BS ISO IEC 29183-2011 Information technology Office equipment Method for measuring digital copying productivity of a single one-sided original《信息技术 办公设备 一个单面打印原件的数字复印生产力的测.pdf

《BS ISO IEC 29183-2011 Information technology Office equipment Method for measuring digital copying productivity of a single one-sided original《信息技术 办公设备 一个单面打印原件的数字复印生产力的测.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 29183-2011 Information technology Office equipment Method for measuring digital copying productivity of a single one-sided original《信息技术 办公设备 一个单面打印原件的数字复印生产力的测.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO/IEC 29183:2010 Information technology Office equipment Method for measuring digital copying productivity of a single one-sided originalBS ISO/IEC 29183:2010 BRITISH STA

2、NDARD National foreword This British Standard is the UK implementation of ISO/IEC 29183:2010. The UK participation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained on request to its secret

3、ary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 70326 3 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was p

4、ublished under the authority of the Standards Policy and Strategy Committee on 28 February 2011. Amendments issued since publication Date Text affectedBS ISO/IEC 29183:2010Reference number ISO/IEC 29183:2010(E) ISO/IEC 2010INTERNATIONAL STANDARD ISO/IEC 29183 First edition 2010-12-15 Information tec

5、hnology Office equipment Method for measuring digital copying productivity of a single one-sided original Technologies de linformation quipement de bureau Mthode de mesure de la productivit du copiage numrique dun simple original une face BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) PDF disclaimer Th

6、is PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept th

7、erein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;

8、the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOC

9、UMENT ISO/IEC 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member

10、 body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO/IEC 2010 All rights reservedBS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) ISO/IEC 2010 All

11、rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Test parameters and conditions3 4.1 Environment.3 4.2 Voltage3 4.3 Copying device setup .3 4.4 Paper.4 4.5 Maintenance.4 4.6 Preparation of test targets (test charts)4 5 Test met

12、hod .5 5.1 Test setup.5 5.2 Test measurement procedure 5 5.3 Test method process 8 5.3.1 Suggested test method process flow chart8 5.3.2 Single test target criteria 9 5.3.3 Estimating the copy count .9 5.3.4 5% consistency criteria.10 5.4 Performance test .10 6 Calculations and treatment of data .10

13、 6.1 Performance test .11 6.1.1 1 Copy Test 11 6.1.2 1 Copy + 30 Seconds Test11 6.1.3 1 Copy + 4 Minutes Test .12 7 Presentation of results12 7.1 Performance test .12 Annex A (informative) Examples of report presentation .14 Annex B (informative) Example of full detailed report.15 Annex C (normative

14、) Test targets for measurement of copying productivity.17 Bibliography18 BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) iv ISO/IEC 2010 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized syste

15、m for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees col

16、laborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standar

17、ds are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication

18、as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such paten

19、t rights. ISO/IEC 29183 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment. BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) ISO/IEC 2010 All rights reserved vIntroduction Many digital copying devices produce copied pages at a different r

20、ate than their nominal speed when running with different quality modes, different substrate weight, different job content and job lengths. The degree to which a change in productivity is experienced depends significantly on other parameters of the job stream. The most dominant of the parameters of t

21、he job stream are image quality modes selected, job content, black-and-white and colour reproduction job stream, and run length. ISO/IEC 24735 addresses the productivity issues for digital copying devices when using both collation and an automatic document feeder, but cannot be used for a single one

22、-sided original. This International Standard provides a general method for measuring productivity when the above-mentioned job stream parameters for digital copying devices are taken into consideration. This International Standard also includes instructions for the creation of test charts. It allows

23、 manufacturers and buyers of digital copying devices to describe the productivity of various digital copying devices with respect to representative office usage. BS ISO/IEC 29183:2010BS ISO/IEC 29183:2010 INTERNATIONAL STANDARD ISO/IEC 29183:2010(E) ISO/IEC 2010 All rights reserved 1Information tech

24、nology Office equipment Method for measuring digital copying productivity of a single one-sided original 1 Scope This International Standard specifies a method for measuring productivity of digital copying devices and multifunctional devices with various copying modes and a single one-sided original

25、. It is applicable to digital copying devices and multifunctional devices. It is intended to be used for black-and-white and colour digital copying devices and multifunctional devices of any underlying marking technology. This International Standard includes instructions for the creation of test cha

26、rts, test setup procedure, test procedure, and the reporting requirements for the digital copying productivity measurements. This International Standard is not intended to replace manufacturers rated speeds. 2 Normative references The following referenced documents are indispensable for the applicat

27、ion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2470-1:2009, Paper, board and pulps Measurement of diffuse blue reflectance factor Part 1: Indoor daylight conditi

28、ons (ISO brightness) ISO 536:1995, Paper and board Determination of grammage 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 full detailed report presentation of information including machine setup and measured test results 3.2 full report pr

29、esentation of results including the sFCOT (3.8), sESAT (3.7) and sEFTP (3.6) values as well as the calculated average for each value 3.3 nominal copying speed copy rate, excluding time to first page copied, as measured when producing pages in a continuous copy mode with a single static document usin

