BS ISO 6986-2013 en_5593 Side and face milling (slotting) cutters with indexable inserts Dimensions《带可转位刀片的三面刃铣刀(开槽) 尺寸》.pdf

《BS ISO 6986-2013 en_5593 Side and face milling (slotting) cutters with indexable inserts Dimensions《带可转位刀片的三面刃铣刀(开槽) 尺寸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6986-2013 en_5593 Side and face milling (slotting) cutters with indexable inserts Dimensions《带可转位刀片的三面刃铣刀(开槽) 尺寸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 6986:2013 Side and face milling (slotting) cutters with indexable inserts DimensionsBS ISO 6986:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6986:2013. It supersedes BS4193-12:1984 which is withdrawn. The UK participat

2、ion in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contr

3、act. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 81023 7 ICS 25.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the

4、 authority of the Standards Policy and Strategy Committee on 30 September 2013. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 6986:2013 ISO 2013 Side and face milling (slotting) cutters with indexable inserts Dimensions Fraises trois tailles plaquettes amovibles D

5、imensions INTERNATIONAL STANDARD ISO 6986 Second edition 2013-09-01 Reference number ISO 6986:2013(E)BS ISO 6986:2013ISO 6986:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or

6、 utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO co

7、pyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6986:2013ISO 6986:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Dimensions

8、. 1 Annex A (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) 3 Bibliography 4BS ISO 6986:2013ISO 6986:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b

9、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a

10、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are

11、described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to

12、 the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the I

13、SO list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edg

14、es made of hard cutting materials. This second edition cancels and replaces the first edition (ISO 6986:1983), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 6986:2013INTERNATIONAL ST ANDARD ISO 6986:2013(E) Side and face milling (slotting) cutters with indexable inse

15、rts Dimensions 1 Scope This International Standard specifies the dimensions of side and face milling (slotting) cutters with indexable inserts. The shape and dimensions of the inserts are left to the discretion of the manufacturer. 2 Normative references The following documents, in whole or in part,

16、 are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 240, Milling cutters Interchangeability dimensio

17、ns for cutter arbors or cutter mandrels 3 Dimensions See Figure 1 and Table 1. a The value of 90 is the nominal cutting edge angle of the insert. Figure 1 Dimensions ISO 2013 All rights reserved 1BS ISO 6986:2013ISO 6986:2013(E) Table 1 Dimensions Dimensions in millimetres d j s 16 d 1 b H7 d 2 min.

18、 l l 1 80 27 41 10 10 100 32 47 10 10 12 12 125 40 55 12 12 16 16 160 40 55 16 16 20 20 200 50 69 20 20 25 25 bThe dimensions of the bore and key shall be in accordance with ISO 240.2 ISO 2013 All rights reservedBS ISO 6986:2013ISO 6986:2013(E) Annex A (informative) Relationship between designations

19、 in this International Standard and ISO 13399 (all parts) For the relationship between designations in this International Standard and preferred symbols according to the ISO 13399 series, see Table A.1. Table A.1 Relationship between designations in this International Standard and the ISO 13399 seri

20、es Symbol in this Inter- national Standard (ISO 6986) Reference in this International Standard (ISO 6986) Property name in the ISO 13399 series Symbol in the ISO 13399 series Reference in the ISO 13399 series d Figure 1 and Table 1 Cutting diameter DC ISO/TS 13399-3 71D084653E57F d 1 Figure 1 and Ta

21、ble 1 Connection diameter DCON ISO/TS 13399-3 71EBDBF5060E6 d 2 Figure 1 and Table 1 Hub diameter DHUB ISO/TS 13399-3 71D087D3B17B0 l Figure 1 and Table 1 Cutting width CW ISO/TS 13399-3 71CEAEBE2B825 l 1 Figure 1 and Table 1 Hub thickness THUB ISO/TS 13399-3 71D087D3F5E07 90 Figure 1 Tool cutting e

22、dge angle KAPR ISO/TS 13399-3 71D078F683C9B ISO 2013 All rights reserved 3BS ISO 6986:2013ISO 6986:2013(E) Bibliography 1 ISO 13399 (all parts), Cutting tool data representation and exchange4 ISO 2013 All rights reservedBS ISO 6986:2013BS ISO 6986:2013ISO 6986:2013(E) ISO 2013 All rights reserved IC

23、 S 25.100.20 Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are

24、published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based so

25、lutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you wit

26、h the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European

27、and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services a

28、re designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshe

29、d daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing M

30、embers. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications o

31、n your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We

32、continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and

33、 other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under

34、the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licens

35、ing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW