AECMA PREN 3155-004-2000 Aerospace Series Electrical Contacts Used in Elements of Connection Part 004 - Contacts Electrical Male Type A Crimp Class T Product Standard Edition P 3《航.pdf

《AECMA PREN 3155-004-2000 Aerospace Series Electrical Contacts Used in Elements of Connection Part 004 - Contacts Electrical Male Type A Crimp Class T Product Standard Edition P 3《航.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 3155-004-2000 Aerospace Series Electrical Contacts Used in Elements of Connection Part 004 - Contacts Electrical Male Type A Crimp Class T Product Standard Edition P 3《航.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD NORME AECMA AECMA NORM I I aecma 20( prEN 31 55-004 Edition P 3 February 2000 Edition approved for publication PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (+32) 2 775 81 10 - Fax. (+32) 2 775 81 11 Superseding edition P

2、 2 ICs: 49.060 February 1997 Descriptors: Comments should be sent within six months C2 Chairman after the date of publication to ENGLISH VERSION Aerospace series Electrical contacts used in elements of connection Part 004: Contacts, electrical, male, type A, crimp, class T Product standard Srie aros

3、patiale Contacts lectriques utiliss dans les organes de connexion Partie 004: Contacts lectriques, mles, type A, sertir, classe T Norme de produit Luft- und Raumfahrt Elektrische Kontakte zur Verwendung in Verbindungselementen Teil 004: Elektrische Stiftkontakte, Typ A, crimpbar, Klasse T Produktnor

4、m This %Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA- Members. It has been technically approved by the experts of the concerned Technical Committee following

5、 comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standa

6、rd Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it wi/ be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. 2000-02-29 AECMA Gulledelle 94 8-1200 BRUXELLES Mr Peuetta Copyright Association Europeene

7、des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN 3155-004-ENCL Zoon W LUL23Ll E017b78 452 = Page 3 prEN 3155-004: 2000 O introduction The contacts defined by this standa

8、rd are derived from those of MIL-C-39029/4 and, intermateable with those of MIL-C-39029/5. They are specified as a 260 “C class instead of a 200 “C class as detailed in the MIL standard. 1 Scope This standard specifies the required characteristics, tests and tooling applicable to male electrical con

9、tacts 004, type A, crimp, class T, used in elements of connection according to EN 3155-002. It shall be used together with EN 31 55-001. The associated female contacts are defined in EN 31 55-005. 2 Normative references This European Standard incorporates by dated or undated reference provisions fro

10、m other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendme

11、nt or revision. For undated references the latest edition of the publication referred to applies. IS0 8843 EN 2083 EN 2591* EN 3155-001 EN 3155-002 EN 3155-005 MI L-DTL-22520 MI L-C-22520/1 MI L-C-22520/2 MIL-C-2252017 MI L-C-39029/4 MIL-C-39029/5 MI L-I-81969/14 MlL-I-81969/30 Aircraft - Crimp-remo

12、vable contacts for electrical connectors - Identification system Copper and copper alloy conductors for electrical cables - Aerospace series 1) Aerospace series - Elements of electrical and optical connection - Test methods - General Aerospace series - Electrical contacts used in elements of connect

13、ion - Part 001: Technical specification 2) Aerospace series - Electrical contacts used in elements of connection - Part 002: List and utilization of contacts 2) Aerospace series - Electrical contacts used in elements of connection - Part 005: Contacts, electrical, female, type A, crimp, class T - Pr

14、oduct standard 2) Crimping tools, terminal, hand or power actuated, wire termination and tool kits, general specification for 3) Crimping tools, terminal, hand, wire termination for wire barrel sizes 12 through 20 3) Crimping tools, terminal, hand, wire termination for wire barrel sizes 20 through 2

15、8 3) Crimping tools, terminal, hand, wire termination for wire barrel sizes 16, 20 and 22 3) Contacts, electrical connector, pin, crimp removable, (for MIL-C-26482 series 2, MIL-C-81703 series 3, MlL-C-83723 series I and III, and MIL-C-83733 connectors) Contacts, electrical connector, socket, crimp

16、removable, (for MIL-C-26482 series 2, MIL-(2-81703 series 3, MIL-C-83723 series I and III, and MIL-C-83733 connectors and MIL-S-12883/40 and /41 relay sockets) 3) Installing and removal tools, connector electrical contact, type III, class 2, composition B 3) Installing and removal tools, connector e

17、lectrical contact, type II, class 2, composition C for unwired 3) * And all its parts quoted I) Published as AECMA Standard at the date of publication of this standard 2) Published as AECMA Prestandard at the date of publication of this standard 3) Published by: Department of Defense (DOD), the Pent

18、agon, Washington D.C. 20301 USA Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN 3155-00i-ENGL 2OUO m 1012311 0017b77 377 m Page 4 prEN 3

19、155-004: 2000 3 Definitions For the purposes of this standard, the definitions given in EN 3155-001 apply. 4 Required characteristics 4.1 Specific characteristics Type A contacts are for general application and class T corresponds to an operating temperature range from - 65 “C to 260 OC. 4.2 Dimensi

