《欧姆表》.pdf

《AIR FORCE A-A-59320-2003 OHMMETER《欧姆表》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-59320-2003 OHMMETER《欧姆表》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 . . A-A-59320 26 August 2003 COMMERCIAL ITEM DESCRIPTION OHMMETER The General Services Administration has authorized the use of this Commercial Item description (CID) for all federal agencies 1. SCOPE. This Commercial Item Description (CID) describes an ohmmeter. This CID is meant as a minimum requ

2、irement for the ohmmeter, in which only those manufacturers that meet or surpass the following requirements are supplied per this CID. 2. SALIENT CHARACTERISTICS. The equipment shall be capable of operation within the accuracies, limits, and specifications herein. The equipment shall be Class 3 in a

3、ccordance with MIL-PRF-28800 except as specified herein. 2.1 Order of Precedence. In the event of a conflict between the text of this CID and the references cited herein (except for associated detail specifications), specification sheets or MS standards the text of this CID shall take precedence. No

4、thing in this CID, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 2.2 Safety and Environmental. The equipment shall meet all safety and environmental requirements as specified in MIL-PRF-28800 for the classification as stated herein. 2.3 Relia

5、bility. The design of the equipment shall be such that under normal use and operation the equipment does not fail within 2000 hours of operation with a statistical certainty of 95%. AMSC N/A FSC 6625 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that m

6、ay improve this document should be sent to: WR-ALC/LEEC, 295 Byron Street, Robins AFB, GA 31098-1611 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59320 22.4 Calibration and Maintenance Adjustments. The design of the system shall pro

7、vide for readily accessible calibration and maintenance adjustments. These adjustments shall be provided by variable value components, which are adjustable, by the use of simple means. The calibration by substitution of selected components or parts is unacceptable unless specifically approved. The c

8、alibration adjustments, wherever possible, shall be accessible without removal of the instrument case or modules. The calibration interval shall be a period of one year or greater, based on an operating time of 2000 hours per year. 2.5 Electrical Power Sources and Connections. The equipment shall op

9、erate from nominal commercial power source of 115/230 Volts AC ( 10 %) at line frequencies of 50 Hz to 60 Hz ( 5 %) or Internal Battery. 2.6 Internal DC Power. DC power shall be supplied by internal, rechargeable storage batteries. The equipment shall be capable of operating away from an external AC

10、 power source. The rechargeable batteries shall have the capability of operating the unit with full performance for a period of not less than four hours for the operating temperature range specified herein. The batteries shall conform to MIL-PRF-28800. 2.7 Recharge Time. The charger circuitry shall

11、be such that a condition of charge, which shall permit at least four hours of continuous use of the unit, within all specification requirements, shall be reached in no more than sixteen hours following a low battery indication. Under no condition of discharge shall the charging rate applied to the b

12、attery exceed the battery manufacturers recommended maximum rate, nor shall an indefinite charging period result in any damage to the battery or any other components. 2.8 Battery Charger. An internal battery charger shall be provided in accordance with MIL-PRF-28800, Section 3. 2.9 Accessories. Acce

13、ssories to be supplied by the manufacturer with each deliverable piece of equipment shall include standard accessories as provided by the manufacturer and listed in the manufacturers catalog or data sheet, a written tutorial/user reference manual, a written programmer reference manual, a traceable c

14、alibration certificate, and a complete set of test leads with provisions for storage. 2.10 Temperature Requirement. Unless otherwise specified herein, the equipment shall meet its specified performance characteristics and other requirements when subjected to the class 3 temperature requirements spec

15、ified by MIL-PRF-28800 and as listed below. 2.11 Non-Operating Temperature. The equipment shall meet its performance and accuracy requirements in a non-operating environment of 10 C to + 50 C. 2.12 Operating Temperature. The equipment shall meet its performance and accuracy requirements in an operat

16、ing environment of 10 C to + 40 C. 2.13 Performance Characteristics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59320 32.13.1 Resistance Ranges. The equipment shall have the capability to perform measurements from 0 to 199.99 ohms with suffi

17、cient range selection to meet the resolution and accuracy stated herein. The equipment shall have the capability to provide both automatic and manual range selection. 2.13.2 Accuracy. The accuracy of the equipment shall be at least 0.2% of the reading plus three counts. 2.13.3 Maximum Test Current.

18、The maximum continuity test current shall not provide more than 10 Amps for the ranges from 0 to 199.99 milliohms, and shall not provide more than 1 Amp for the ranges from greater than 199.99 milliohms to 199.99 ohms. 2.13.4 Maximum Open Terminal Voltage. The open terminal voltage shall not be grea

19、ter than 2.0 Volts on any range. 2.13.5 Over-range. The equipment shall be provided a method for indicating an over-range condition. 2.13.6 Measurement Method. The equipment shall have a four terminal measurement method to assure measurement accuracy. 2.13.7 Display. The equipment shall have a displ

20、ay with the resolution to produce the required accuracy stated herein. 3. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANC

21、E 4.1 Product Conformance. The Products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right

22、to require proof of such conformance. 4.2 Metric Products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the specified tolerance using conversion tables contained in the latest revision of Fed

23、eral Standard No. 376, and all other requirements of this CID are met. If a product manufactured to metric dimensions exceeds the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. 4.3 The contracting officer h

24、as the option of accepting or rejecting the product. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59320 45. PACKAGING. 5.1 Preservation, Packing, and Marking. Preservation, packing, and marking shall be as specified in the contract or order. 6

25、. NOTES. 6.1 Sources of Documents. 6.1.1 Military Specifications, Standards, and Handbooks referenced herein may be obtained from the Standardization Documents Order Desk, 700 Robbins Ave, Bldg 4, Section D, Philadelphia, PA 19111-5094. 6.1.2 The Code of Federal Regulation (CFR) may be obtained from

26、 the Superintendent of Documents, U.S. Government Printing Office, Washington, DC, 20402. 6.2 Key Words: milli-ohms MILITARY INTEREST Custodian: Preparing activity: Air Force 99 Air Force - 84 Agent: Air Force - 99 (Project 6625-0927) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-