AASHTO MP 33-2017 Standard Specification for Materials for Emulsified Asphalt Fog Seal.pdf

《AASHTO MP 33-2017 Standard Specification for Materials for Emulsified Asphalt Fog Seal.pdf》由会员分享，可在线阅读，更多相关《AASHTO MP 33-2017 Standard Specification for Materials for Emulsified Asphalt Fog Seal.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Standard Specification for Materials for Emulsified Asphalt Fog Seal AASHTO Designation: MP 33-171Technical Section 2a, Emulsified Asphalts Release: Group 3 (August 2017) American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 2000

2、1 TS-1a MP 33-1 AASHTO Standard Specification for Materials for Emulsified Asphalt Fog Seal AASHTO Designation: MP 33-171Technical Section: 2a, Emulsified Asphalts Release: Group 3 (August 2017) 1. SCOPE 1.1. This standard specifies quality requirements for emulsified asphalt as used for fog seals.

3、1.2. A fog seal is the light application of emulsified asphalt to the pavement surface, which may be used to provide a surface seal, arrest light raveling, or create color contrast between traffic lanes and shoulders to improve visibility. Fog seals are also applied to newly placed chip seals to loc

4、k in loose chips and provide a more aesthetically pleasing finished product. 2. REFERENCED DOCUMENTS 2.1. AASHTO Standards: M 140, Emulsified Asphalt M 208, Cationic Emulsified Asphalt M 316, Polymer-Modified Emulsified Asphalt T 304, Uncompacted Void Content of Fine Aggregate PP 88, Emulsified Asph

5、alt Fog Seal Design 3. TERMINOLOGY 3.1. Slow-setting type emulsified asphaltAny emulsified asphalt containing the designations CSS-1, CSS-1h, SS-1, and SS-1h. 3.2. Medium-setting type emulsified asphaltAny emulsified asphalt containing the designations CMS-2, MS-2, or HFMS-2. 3.3. Rapid-setting type

6、 emulsified asphaltAny emulsified asphalt containing the designations RS-2, CRS-2, or HFRS-2. 3.4. Quick-setting type emulsified asphaltAny emulsified asphalt containing the designations QS, CQS, CQS-1P, or CQS-1hP. 4. SIGNIFICANCE AND USE 4.1. This standard may be used to select and evaluate materi

7、als for use as emulsified asphalt fog seals. 2017 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.TS-1a MP 33-2 AASHTO 4.2. Fog seal emulsified asphalts are most typically slow-setting emulsified asphalt wit

8、hout polymer, including diluted versions of SS-1, SS-1h or CSS-1, CSS-1h. 4.3. For applications such as fog treatments on open-graded surface mixes, polymer-modified emulsified asphalt meeting the requirements of M 316 may be used. Dilution rates may vary, and residue application rates will increase

9、. These emulsified asphalts are usually made with slow setting or quick setting emulsifiers. 4.4. Fog seals are commonly applied over newly placed chip seals. When shorter curing times are needed for restoration of traffic, slow setting emulsified asphalts may be replaced by other types such as quic

10、k setting (QS or CQS), medium setting (MS or CMS), or even rapid setting (RS or CRS). 4.5. Small quantities of fine aggregate can be applied immediately behind the emulsified asphalt distributor to improve friction or to allow traffic to pass before the emulsified asphalt has cured. Fine aggregate u

11、sed for friction shall have a minimum angularity of 45 as determined by T 304. This requirement does not apply to fine aggregate used solely as a blotting material. 5. EMULSIFIED ASPHALT REQUIREMENTS 5.1. Before dilution, emulsified asphalt for fog seals shall meet requirements defined in M 140, M 2

12、08, or M 316 as applicable. The residue hardness classification is determined by the Owner Agency utilizing regional climatic and traffic conditions. 5.2. Fog seal emulsified asphalts are typically diluted 1:1 by weight with water or a compatible surfactant solution before application. The final dil

13、uted product shall be a fluid, homogeneous mixture that is capable of being sprayed evenly by a pressure distributor. All emulsified asphalt must be diluted at the manufacturers plant site. Slow-setting emulsified asphalt can be diluted with water. All other emulsified asphalt types must be diluted

14、by using a surfactant solution compatible with the emulsified asphalt. 5.3. To determine appropriate application rates, reference PP 88. 6. KEYWORDS Emulsified asphalt; fog seal; surface seal. 1This provisional standard was first published in 2017. 2017 by the American Association of State Highway and Transportation Officials. All rights reserved. Duplication is a violation of applicable law.