Automatic Picking of First Arrivals.ppt

《Automatic Picking of First Arrivals.ppt》由会员分享，可在线阅读，更多相关《Automatic Picking of First Arrivals.ppt（23页珍藏版）》请在麦多课文档分享上搜索。

1、1,Automatic Picking of First Arrivals,He Dian and Ting Sun,Definition,The first-break picking is that of identifying or picking the first arrivals of refracted signals from all the signals received by the receiver arrays for a particular source signal generation.,2,Direct arrivals Reflected arrivals

2、 Refracted arrivals,3,One of the methods for studying the near-surface low-velocity zone and for subsequent determination of static corrections is the technique of employing first arrivals.A common static correction is the weathering correction, which compensates for a layer of low seismic velocity

3、material near the surface of the Earth.,Why?,5,6,7,Application,Static corrections for seismic data processing, an important step in producing high-quality seismic sections.The weathering layer lead to near-surface low-velocity zone and produces travel-time anomalies , and the anomalies result in fal

4、se subsurface structures in later seismic processing. However, the anomalies can be corrected by using the first break arrival times on refraction signals.,8,Application,Detailed knowledge of the structure of the low-velocity zone.,9,Application,Used as observation data in reservoir history matching

5、History matching is the act of adjusting a model of a reservoir until it closely reproduces the past behavior of a reservoir. The past behavior can be production data and pressure data, well log and seismic data. The accuracy of the history matching depends on the quality of the reservoir model and

6、the quality and quantity of observation data. Once a model has been history matched, it can be used to simulate future reservoir behavior with a higher degree of confidence.,10,The main difficulties are connected with the properties of noise on seismograms:There is always a non-zero level of noise b

7、efore first arrive.2. The analysis of field data shows that first arrival and noise can be spatially correlated over short distances.3. Other anomalies in the topography of the survey region.,Difficulties,Coherence method. Cross correlation method. Combination of the correlation method an linear lea

8、st squares prediction technique. Neural Networks. Fractal-based algorithm.,10/9/2018,12,Methods,Automatic picking of first arrivals,Assume that the data of first arrivals are presented by a seismogram uj,n with N traces recorded at points xn=nx, n=1, , N, at time moments tj=jt, j=1, , J.,13,Automati

9、c picking of first arrivals,First step of the algorithm Destruction of a possible spatial correlation of noise. This is achieved by suppression of noise with an amplitude below a certain level. This level is defined by estimation of the average maximum noise level in a given time-space window before

10、 the first arrivals.,14,Automatic picking of first arrivals,First step of the algorithm Let such a window be on the traces m1 to m2 For each trace m, the maximum noise level is defined,Average maximum level of noise,Define a unit step function, The process of noise suppression is expressed as,where

11、is a minimum threshold value of the ratio of the signal to the average maximum noise level.,15,Automatic picking of first arrivals,Second step of the algorithm is first-arrival detection. This is based on statistical estimates obtained by summation of traces along straight lines in given directions.

12、 In order to define the directions of summation, we introduce the dimensionless slowness:where x is the distance between traces, t is the time sampling interval and vk is the apparent velocity in the direction of summation.,16,Automatic picking of first arrivals,Second step of the algorithm Define a

13、 range of summation over L traces, with L=2LH+1 around the central trace n. Then by summation in direction Pk, get the average,And the standard deviationNow introduce the function,17,Automatic picking of first arrivals,Second step of the algorithmThe function can serve as a good estimate for signal-

14、to-noise ratio, as can be clearly seen from two extreme cases. (1) absence of signal gives a very small value for W (2) ideal signal on all traces gives infinite value for W,18,Automatic picking of first arrivals,Second step of the algorithm However, in practice we do not know the real distribution

15、of U and furthermore, we must deal with very small ranges of summation. Thus, propose the following criterion for signal detectionwhere assuming that on M traces (ML) there are random deviations of noise with the same amplitude a in a direction Pk. The noise is negligible on the remaining L-M traces

16、.,19,Automatic picking of first arrivals,Second step of the algorithmcan serve as a measure of reliability of signal detection. The inequality is a criterion for making a decision regarding the presence of a signal. This means that we eliminate the possibility of false detection due to random correl

17、ation of noise on M traces.,20,Automatic picking of first arrivals,Third step of the algorithm Find the time of first arrivals on trace n. Average in a given time window It,Next, for every value of k we find a minimum value of j, let it equal , for which the inequality is satisfied.,21,Automatic pic

18、king of first arrivals,Third step of the algorithm In order to increase the reliability of detection, we demand that this inequality is satisfied for several consecutive values of in j. Then, we find the minimum of all the values , let it equal . The valuethus is the estimate of the time of first arrivals on trace n.,22,Thanks Questions?,23,