30、g a nominal weight substrate NOTE Nominal copying speed is expressed in copies per minute or images per minute (ipm). BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) 2 ISO/IEC 2010 All rights reserved3.4 performance test test used to evaluate productivity by providing sFCOT (3.8), sESAT (3.7) and sEFTP

31、(3.6) 3.5 saturated time per copy average time per copy measured from the complete exit of the first copy to the complete exit of the last copy 3.6 sEFTP effective throughput average speed at which a device produces pages measured from the initiation of the job through the complete exit of the last

32、copy NOTE 1 “s” denotes that a single one-sided original is used for the measurement. NOTE 2 sEFTP is expressed in images per minute (ipm); it can be affected by scan time, digital processing time, and maintenance, as well as the run time of the test. NOTE 3 A different term (“EFTP; effective throug

33、hput” for digital copying machines) is defined in ISO/IEC 24735. 3.7 sESAT estimated saturated throughput rate at which a device produces pages measured from the complete exit of the first copy to the complete exit of the last copy NOTE 1 “s” denotes that a single one-sided original is used for the

34、measurement. NOTE 2 sESAT is expressed in images per minute (ipm). NOTE 3 A different term (“ESAT; estimated saturated throughput” for digital copying machines) is defined in ISO/IEC 24735. NOTE 4 The parameter “continuous copying speed” for EP (electrophotographic) copying machines is defined in IS

35、O/IEC 21117. 3.8 sFCOT first copy out time number of seconds between the initiation of the job and the complete exit of the first copy NOTE 1 “s” denotes that a single one-sided original is used for the measurement. NOTE 2 sFCOT is strongly affected by the scanning time. NOTE 3 A different term (“FS

36、OT; first set out time” for digital copying machines) is defined in ISO/IEC 24735. NOTE 4 The parameter “first-copy-out time” for EP (electrophotographic) copying machines is defined in ISO/IEC 21117. 3.9 simplex copying use of a copying device when only a single side of a sheet is copied on NOTE Eq

37、uivalent terms are “one-sided copying” and “simplex to simplex” (referred to as 1:1 mode). BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) ISO/IEC 2010 All rights reserved 33.10 sLCOT last copy out time number of seconds between the initiation of the job and the complete exit of the last copy NOTE “s” d

38、enotes that a single original is used for the measurement. 3.11 summary report presentation of results including the average sFCOT (3.8) and sESAT (3.7) 3.12 test file digital file used for creating test targets (3.13) 3.13 test target hardcopy page used for testing according to the test method, cre

39、ated from the test file (3.12) NOTE An equivalent term is “test chart”. 4 Test parameters and conditions 4.1 Environment The test environment, including temperature and humidity, shall be within the ranges recommended by the manufacturer for operating the device. If no recommendation is available, t

40、he following ranges shall apply. Temperature: 18 C to 25 C Relative humidity: 30 % to 70 % The temperature and humidity ranges of the test environment should be recorded in the full detailed report (Annex B). 4.2 Voltage The copying device shall be connected to a voltage supply within the manufactur

41、er specified operating voltage range for the copying device under test. The measurement should be made under no-load condition prior to each test. 4.3 Copying device setup Place the copying device on a horizontal surface and set up the copying device according to the manufacturers recommendations. T

42、he copying device shall be fully enclosed in its normal exterior cover. The machine and all of its necessary supplies shall be acclimated in the test environment prior to conducting the test(s) for at least 8 hours. All supplies used in the test(s), including copy paper, shall be those specified by

43、the manufacturer. All image and copying modes shall be at their factory pre-set configuration for the copying device. It is assumed that the settings listed in Table 1 are common to all copying devices. These listed settings shall be set to the manufacturers default or pre-set condition for the devi

44、ce. If a device has settings not listed in Table 1, they too shall be set to default settings. For copying devices that have additional print quality and digital image processing features, those features shall be set to match their normal default condition, and included in the result reporting. Disa

45、bling manufacturer default installed features, routines or applications, is not allowed. Examples include, but are not limited to the following: automatic cleaning or calibration cycles, and energy save settings. If the system has automatic media detect(automatic paper type selection), it can be dis

46、abled, BS ISO/IEC 29183:2010 ISO/IEC 29183:2010(E) 4 ISO/IEC 2010 All rights reservedand paper used in the test shall be selected manually. This must be noted in the full detailed report (Annex B). The following pre-set values in the test will be noted on this report format. Additional optional test

47、s with non- default settings or configurations may be run. Table 1 Pre-set settings Pre-set item Pre-set value Output resolution default Output Quality default Copying mode default Auto density adjustment default Mode Collating function default Paper sending direction default Paper Paper type settin

48、g default Paper feeding default Paper Feeder Paper exit Standard exit tray Paper-path Face up exit default Fixing capability default Image quality stability default Capacity of paper default Temporary stop Others default If the copying device is setup with internal or external options such as memory

49、, sorter, or finisher as default, then these options should be noted on the full detailed report format in the configuration options as shown in Annex B, for example “Finisher as default” or “160GB HDD installed”. 4.4 Paper The output paper used in this test shall be within the range of, and/or not violate, specific written attribute guidelines and recommendations provided by the copying device manufacturer, which may include but are not be limited to: size, weight, composition, paper manufacturer(s), paper