20、ons and mass See figure 1, figure 2 and table 1. Dimensions and tolerances are given in millimetres and apply after surface treatment. x (2:11 Figure I 1,52 I27 I I 16“ 14“ / r I Y I k-l 8 8 i Radii / / Figure 2: Barrel, contacts 16-18 and 12-12 Copyright Association Europeene des Constructeurs de M

21、ateriel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Table 1 Page 5 prEN 3155-004: 2000 Size A Contact Barrel max. 20 20 18,29 20 18 18,29 16 16 20,85 16 14 20,85 16 18 20,85 4.3 Marking by colour code See tabl

22、e 2. Table 2 0,30 0,23 - 0,65 - 0,651 0,81 0,43 0,81 0,43 0,43 2,56 1,19 3,94 2862 0,65 1,57 4,01 1,36 Two bands according to IS0 8843 I Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permi

23、tted without license from IHS-,-,- STD-AECMA PREN 3155-OUY-ENGL 2000 10L23LL UOL77OL 877 = Page 6 prEN 3155-004: 2000 Size Contact Barrel 20 20 20 18 16 16 16 14 16 18 12 12 4.4 Material, surface treatment - Body material: copper alloy - Surface treatment: gold on an appropriate undercoat, thickness

24、 of protection not specified, selective protection permitted. Size of conductors Rated test current A AWG a AECMA Section Code mm2 006 0,60 20 795 004 0,40 22 5,O 002 0,25 24 390 O1 o 1 ,o0 18 7,s 006 0,60 20 7,5 002 0,25 24 310 004 0,40 22 5,o o1 2 1,20 16 13,O o1 o 1 ,o0 18 10,o 006 0,60 20 715 02

25、0 2,OO 14 13,O 012 1,20 16 13,O O1 o 1 ,o0 18 10,o o1 o 1 ,o0 18 11,o 006 0,60 20 7,5 004 0,40 22 50 002 0,25 24 310 030 3,OO 12 23,O 020 2,oo 14 17,O 4.5 Permissible cables See table 3. Table 3 4.6 Tooling 4.6.1 Crimping tools Conform to MIL-DTL-22520, see table 4. The qualification selector number

26、 used for crimping copper or copper alloy conductors in cables EN 2083 are indicated in table 4. It is the responsability of the user if the parameters in tabe 4 are changed for service use. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with

27、AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3155-004: 2000 Size Contact Barrel Insertion tools 20 20 M81969/14-11 20 18 M81969/14-11 16 16 M81969/14-O3 Table 4 Extraction tools Wired contact Unwired contact M81969/14-11 M81969/30-O5 M81969/14-I 1 M819

28、69/30-05 M81969/14-03 M81969/30-O6 Contact 1 Cable size 1 Tools M2252011-01 I Tools M22520/2-01 I Tools M2252017-01 16 16 ontact size - 20 - 20 - 16 - 16 - 16 14 M81969/14-O3 M81969/14-03 M81969/30-O6 18 M81969/14-03 M81969/14-04 M81969/30-O6 a AWG = Closest American Wire Gage. I 12 4.6.2 Insertionl

29、Extraction tools Conform to MIL-1-81969. See table 5. Table 5 14 1 M81969114-04 I M81969114-O4 I M81969/30-07 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from I

30、HS-,-,-STD-AECMA PREN 3155-0Ilq-ENGL 2000 LOLi23L1 0017703 b4T W Page 8 prEN 3155-004: 2000 Size Contact Barrel Stripped length of cable mm I0,5 20 20 20 18 485 16 16 14 18 12 12 Discontinuity of contacts in the microsecond range Electrical overload ContacUconductor joint ageing by current and tempe

31、rature cvclina X X X Shock I Ix I Rapid change of temperature Salt mist Fluid resistance Gas-tightness of solderless wrapped connections X X X X Sinusoidal and random vibrations Mechanical endurance Test probe damage (female contact) Contact bending strength Tensile strength (crimped connection) Gau

32、ge insertion and extraction forces in and out of a female contact Stripping force, solderless wrapped connections X X X X X X X 4.7 Cable stripping See table 6. Table 6 I 16 I 16 I 4.8 Tests See table 7. Table 7 EN 2591- Test 1 O1 I Visual examination 102 I Examination of dimensions and mass 20 1 Co

33、ntact resistance - Low level I 202 Contact resistance at rated current I 204 21 o 220 301 Endurance at temperature X I T = (260 f 2) “C Duration: I O00 h TA = (- 65 f 2) “C TB = (260 12) “C 305 307 31 5 31 9 402 403 406 At 260 “C temperature 41 5 41 6 417 41 8 424 (continued) Copyright Association E

34、uropeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PKEN 3255-00Y-ENGL 20nU E Ln12311 0017704 5b Page 9 prEN 3155-004: 2000 Table 7 (concluded) 4.9 Gauges Not applicabl

35、e. 5 EXAMPLE: Desi g na ti on Description block Identity block CONTACT ELECTRICAL EN31 55-004M201 Standard number Type of contact: M: male Contact size (see table I) 3 Barrel size (see table 1) NOTE: If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See EN 3155-001. Colour code: see table I. 7 Technical specification See EN 31 55-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-