ASTM A734 A734M - 12 Standard Specification for Pressure Vessel Plates, Alloy Steel and High-Strength Low-Alloy Steel, Quenched-and-Tempered (Withdrawn 2017).pdf
《ASTM A734 A734M - 12 Standard Specification for Pressure Vessel Plates, Alloy Steel and High-Strength Low-Alloy Steel, Quenched-and-Tempered (Withdrawn 2017).pdf》由会员分享,可在线阅读,更多相关《ASTM A734 A734M - 12 Standard Specification for Pressure Vessel Plates, Alloy Steel and High-Strength Low-Alloy Steel, Quenched-and-Tempered (Withdrawn 2017).pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A734/A734M 12Standard Specification forPressure Vessel Plates, Alloy Steel and High-Strength Low-Alloy Steel, Quenched-and-Tempered1This standard is issued under the fixed designation A734/A734M; the number immediately following the designation indicates the yearof original adoption or,
2、 in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers quenched-and-tempered alloysteel and high-strength lo
3、w-alloy steel plates for piping com-ponents and welded pressure vessels.1.2 Two types are covered, which provide two differentchemical compositions with the same tensile requirements.Both types are quenched-and-tempered to enhance mechanicalproperties.1.2.1 Type A is an alloy steel intended for use
4、at low ambienttemperatures of 80F 60C and higher.1.2.2 Type B is a high-strength low-alloy steel intended foruse at ambient temperatures of 20F 30C and higher.1.3 The maximum thickness of plates is limited only by thecapacity of the chemical composition and heat treatment tomeet the specified mechan
5、ical property requirements. Indi-vidual manufacturers should be consulted on thickness limita-tions since current industry limitations have not been ascer-tained to date.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI unit
6、s are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.2. Referenced Documents2.1 ASTM Standards:2A20/A20M Specificati
7、on for General Requirements for SteelPlates for Pressure VesselsA435/A435M Specification for Straight-Beam UltrasonicExamination of Steel PlatesA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Steel PlatesA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled St
8、eel Plates for Special Applica-tions3. General Requirements and Ordering Information3.1 Material supplied to this material specification shallconform to the requirements of Specification A20/A20M.These requirements outline the testing and retesting methodsand procedures, permissible variations in di
9、mensions and mass,quality, repair of defects, marking, loading, and orderinginformation.3.2 In addition to the basic requirements of thisspecification, certain supplementary requirements are availablewhen additional control, testing, or examination is required tomeet end use requirements. The purcha
10、ser is referred to thelisted supplementary requirements in this specification and tothe detailed requirements in Specification A20/A20M.3.3 If the requirements of this specification are in conflictwith the requirements of Specification A20/A20M, the require-ments of this specification shall prevail.
11、4. Manufacture4.1 Steelmaking PracticeThe steel shall be killed andshall conform to the fine austenitic grain size requirement ofSpecification A20/A20M.5. Heat Treatment5.1 The plates shall be heat treated by quenching andtempering. The austenitizing temperature shall be 1725F940C maximum. Tempering
12、 temperature shall be 1150 to1300F 620 to 705C.5.2 If the purchaser elects to perform the heat treatment, thematerial shall be accepted on the basis of mill tests made fromtest coupons heat treated in accordance with the purchase orderrequirements. If the test coupon heat treatment is not indicatedo
13、n the purchase order, the manufacturer shall heat treat the testcoupons under conditions he considers appropriate. The manu-facturer shall inform the purchaser of the heat-treat procedurefollowed in treatment of the test coupon.1This specification is under the jurisdiction of ASTM Committee A01 on S
14、teel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure Vessels.Current edition approved May 1, 2012. Published June 2012. Originallyapproved in 1976. Last previous edition approved in 2007 as A734/A734M 87a (2007). DOI:
15、 10.1520/A0734_A0734M-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appear
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTM A734 A734M 12 Standard Specification for Pressure Vessel Plates Alloy Steel and High Strength Low Quenched Tempered Withdrawn 2017

链接地址:http://www.mydoc123.com/p-286694.html