BS ISO 8516-2011 Textile glass Textured yarns Basis for a specification《纺织玻璃纤维 膨体纱 基本规格》.pdf

《BS ISO 8516-2011 Textile glass Textured yarns Basis for a specification《纺织玻璃纤维 膨体纱 基本规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 8516-2011 Textile glass Textured yarns Basis for a specification《纺织玻璃纤维 膨体纱 基本规格》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 8516:2011 Textile glass Textured yarns Basis for a specificationBS ISO 8516:2011 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS

2、O 8516:2011. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all

3、the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 69444 8 ICS 59.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy a

4、nd Strategy Committee on 31 March 2011. Amendments issued since publication Date Text affectedBS ISO 8516:2011Reference number ISO 8516:2011(E) ISO 2011INTERNATIONAL STANDARD ISO 8516 Second edition 2011-02-15 Textile glass Textured yarns Basis for a specification Verre textile Fils texturs Base de

5、spcification BS ISO 8516:2011 ISO 8516:2011(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer per

6、forming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this

7、PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central

8、 Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in

9、 writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedBS IS

10、O 8516:2011 ISO 8516:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Designation 1 5 Physical properties .2 5.1 General .2 5.2 Type of glass2 5.3 Size content .2 5.4 Average filament diameter .2 5.5 Linear density 2 5.6

11、Moisture content2 5.7 Breaking load.2 6 Visual properties Defects.3 6.1 General .3 6.2 Visible defects of yarn 3 6.3 Visible defects of packages .3 7 Delivery.4 7.1 Presentation and packaging 4 7.2 Labelling.4 8 Storage .4 BS ISO 8516:2011 ISO 8516:2011(E) iv ISO 2011 All rights reservedForeword ISO

12、 (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical com

13、mittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrot

14、echnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the mem

15、ber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identify

16、ing any or all such patent rights. ISO 8516 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. This second edition cancels and replaces the first edition (ISO 8516:1987), of which it constitutes a minor revision. The main changes are as

17、follows: a) the normative references have been updated; b) old Clause 3, which concerned sampling, has been deleted as it referred the reader to ISO 1886 which has been withdrawn; c) a terms and definitions clause has been added (new Clause 3); d) Clause 7 has been revised as two clauses (Clause 7,

18、“Delivery”, and Clause 8, “Storage”). BS ISO 8516:2011 INTERNATIONAL STANDARD ISO 8516:2011(E) ISO 2011 All rights reserved 1Textile glass Textured yarns Basis for a specification 1 Scope This International Standard provides a basis for a specification applicable to textured yarns made from single o

19、r folded yarns of textile glass. Textured glass yarns can be produced by several types of process. They can be made starting either from a single strand or from two or more strands in which one or more have been “opened” to give the “bulky” aspect of textured yarn. Textured glass yarn is used in var

20、ious applications, for example insulation, filtration, the manufacture of decorative textiles, the reinforcement of plastics and the manufacture of packing materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference

21、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 472, Plastics Vocabulary ISO 1887, Textile glass Determination of combustible-matter content ISO 1888, Textile glass Staple fibres or filaments Determinati

22、on of average diameter ISO 1889, Reinforcement yarns Determination of linear density ISO 2078, Textile glass Yarns Designation ISO 3341, Textile glass Yarns Determination of breaking force and breaking elongation ISO 3344, Reinforcement products Determination of moisture content 3 Terms and definiti

23、ons For the purposes of this document, the terms and definitions given in ISO 472 apply. 4 Designation The designation of the yarn shall conform to ISO 2078. BS ISO 8516:2011 ISO 8516:2011(E) 2 ISO 2011 All rights reserved5 Physical properties 5.1 General Unless otherwise agreed, textured glass yarn

24、s shall be defined by the characteristics specified in 5.2 to 5.7, and nominal values and tolerances shall be given for these characteristics in the suppliers technical specification. The criteria for acceptance or rejection of a batch, based on the results of testing, shall also be given in the sup

25、pliers specification. 5.2 Type of glass Various types of glass are used in the production of textured yarns. A list of available glass types is given in ISO 2078. 5.3 Size content The texturizing process requires the use of yarn covered with size to give suitable lubrication during texturization. Th

26、is size can be eliminated after weaving by a heat-cleaning treatment, if necessary. The size content shall be determined in accordance with ISO 1887. 5.4 Average filament diameter The average filament diameter shall be determined in accordance with ISO 1888. 5.5 Linear density The linear density sha

27、ll be determined in accordance with ISO 1889, taking care, when taking the test specimens, that the yarn is tensioned to a level suitable for staple-fibre yarns in order to ensure that the specimens will be of the required length. 5.6 Moisture content The moisture content shall be determined in acco

28、rdance with ISO 3344. 5.7 Breaking load At the yield point, textured yarn can possess a strength which is much less than the breaking load. If this is the case, the suppliers specification shall indicate the minimum value of the strength at yield and the minimum value of the breaking strength, as de

29、termined in accordance with ISO 3341. BS ISO 8516:2011 ISO 8516:2011(E) ISO 2011 All rights reserved 36 Visual properties Defects 6.1 General The suppliers technical specification shall indicate the normal visual characteristics and defects that can be present on the yarns and packages (see examples

30、 in 6.2 and 6.3). The acceptable level with regard to number or importance shall be agreed between supplier and buyer. If necessary, reference samples shall be kept by the supplier in order to assess any disputed packages, especially for the defects described in 6.2.3, 6.3.2, 6.3.3 and 6.3.10. 6.2 V

31、isible defects of yarn 6.2.1 Dirty yarn. 6.2.2 Incorrect number of ends or mixed yarn. 6.2.3 Lack of texturization. 6.2.4 Damaged yarn. 6.2.5 Fuzz balls, slubs. 6.2.6 Presence of knots or splices (when they are not allowed). 6.2.7 Badly made knots or splices (when they are allowed). 6.3 Visible defe

32、cts of packages 6.3.1 Package badly made up. 6.3.2 Package too soft. 6.3.3 Package too hard. 6.3.4 Trapped end or foreign yarn. 6.3.5 Trapped foreign matter. 6.3.6 Sloughed yarn. 6.3.7 Dirt spots. 6.3.8 Package damaged. 6.3.9 Incorrect identification. 6.3.10 Shiny yarn (due to lack of size or lack o

33、f texturization). 6.3.11 Dirty or incorrectly joined (or transferred) ends or unjoined ends (when joined ends were specified). BS ISO 8516:2011 ISO 8516:2011(E) 4 ISO 2011 All rights reserved7 Delivery 7.1 Presentation and packaging The specification shall include any requirements for the presentati

34、on and packaging of the yarn. 7.2 Labelling The specification shall include a requirement that the container holding the yarn packages be provided with an external label including the following information: the designation of the yarn; the type of yarn package or a code-number indicating the type; t

35、he type of container or a code-number indicating the type; the net mass of the yarn packages in the container; the name of the supplier; the date of manufacture. 8 Storage The specification shall include any requirements concerning the storage conditions (temperature, relative humidity, time) necess

36、ary to ensure retention of the properties of the yarn. BS ISO 8516:2011BS ISO 8516:2011 ISO 8516:2011(E) ICS 59.100.10 Price based on 4 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other stand

37、ards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel

38、+44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be gra

39、teful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual u

40、pdating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the webs

41、ite In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those tha

42、t have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic i

43、nformation services are also available which give details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For deta

44、ils of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.b

45、si- Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Ex- cept as permitted under the Copyright, Designs and Patents Act 1988 no ex- tract may be reproduced, stored in a retrieval system or

46、 transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copy- right & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: